Find a Solar Panel Installer you can trust in Tetbury.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

Solar thermal panels are panels that can be used to heat your hot water. The collectors, which are either evacuated tube panels or flat plate collectors, harness heat from the sun and transfer it to a heat transfer liquid that heats up water that is stored in a hot water cylinder. You can use a boiler or immersion heater as a back-up in the winter or to heat the water up further to reach the right temperature.

Evacuated tube panels involve a bank of glass tubes mounted on the roof tiles, and while they’re usually more expensive, they’re more efficient than flat plate collectors. They’re exactly what they sound like – flat panels that can be fixed onto your roof tiles or integrated into the roof.

Having a solar thermal system will reduce your energy bills since heat from the sun is free, so you won’t have to rely on your traditional heating as much. You’ll also be doing your bit for the environment – if you have a natural gas heating system, you could save up to 295kg of CO2 every year.

Another benefit to solar thermal panels is that you might be eligible for payments through the Renewable Heat Incentive (RHI), which is a Government scheme to encourage people to take up renewable heating technologies. As long as you have your system installed by an MCS-registered installer and you meet a few other requirements, you could receive payments of up to £525 per year for seven years. And since the average solar thermal panel system costs £5,500, you could pay off over half of your system just with these payments. That’s not even considering that you could save up to £60 a year on your energy bills if you have a gas system.

One of the things that has been on the UK government’s agenda for some time now is to promote the use of renewable energy sources. In fact, the Renewable Energy Directive put out by the EU instructs all member countries to achieve a 20 percent renewable target before the year 2020. The UK’s commitment to this objective has been made quite glaring with a number of funding options that has been put in place to help business owners looking to solar panels on their properties. This commitment was also showcased by a reduction in the cost of solar panels, so new investors have little to worry about. Although there aren’t any grants in the conventional sense, but there are opportunities for solar panel funding in the UK. At present, the only scheme open to new applications is the SEG - Smart Export Guarantee which came into effect on 1st January, 2020.

In general, there are four notable incentives in the UK for solar panels which includes the aforementioned Smart Export Guarantee, Reduced VAT on Energy Saving Products, Feed-in Tariff ( no longer open to new applications ), as well as the Renewable Heat Incentive ( RHI - applies only to solar water heating ).

Being the only one still open to new applications, we’ll provide you with some insights on SEG. The Smart Export Guarantee allows small scale low-carbon electricity generators to receive payments for surplus energy they’re able to export back to the grid. Although, this is not a direct government scheme, all licensed suppliers are necessitated to offer an export tariff to their customers. Those suppliers with more than 150,000 customers are obligated to offer a tariff, while the suppliers with fewer customers can partake on a voluntary basis.

To have your solar panels working at full strength at all times is crucial as this can go a long way to help you reduce your energy bill. In order to achieve this, you simply can’t afford to ignore having them regularly cleaned and free from all sorts of dirt, dust, debris, pollen, bird droppings and the likes. Now it’s quite reasonable to think rain or wind should be able to get the job done, but unfortunately this is not so. What solar panels need is a proper clean which you can decide to do by yourself or call in a qualified professional – the latter which is strongly recommended.

Cleaning of solar panels has to do with working at heights which can be very dangerous especially if you don’t have enough confidence to pull it off. And even if you have zero phobia for heights, solar panel cleaning requires experience as well as some specialized skills and tools possessed by the professionals. However, the question here is, how often should solar panels be cleaned to keep them operating at optimal efficiency?

Well, according to the manufacturers, solar panels should be cleaned twice a year. However, if this is something that you feel is not achievable by you, then you should at least give then an annual clean. The best or most advisable time to do this during the year is at the end of the summer months. This will ensure that you have a fully functioning solar array which is ready and prepared to withstand whatever the cold period throws at you. At the end of the day, you’d have them looking spotless clean while also working at full strength and reducing your energy bills.

Are you thinking of installing solar thermal systems in your home or property and wondering exactly how it works to generate electricity? Regardless of your motive, in this article you’ll learn in simple details how solar thermal is how solar thermal doesn't provide electricity for your home.

If you are looking to generate electricity for your home then Solar PV are able to generate electricity simply by absorbing and focusing sunlight in such a way to create a temperature level that’s high enough to generate the much needed electricity. There are two main components that comes with the solar energy collectors of each. These two components include, the reflectors ( mirrors), which works to absorb and concentrate the sunlight onto a receiver. In several types of the solar thermal power systems, a heat transfer fluid is then heated and distributed in the receiver so as to generate steam. Once the steam as been produced, it’s then transported to the turbine where it’s turned into a mechanical energy, which in turn powers the generator to produce electricity.

Solar thermal power or electric systems are usually embedded with a tracking system which keeps the sunlight concentrated on the receiver all day long as the sun changes position in the sky. They also come with a wide array of collectors which works of distribute the heat absorbed to a turbine as well as the generator. A lot of solar thermal power facilities will gave two or more plants with different arrays and generators.

Solar thermal power systems can also have a thermal energy storage system component whose work is to permit the solar collector system to heat an energy storage system during the day while energy storage system’s generated heat is incorporated in the production of electricity at night or during a cloudy weather when there’s not much sunlight.

Solar thermal panels work by capturing heat directly from the sun and using it to heat water. This hot water is then passed through a coil to heat the water for your central heating system. Solar thermal systems are compatible with many existing conventional boilers with hot water tanks, and can be set up to feed in to your existing heating system.

In a similar way to other major home improvement projects, some specific requirements must be met to allow for the installation of solar panels. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Generally, solar panels are covered under what’s called “Permitted Development” which gives you the freedom to install your solar panels without having to apply for a planning permission. However, there are some exceptions to this rule. These exceptions include if your house is a listed building or if your house is located within a conservation area. In these exceptional cases, it’s possible that you’ll need to apply for a planning permission, but this will largely depend on the discretion of your Local Planning Authority. What’s more? Solar panels are usually subjected to normal building regulations which includes examining the roof to make sure that it can support the additional weight. You can call in a MCS certified installer to carry out this check for you.

In order to install your solar PV on your roof, you must follow these guidelines:

✓ Your solar panels shouldn’t go beyond the highest point of the roof (excluding chimneys).

✓ The solar panels shouldn’t project beyond 200mm off the roof’s edge.

✓ The solar panels should be removed once they’re no longer used to produce electricity

✓ The solar panels should be installed such that the area and building’s appearance change is minimized.

It’s vital to purchase a solar panel system that suits your property. If you’re investing in a solar panel system, it makes the most financial sense to get the biggest one possible. However, whether you can do this or not depends on budget and space.

Here’s an idea of how much roof or ground space you’ll need to install a few different sizes of commercial solar panel system.

Solar panel system size, No. of solar panels, Approximate area required

11kW, 44, 64m²

20kW, 80, 116m²

30kW, 120, 173m²

40kW, 160, 231m²

50kW, 200, 288m²