Find a Solar Panel Installer you can trust in Prenton.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

If you want to connect solar panels to a battery, it’s likely that it’s because you want to make sure that you don’t waste any electricity when your solar panels are generating energy but you’re not around to use it. Batteries are particularly useful for homeowners that have solar panels but are out during daylight hours; with a solar battery system, your solar panels will feed the electricity they generate into the battery for you to use when you get home.

If you want to connect your solar panels to a battery, the best thing to do is to get in touch with an MCS-registered company who can talk you through your options. There are different size batteries and the size that’s suitable for you will depend on how much electricity you plan to store and how large your solar panel system is. Some of the top brands of battery storage system include Tesla, SunPower and SolarEdge. If you want to be able to take advantage of selling electricity back to the grid through the Smart Export Guarantee (SEG), it’s worth getting an MCS-registered company to install your battery for you, as you may not be eligible for payments if you connect your solar panels to a battery yourself.

You should also consider whether your solar panel system is a ‘storage ready’ solar system. Today, most systems will be, since battery storage is becoming much more common. This means that your solar panel system will have an inverter that can easily integrate a battery. If this is the case, you should be able to purchase the battery you want and follow the manufacturer’s instructions to install it.

However, it’s worth bearing in mind that electricity is extremely dangerous when handled incorrectly. If something goes wrong, you could electrocute yourself or cause a fire. If your solar panels and battery cause a fire, it’s unlikely that your home insurance company would pay out if you connect the battery yourself. That's why it’s best to ask a reputable installer with all the correct qualifications to connect your solar panels to a battery for you.

If you’re looking to install a solar thermal system in your home, this is usually one of the first concerns several homeowners have. Being fully aware that solar water heating systems are usually more expensive than their counterparts - the conventional water heating systems, the question arises whether or not you’ll be able to save some money from your solar water heating system in the long run. In this article, we aim provide an answer to this important question. Let’s take a closer look!

When it comes to solar thermal systems, the money you’ll be able to save in the long run depends on a wide range of factors. These factor includes:

✓ Your system’s performance.

✓ Your geographical location and solar resource

✓ Your household’s hot water demand

✓ Financing and incentive options that are available.

✓ The cost of fuel that’s being used for your alternative or backup water heating system, if you own one.

✓ The cost of conventional fuels such as oil, electricity or natural gas.

There are several benefits, however, that comes with the installation of a solar water heating system. Since the sun is absolutely free, future fuel shortages and price hikes will have little impact on you. Also, on the average if you decide to fit a solar thermal system your water heating bills is expected to drop about 50 percent to 80 percent. What’s more? The economics are even a lot more attractive when you’re just about to build a new home or refinancing. When you include the price of a solar water system in a 30 year mortgage, it’ll normally amount to very low price per month. Therefore, on a monthly basis you’ll be saving more and paying less.

To have your solar panels working at full strength at all times is crucial as this can go a long way to help you reduce your energy bill. In order to achieve this, you simply can’t afford to ignore having them regularly cleaned and free from all sorts of dirt, dust, debris, pollen, bird droppings and the likes. Now it’s quite reasonable to think rain or wind should be able to get the job done, but unfortunately this is not so. What solar panels need is a proper clean which you can decide to do by yourself or call in a qualified professional – the latter which is strongly recommended.

Cleaning of solar panels has to do with working at heights which can be very dangerous especially if you don’t have enough confidence to pull it off. And even if you have zero phobia for heights, solar panel cleaning requires experience as well as some specialized skills and tools possessed by the professionals. However, the question here is, how often should solar panels be cleaned to keep them operating at optimal efficiency?

Well, according to the manufacturers, solar panels should be cleaned twice a year. However, if this is something that you feel is not achievable by you, then you should at least give then an annual clean. The best or most advisable time to do this during the year is at the end of the summer months. This will ensure that you have a fully functioning solar array which is ready and prepared to withstand whatever the cold period throws at you. At the end of the day, you’d have them looking spotless clean while also working at full strength and reducing your energy bills.

Solar thermal panels are panels that can be used to heat your hot water. The collectors, which are either evacuated tube panels or flat plate collectors, harness heat from the sun and transfer it to a heat transfer liquid that heats up water that is stored in a hot water cylinder. You can use a boiler or immersion heater as a back-up in the winter or to heat the water up further to reach the right temperature.

Evacuated tube panels involve a bank of glass tubes mounted on the roof tiles, and while they’re usually more expensive, they’re more efficient than flat plate collectors. They’re exactly what they sound like – flat panels that can be fixed onto your roof tiles or integrated into the roof.

Having a solar thermal system will reduce your energy bills since heat from the sun is free, so you won’t have to rely on your traditional heating as much. You’ll also be doing your bit for the environment – if you have a natural gas heating system, you could save up to 295kg of CO2 every year.

Another benefit to solar thermal panels is that you might be eligible for payments through the Renewable Heat Incentive (RHI), which is a Government scheme to encourage people to take up renewable heating technologies. As long as you have your system installed by an MCS-registered installer and you meet a few other requirements, you could receive payments of up to £525 per year for seven years. And since the average solar thermal panel system costs £5,500, you could pay off over half of your system just with these payments. That’s not even considering that you could save up to £60 a year on your energy bills if you have a gas system.

Like every other systems in your home, solar hot water systems will require periodic inspections as well as a regular maintenance in order to keep it running as efficiently as it should. Not only that, the various components will also require either repair or replacement from time to time. It’ll also be proactive to take the necessary precautions so as to prevent worrying issues like corrosion, scaling or freezing.

Is it a task you can handle on your own? Well, there are some inspections and maintenance activities you should be able to handle on your own, however, you’ll also require a qualified technician to carry out the more technical or complicated tasks. You should also take note that it may actually be more cost effective to have some systems replaced, shut off or removed completely than having it repaired. Here are some of the essential inspections that should be carried out on solar system components. They include:

✓ Collector soiling. Periodic cleaning of your collectors is important especially in dry and dusty climates.

✓ Plumbing, ductwork and wire connections. Check the pipe connections for fluid leaks. Examine duct connections and seals. Also make sure that all wire connections are tight.

✓ Roof penetrations. Flashing and sealant around the roof penetration should be checked to see that it’s in a good shape.

✓ Collector shading. Check for shading of the collectors on annual basis as this may greatly affect their performance.

✓ Support structures. Examine all bolts and nuts which connects the support structures to the collectors for tightness.

✓ Heat transfer fluids. Anti freeze solutions in liquid solar heating collectors will have to be replaced periodically. And this right here is a task that’s best handled by a licensed technician.