Find a Solar Panel Installer you can trust in Uxbridge.

If you’re considering getting a solar thermal system, one of the first things that comes to mind is the possibility of the system functioning properly during the cold months. The short and simple answer to this question is yes, a solar thermal system works in the winter. However, the downside here is that it’ll be a lot less efficient when compared to how it operates during the warmer months or summer. As a result of this fact, you’ll likely need to rely more on your boiler, immersion heater or any other backup heating system during this period as your solar thermal system will fail to contribute as much as it does during the warmer months. So what exactly is the reason why solar thermal is less effective and less efficient in the winter period? Let’s have a look!

As you know, solar thermal system banks on the sun’s energy to heat the water for your home’s use. During the cold months or winter, the sunlight becomes a lot less available when compared to the warmer months, as a result, there’s less sunlight that’s available to be used for its solar energy. And even more so at the periods when the days are shorter or skies are clearly overcast.

Also having a great impact on a solar thermal system’s output is heavy snow. Flat plate collectors normally have the capacity to cope better during snowy conditions as the light that’s able to travel through the snow will heat up the absorber plate - thereby making the snow slide off more quickly. However, the case is contrary with evacuated tube collectors which possesses a form of vacuum insulation that’s crafted to minimize the loss of heat, meaning they can’t generate heat to melt and cause the snow to slide off in a similar way.

Just like other major house improvement projects, some specific requirements must be met to allow for the installation of solar panels on commercial buildings. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Fortunately, the installation of solar panels on commercial buildings may be “permitted development which mean you won’t have to apply to the Local Planning Authority for planning permission. There are, however, some important limits and conditions which must be put into consideration in order to benefit from these permitted development rights. Some of the limitations include:

• The solar panels must be installed on a wall or pitched roof that should project at a maximum of 200mm from the surface of the wall or roof slope.
• Equipment placed on a roof should not be within one metre of the external edge of that roof.
• Equipment mounted on a wall must not be within one metre of a junction of that wall with another wall or with the roof of the building
• If the equipment is on the roof of a building, the capacity for generation of electricity across the entire site must not be more than 1 megawatt.
• In the situation whereby the panels are installed on a flat roof, the highest part of the equipment should not exceed one metre above the highest part of the roof.

In general, obtaining a planning permission is very important and as such, you must discuss your position with your chosen installation company before you proceed.

Like every other systems in your home, solar hot water systems will require periodic inspections as well as a regular maintenance in order to keep it running as efficiently as it should. Not only that, the various components will also require either repair or replacement from time to time. It’ll also be proactive to take the necessary precautions so as to prevent worrying issues like corrosion, scaling or freezing.

Is it a task you can handle on your own? Well, there are some inspections and maintenance activities you should be able to handle on your own, however, you’ll also require a qualified technician to carry out the more technical or complicated tasks. You should also take note that it may actually be more cost effective to have some systems replaced, shut off or removed completely than having it repaired. Here are some of the essential inspections that should be carried out on solar system components. They include:

✓ Collector soiling. Periodic cleaning of your collectors is important especially in dry and dusty climates.

✓ Plumbing, ductwork and wire connections. Check the pipe connections for fluid leaks. Examine duct connections and seals. Also make sure that all wire connections are tight.

✓ Roof penetrations. Flashing and sealant around the roof penetration should be checked to see that it’s in a good shape.

✓ Collector shading. Check for shading of the collectors on annual basis as this may greatly affect their performance.

✓ Support structures. Examine all bolts and nuts which connects the support structures to the collectors for tightness.

✓ Heat transfer fluids. Anti freeze solutions in liquid solar heating collectors will have to be replaced periodically. And this right here is a task that’s best handled by a licensed technician.

It’s vital to purchase a solar panel system that suits your property. If you’re investing in a solar panel system, it makes the most financial sense to get the biggest one possible. However, whether you can do this or not depends on budget and space.

Here’s an idea of how much roof or ground space you’ll need to install a few different sizes of commercial solar panel system.

Solar panel system size, No. of solar panels, Approximate area required

11kW, 44, 64m²

20kW, 80, 116m²

30kW, 120, 173m²

40kW, 160, 231m²

50kW, 200, 288m²

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

So, you’ve finally decided to go for solar? If yes, then you’d also probably find yourself trying to figure out exactly what solar battery size is needed to power your home or property. This is one of the most common questions when it comes to the solar system world and understandably so. In this article, we aim to give you an idea of the solar size you’d need to power your home or property before making a purchase decision. Let’s take a look!

The first thing to do if you find yourself asking this question is to identify the reason why you want to purchase the solar battery in the first place. For some individuals, they simply want to save some excess energy being fed back into the grid, while others just want protection from possible blackouts. There are also some environment-conscious home or property owners who makes this decision in order to create a carbon-neutral home. Another crucial factor to consider is your budget. A full solar storage system can be quite costly, although this is cheaper than a decade ago. Generally, the size of solar battery you’ll require depends on the following:

• How much energy you’re able to generate: The size of your solar array as well as its efficiency will influence the amount of power it’ll be able to supply to your home.
• Your daily energy usage needs: Daily energy usage can vary greatly between households depending on a number of factors. These factors include the number of occupants, geographical location, type of building, general household energy usage and more. Some may find that their solar system cover for most of their energy usage, while others find themselves still relying heavily on the grid.

Are you thinking of installing solar thermal systems in your home or property and wondering exactly how it works to generate electricity? Regardless of your motive, in this article you’ll learn in simple details how solar thermal is how solar thermal doesn't provide electricity for your home.

If you are looking to generate electricity for your home then Solar PV are able to generate electricity simply by absorbing and focusing sunlight in such a way to create a temperature level that’s high enough to generate the much needed electricity. There are two main components that comes with the solar energy collectors of each. These two components include, the reflectors ( mirrors), which works to absorb and concentrate the sunlight onto a receiver. In several types of the solar thermal power systems, a heat transfer fluid is then heated and distributed in the receiver so as to generate steam. Once the steam as been produced, it’s then transported to the turbine where it’s turned into a mechanical energy, which in turn powers the generator to produce electricity.

Solar thermal power or electric systems are usually embedded with a tracking system which keeps the sunlight concentrated on the receiver all day long as the sun changes position in the sky. They also come with a wide array of collectors which works of distribute the heat absorbed to a turbine as well as the generator. A lot of solar thermal power facilities will gave two or more plants with different arrays and generators.

Solar thermal power systems can also have a thermal energy storage system component whose work is to permit the solar collector system to heat an energy storage system during the day while energy storage system’s generated heat is incorporated in the production of electricity at night or during a cloudy weather when there’s not much sunlight.