Find a Solar Panel Installer you can trust in Llanfechain.

Solar panels are made up of photovoltaic (PV) cells. These cells are made from silicon semiconductors, which absorb sunlight and convert it into electricity.

There are three main types of PV cell: monocrystalline solar cells, polycrystalline solar cells, and thin film solar cells. Monocrystalline cells are usually the most efficient and expensive, and thin film solar cells are the cheapest and least efficient. These are all made from silicone, but are manufactured in different ways.

Solar panels are a great source of energy with numerous benefits that comes with it. However, the main thing that puts off most homeowners or potential buyers is the fact that the equipment are usually very expensive. So if you’re planning to purchase solar panels to be installed in your home, then you’d probably want to know if it’s actually worth the investment or otherwise. In this article, we aim to give you a good insight into how solar panels works and if its a viable investment.

Generally, the length of time it will take for your solar panels to payback and whether you’ll be able to make money from them will be based on the following factors:

✓ The solar panel PV system’s cost.

✓ The amount of the generated electricity that you’re able to use.

✓ Whether as well as the amount you’re paid to the electricity you’re able to generate and export.

To know whether your solar panels are truly worth it, then a higher initial cost to fit the system will require to be settled with the amount you’re able to save through the use of the renewable electricity it produces, rather than making purchases from your electricity company. In other words, the more renewable energy you’re able to use, the more savings you make. If you’re registered for the FIT and paid per kWh of electricity produced, for 50 percent of that, which is assumed to be exported to the grid. Therefore, if you’re able to use more than 50 percent, you’ll be able to benefit from the investment.

If you want to test your solar panel system to see if it’s working properly or just to see what output it’s giving, you can do this using a multimeter to measure current, or amps, and voltage.

Before you start, you’ll need to find the voltage (v) and current (A) ratings of your panel. You should be able to find them on the back of the panel. You should also make sure that it’s a nice clear, sunny day to get the best readings out of your panel. You should also check that it’s safe to be up on your roof!

To measure open circuit voltage, you’ll need to make sure that your solar panel is completely disconnected from your system’s regulator and battery (if you have one). Angle the panel towards the sun, and ensure that your multimeter is set to measure volts. Measure the voltage between the positive and negative terminals by connecting the negative contact on the voltmeter to the negative on the panel and the positive contact on the voltmeter to the positive on the panel.

Then, you can move on to the short circuit current. Follow the same steps as the open circuit voltage, but ensure that your multimeter is set at 10A to start with.

Only try to test your solar panel if it’s safe to do so. If your roof isn’t accessible without scaffolding or specialist equipment, consider speaking to an MCS-registered solar company about your concerns. They may recommend that they come to service your solar panel system.

There are a few trusted companies in the UK that make solar panels. While there are other solar thermal panels out there that are made by Chinese and American companies, we’ll focus on the brands with a longstanding presence in the UK since these are the panels MCS-registered solar companies are likely to recommend to you.

Viessmann, Worcester Bosch, Solar UK and Dimplex make some of the best solar thermal panels in the UK. Dimplex and Viessmann offer both flat plate and evacuated tube solar panels, while Solar UK only offers evacuated tubes. Worcester Bosch’s Greenskies range are all flat plate collectors. Viessmann’s panels come with a 5-year warranty, while Worcester Bosch and Dimplex offer extensive 10-year warranties. However, Solar UK offer a comprehensive 25-year warranty and guarantee that the panels will deliver the same level of performance for 25 years!

We’d recommend choosing evacuated tube solar thermal panels because they are the most efficient. While there won’t be much difference between evacuated tubes and flat plates in the summer, in the winter evacuated tubes are much better at taking heat from the sun than flat plates. Since our winters are long and cold with few daylight hours, we think it makes sense to go with evacuated tubes. However, if your priority is looks over maximising efficiency, you might want to choose flat plate collectors since they sit flat on the roof and look more like solar PV panels, whereas the evacuated tubes will stick out.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

How Do Solar Panels And Batteries Work Together?

With solar panel system rapidly becoming an ubiquitous phenomenon within the modern society, several homeowners in the UK are just coming to terms with the numerous benefits offered by the system. The solar power’s popularity has even led to the rise of another renewable technology - solar batteries able to store excess solar power that can be used later. Now several companies such as Tesla are now building solar batteries that can be fitted alongside solar panels for your building. So how exactly do solar panels and batteries work together? Let’s have a look!

Solar panels make use of the sun light to generate electricity and as a result, they can’t function when sunlight is absent - giving a big issue of how to power your house when it’s dark. In the event whereby this occurs, you’re afforded two options which is either to contact energy providers to buy electricity or purchase a battery storage system.

So what’s the function of the battery storage system? Basically when your solar panel provides electricity which is not needed right away, a solar battery will work to convert the DC electricity into AC energy which is going to be stored for later use (when you actually need it). in other words, your solar panels charge the batteries when you do not require the energy they’re generating right away.

As a result, when it’s dark and the solar panels are no longer functioning, your system will tap into the energy that’s already been stored by your battery for later use. This way, you can be totally independent of the National Grid, which implies more savings on your electricity bills.