Find a Solar Panel Installer you can trust in Lytham St Annes.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

There are a wide range of benefits you stand to derive by installing solar panels for your business operations. Not only can it help you save money,  but it can also go a long way to help reduce your business’ environmental footprint. Regardless of whether your company is big or small, it can still benefit immensely by making use of solar panels. If you’re considering the installation of solar panels in your business environment, then you probably want to know just how much it’ll cost to complete the project. In order to help you make the most informed purchase decision, we’ve created this post to give you a good insight into commercial solar panel pricing. Let’s take a look!

Generally, the cost of commercial solar panels is within the range of £16000 to £70000 for small to mid-sized companies. However, there are a number of factors that can influence the cost of commercial solar panels which includes the size of the roof, the amount of energy that’s generated as well as the number incorporated. There is a need to evaluate the cost of solar panels so as to determine whether or not they’re a feasible option for your business. In order to determine the amount of energy your company uses per month, simply take a closer look at your utility bill.  This should indicate just how much energy you use per month as well as how much the utility company charges per kW. In general, most small to medium sized companies will incorporate 30,000 to 50,000 kWh annually and you can expect the cost to differ based on your location and the size of your system. The rule of thumb with larger systems is to calculate using £1000 per kW, plus VAT as the yardstick.

There are a few factors that will determine whether it’s worth getting a solar battery. They involve how much electricity you use, how often you’re at home and whether you receive any export payments.

To work out whether it’s worth getting a solar battery, you need to work out how much of the electricity you generate you’re using already. If you’re able to run all your appliances during the day while your solar panels generate electricity, then it sounds like you’re already using your electricity well. It might not be worth you getting a solar battery in this case.

However, if you’re not at home for a lot of the day, then you’ll be missing out on the electricity your panels are generating while the sun’s shining. If you install a solar battery system, you can store the electricity that your panels generate in the battery and use it when you get home. This will help you cut your electricity bills even further.

You’ll also need to consider whether you’re getting paid to export your electricity. If you’re on the Feed-in Tariff scheme (FITs) or receive payments from the Smart Export Guarantee (SEG), you’ll get paid for every unit of electricity you export to the National Grid. Before you decide whether it’s worth getting a solar battery, you’ll need to weigh up whether you’d be better off carrying on exporting your unused electricity rather than storing it to use yourself. If you’re unsure, visit the Energy Saving Trust’s website or speak to an MCS-registered installer who will be able to help you work out which is more cost-effective.

Just like other major house improvement projects, some specific requirements must be met to allow for the installation of solar panels on commercial buildings. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Fortunately, the installation of solar panels on commercial buildings may be “permitted development which mean you won’t have to apply to the Local Planning Authority for planning permission. There are, however, some important limits and conditions which must be put into consideration in order to benefit from these permitted development rights. Some of the limitations include:

• The solar panels must be installed on a wall or pitched roof that should project at a maximum of 200mm from the surface of the wall or roof slope.
• Equipment placed on a roof should not be within one metre of the external edge of that roof.
• Equipment mounted on a wall must not be within one metre of a junction of that wall with another wall or with the roof of the building
• If the equipment is on the roof of a building, the capacity for generation of electricity across the entire site must not be more than 1 megawatt.
• In the situation whereby the panels are installed on a flat roof, the highest part of the equipment should not exceed one metre above the highest part of the roof.

In general, obtaining a planning permission is very important and as such, you must discuss your position with your chosen installation company before you proceed.

Are you thinking of installing solar thermal systems in your home or property and wondering exactly how it works to generate electricity? Regardless of your motive, in this article you’ll learn in simple details how solar thermal is how solar thermal doesn't provide electricity for your home.

If you are looking to generate electricity for your home then Solar PV are able to generate electricity simply by absorbing and focusing sunlight in such a way to create a temperature level that’s high enough to generate the much needed electricity. There are two main components that comes with the solar energy collectors of each. These two components include, the reflectors ( mirrors), which works to absorb and concentrate the sunlight onto a receiver. In several types of the solar thermal power systems, a heat transfer fluid is then heated and distributed in the receiver so as to generate steam. Once the steam as been produced, it’s then transported to the turbine where it’s turned into a mechanical energy, which in turn powers the generator to produce electricity.

Solar thermal power or electric systems are usually embedded with a tracking system which keeps the sunlight concentrated on the receiver all day long as the sun changes position in the sky. They also come with a wide array of collectors which works of distribute the heat absorbed to a turbine as well as the generator. A lot of solar thermal power facilities will gave two or more plants with different arrays and generators.

Solar thermal power systems can also have a thermal energy storage system component whose work is to permit the solar collector system to heat an energy storage system during the day while energy storage system’s generated heat is incorporated in the production of electricity at night or during a cloudy weather when there’s not much sunlight.

If you’re looking to install some new solar panels in your home or property, then you’d probably want to know how it works. This is one of the most frequent questions asked by homeowners when it comes to solar panels and in this article we aim to give you a good insight on the operations of solar panels. Let’s have a look!

Generally, solar panels work by absorbing the energy of the sun and then converting it into electricity. It functions by allowing photons from the rays of the sun release the electrons free from atoms within the photovoltaic or solar cells in order to produce a flow of electricity. There are several solar cells that are connected together ( usually 60 or 72 ) in each panel. Individual cells comprises both a negative layer and a positive one which combines perfectly to create an electrical field in which the energy is generated.

The boron that’s within the bottom layer generates the positive charge, while the phosphorous found in the silicon layer produces the negative charge. In order to convert the sun’s rays into the energy that’s going to be transported from the panels to the inverter, the two field will interact with one another.

In other words, solar panels work by turning photons from the sunlight into direct current which is transmitted to the inverter. Once it gets to the inverter, it’s then translated to alternating current and send this current to to your electric box which powers the entire home. If you do not wish to reduce the high bills that’s associated with renting power from the grid, the solar energy system is an efficient and affordable way to achieve this aim.

Like every other systems in your home, solar hot water systems will require periodic inspections as well as a regular maintenance in order to keep it running as efficiently as it should. Not only that, the various components will also require either repair or replacement from time to time. It’ll also be proactive to take the necessary precautions so as to prevent worrying issues like corrosion, scaling or freezing.

Is it a task you can handle on your own? Well, there are some inspections and maintenance activities you should be able to handle on your own, however, you’ll also require a qualified technician to carry out the more technical or complicated tasks. You should also take note that it may actually be more cost effective to have some systems replaced, shut off or removed completely than having it repaired. Here are some of the essential inspections that should be carried out on solar system components. They include:

✓ Collector soiling. Periodic cleaning of your collectors is important especially in dry and dusty climates.

✓ Plumbing, ductwork and wire connections. Check the pipe connections for fluid leaks. Examine duct connections and seals. Also make sure that all wire connections are tight.

✓ Roof penetrations. Flashing and sealant around the roof penetration should be checked to see that it’s in a good shape.

✓ Collector shading. Check for shading of the collectors on annual basis as this may greatly affect their performance.

✓ Support structures. Examine all bolts and nuts which connects the support structures to the collectors for tightness.

✓ Heat transfer fluids. Anti freeze solutions in liquid solar heating collectors will have to be replaced periodically. And this right here is a task that’s best handled by a licensed technician.