Find a Solar Panel Installer you can trust in Loanhead.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

Asides from the fact that solar energy can be converted into electricity with the help of solar panels, there’s also another pretty cool way the sun’s power can be harnessed - solar thermal technologies. These technologies are able to convert sunlight into heat rather than power and these are in fact the very first solar energy products that were commercialized in the United Kingdom. Solar thermal panels, in a similar way to solar PVs, can help in minimizing your carbon footprint while also assisting you to save good money on your energy bills by providing the much needed coverage for your heating needs with the help of a renewable energy source that’s totally free.

Solar thermal panels provides some great benefits which is capable of making all homeowners in the UK consider installing one in their respective homes. Let’s take a closer look at these benefits.

✓ When compared to solar PV panels, they’re a more affordable heating option and also have a shorter payback period.

✓ Solar thermal panels are more efficient than PV panels due to the fact that the heat waves are able to hold more energy than sunlight and also because there’s no electricity transformation process.

✓ Solar thermal panels are able to operate in cold climates, strong wind as well as overcast weather, and make use of an energy storage system.

✓ They can help you save about 600kg of carbon dioxide emissions on an annual basis.

✓ Although most of the solar thermal panel systems come with a warranty usually within the range of 5 to 10 years, they’re able to last up to 25 years. What’s more? The require just a little maintenance, meaning the main cost you’d have to worry about is the cost of installation.

Solar panels are a great source of energy with numerous benefits that comes with it. However, the main thing that puts off most homeowners or potential buyers is the fact that the equipment are usually very expensive. So if you’re planning to purchase solar panels to be installed in your home, then you’d probably want to know if it’s actually worth the investment or otherwise. In this article, we aim to give you a good insight into how solar panels works and if its a viable investment.

Generally, the length of time it will take for your solar panels to payback and whether you’ll be able to make money from them will be based on the following factors:

✓ The solar panel PV system’s cost.

✓ The amount of the generated electricity that you’re able to use.

✓ Whether as well as the amount you’re paid to the electricity you’re able to generate and export.

To know whether your solar panels are truly worth it, then a higher initial cost to fit the system will require to be settled with the amount you’re able to save through the use of the renewable electricity it produces, rather than making purchases from your electricity company. In other words, the more renewable energy you’re able to use, the more savings you make. If you’re registered for the FIT and paid per kWh of electricity produced, for 50 percent of that, which is assumed to be exported to the grid. Therefore, if you’re able to use more than 50 percent, you’ll be able to benefit from the investment.

In a similar way to other major home improvement projects, some specific requirements must be met to allow for the installation of solar panels. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Generally, solar panels are covered under what’s called “Permitted Development” which gives you the freedom to install your solar panels without having to apply for a planning permission. However, there are some exceptions to this rule. These exceptions include if your house is a listed building or if your house is located within a conservation area. In these exceptional cases, it’s possible that you’ll need to apply for a planning permission, but this will largely depend on the discretion of your Local Planning Authority. What’s more? Solar panels are usually subjected to normal building regulations which includes examining the roof to make sure that it can support the additional weight. You can call in a MCS certified installer to carry out this check for you.

In order to install your solar PV on your roof, you must follow these guidelines:

✓ Your solar panels shouldn’t go beyond the highest point of the roof (excluding chimneys).

✓ The solar panels shouldn’t project beyond 200mm off the roof’s edge.

✓ The solar panels should be removed once they’re no longer used to produce electricity

✓ The solar panels should be installed such that the area and building’s appearance change is minimized.

There are a few factors that will determine whether it’s worth getting a solar battery. They involve how much electricity you use, how often you’re at home and whether you receive any export payments.

To work out whether it’s worth getting a solar battery, you need to work out how much of the electricity you generate you’re using already. If you’re able to run all your appliances during the day while your solar panels generate electricity, then it sounds like you’re already using your electricity well. It might not be worth you getting a solar battery in this case.

However, if you’re not at home for a lot of the day, then you’ll be missing out on the electricity your panels are generating while the sun’s shining. If you install a solar battery system, you can store the electricity that your panels generate in the battery and use it when you get home. This will help you cut your electricity bills even further.

You’ll also need to consider whether you’re getting paid to export your electricity. If you’re on the Feed-in Tariff scheme (FITs) or receive payments from the Smart Export Guarantee (SEG), you’ll get paid for every unit of electricity you export to the National Grid. Before you decide whether it’s worth getting a solar battery, you’ll need to weigh up whether you’d be better off carrying on exporting your unused electricity rather than storing it to use yourself. If you’re unsure, visit the Energy Saving Trust’s website or speak to an MCS-registered installer who will be able to help you work out which is more cost-effective.

Not only will you reduce your electricity bill by generating your own electricity with solar panels, but you can also earn money through the SEG which is offered by large energy suppliers. They’ll pay you for the electricity you export back to the grid. You’ll also reduce your carbon footprint, lessening your impact on the environment.

If you want to test your solar panel system to see if it’s working properly or just to see what output it’s giving, you can do this using a multimeter to measure current, or amps, and voltage.

Before you start, you’ll need to find the voltage (v) and current (A) ratings of your panel. You should be able to find them on the back of the panel. You should also make sure that it’s a nice clear, sunny day to get the best readings out of your panel. You should also check that it’s safe to be up on your roof!

To measure open circuit voltage, you’ll need to make sure that your solar panel is completely disconnected from your system’s regulator and battery (if you have one). Angle the panel towards the sun, and ensure that your multimeter is set to measure volts. Measure the voltage between the positive and negative terminals by connecting the negative contact on the voltmeter to the negative on the panel and the positive contact on the voltmeter to the positive on the panel.

Then, you can move on to the short circuit current. Follow the same steps as the open circuit voltage, but ensure that your multimeter is set at 10A to start with.

Only try to test your solar panel if it’s safe to do so. If your roof isn’t accessible without scaffolding or specialist equipment, consider speaking to an MCS-registered solar company about your concerns. They may recommend that they come to service your solar panel system.