Find a Solar Panel Installer you can trust in Seaview.

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

Like every other systems in your home, solar hot water systems will require periodic inspections as well as a regular maintenance in order to keep it running as efficiently as it should. Not only that, the various components will also require either repair or replacement from time to time. It’ll also be proactive to take the necessary precautions so as to prevent worrying issues like corrosion, scaling or freezing.

Is it a task you can handle on your own? Well, there are some inspections and maintenance activities you should be able to handle on your own, however, you’ll also require a qualified technician to carry out the more technical or complicated tasks. You should also take note that it may actually be more cost effective to have some systems replaced, shut off or removed completely than having it repaired. Here are some of the essential inspections that should be carried out on solar system components. They include:

✓ Collector soiling. Periodic cleaning of your collectors is important especially in dry and dusty climates.

✓ Plumbing, ductwork and wire connections. Check the pipe connections for fluid leaks. Examine duct connections and seals. Also make sure that all wire connections are tight.

✓ Roof penetrations. Flashing and sealant around the roof penetration should be checked to see that it’s in a good shape.

✓ Collector shading. Check for shading of the collectors on annual basis as this may greatly affect their performance.

✓ Support structures. Examine all bolts and nuts which connects the support structures to the collectors for tightness.

✓ Heat transfer fluids. Anti freeze solutions in liquid solar heating collectors will have to be replaced periodically. And this right here is a task that’s best handled by a licensed technician.

If you want to test your solar panel system to see if it’s working properly or just to see what output it’s giving, you can do this using a multimeter to measure current, or amps, and voltage.

Before you start, you’ll need to find the voltage (v) and current (A) ratings of your panel. You should be able to find them on the back of the panel. You should also make sure that it’s a nice clear, sunny day to get the best readings out of your panel. You should also check that it’s safe to be up on your roof!

To measure open circuit voltage, you’ll need to make sure that your solar panel is completely disconnected from your system’s regulator and battery (if you have one). Angle the panel towards the sun, and ensure that your multimeter is set to measure volts. Measure the voltage between the positive and negative terminals by connecting the negative contact on the voltmeter to the negative on the panel and the positive contact on the voltmeter to the positive on the panel.

Then, you can move on to the short circuit current. Follow the same steps as the open circuit voltage, but ensure that your multimeter is set at 10A to start with.

Only try to test your solar panel if it’s safe to do so. If your roof isn’t accessible without scaffolding or specialist equipment, consider speaking to an MCS-registered solar company about your concerns. They may recommend that they come to service your solar panel system.

With the numerous benefits that comes with the installation of solar panels, it should not be an option for just a few just because of the size and/or pitch of their roof. A number of individuals with flat roofs decide against solar panels due to the fact that they believe that the panels can’t be installed due to the lack of direct sunlight. However, in truth, this thought is absolutely incorrect. This is because it is actually very possible to fit solar panels on flat roofs and you can also benefit from a good amount of electricity that’ll be generated over time. In this post, we’re going to look at the possibilities involved in the installation of commercial solar panels on a flat roof. Let’s get started!

In reality, flat roof solar systems are mostly found on commercial buildings as their roof is typically made to be flat. Although, it’s important to note that it’s absolutely possible for them to be fitted on domestic properties too. The type of solar array that’s installed makes use of the same type of solar panel as a conventional system, however, there are some considerations that’ll have to be made moving forward. The array must be able to self clean during the rainy season while also avoiding damage whenever there’s a strong wind. The installation company you choose should take the pitch of the system into account, so as to make sure that its able to capture as much energy from the sun as possible. And that’s exactly why you should consider the use of thin film solar cells which are very flexible and moves with the sun as the day goes by, securing as much sunlight as possible as its always in direct light.

Are you thinking about installing a solar thermal system in your home? If yes, the you’d most likely be wondering the exact amount the system is going to cost. Well, you’re not alone. This is one of the most common question when it comes to solar thermal systems and we aim to answer that in this article. So let’s get started!

Unfortunately, the cost of a solar thermal system can’t be given in a single, accurate answer as they vary widely. However, when getting a new solar thermal system, you can expect to pay a sum within the range of £3000 to £6000 ( this includes a lowered VAT rate of 5 percent). The figures provided takes into account the installation costs as well as all the parts ( such as control panel, solar collectors, hot water tank and pipes).

To determine the price of your system, the quality and type of the panels matter. For instance, according to the Solar Trade Association, a properly insulated twin coil cylinder system would be priced at around £4500. in the same tone, it’s also possible to get DIY solar thermal kits that includes all the required hardware which will cost within the range of £1500 to £250. This however, may not be eligible for government support. In order to benefit from the RHI, your system must be fitted by a MCS accredited installer.

The varying prices of the solar thermal system’s initial cost is based on the specification of each individual house. For example, in situations where the building is having complicated water system, the plumbing cost is expected to increase which will have a serious impact on the overall cost of the solar thermal power system.

If you’re thinking about installing a solar system in your home or property, this is probably one of the things you’d like to know before making a purchase decision. Well, you’ve come to the right place! In this post, we’re going to give you a good insight into this to help you make the best informed decision possible moving forward. Let’s take a look!

First and foremost, it must be stated that providing a short and accurate answer to this question is nearly impossible as the amount of time a solar panel will last after dark is influenced by a number of factors. These factors include the size of your solar system, the battery size as well as your power usage. As you would have imagined, batteries are charged when there is excess energy that’s being produced by your solar system but it’s not being incorporated to power your home or property. More often than not, this occurs during the sunlight’s peak periods from about 10am to 2pm.

The time it’ll take for your battery to charge is influenced by the size of your solar system in Kilowatts, the size of your battery as well as the rate in which your system is being used. Your battery can be charged in a day or two, of course unless it’s an over-sized battery for your system.

When the sun sets and your solar panels can no longer directly run your appliances via electricity generation, the battery then kicks in. You will use about 1 to 2 kW’s of power if you’re watching TV, using the oven as well as lights internet etc. in other words, even a small solar panel battery will last all night. However, the same doesn’t apply if you’re having a party with running floodlights, three fridges and air conditioner as the battery will drain a lot faster.

In a similar way to other major home improvement projects, some specific requirements must be met to allow for the installation of solar panels. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Generally, solar panels are covered under what’s called “Permitted Development” which gives you the freedom to install your solar panels without having to apply for a planning permission. However, there are some exceptions to this rule. These exceptions include if your house is a listed building or if your house is located within a conservation area. In these exceptional cases, it’s possible that you’ll need to apply for a planning permission, but this will largely depend on the discretion of your Local Planning Authority. What’s more? Solar panels are usually subjected to normal building regulations which includes examining the roof to make sure that it can support the additional weight. You can call in a MCS certified installer to carry out this check for you.

In order to install your solar PV on your roof, you must follow these guidelines:

✓ Your solar panels shouldn’t go beyond the highest point of the roof (excluding chimneys).

✓ The solar panels shouldn’t project beyond 200mm off the roof’s edge.

✓ The solar panels should be removed once they’re no longer used to produce electricity

✓ The solar panels should be installed such that the area and building’s appearance change is minimized.