Find a Solar Panel Installer you can trust in Rutland.

Tesla’s top-of-the-range battery storage system is still one of the most expensive on the market. It has a huge 13.5kWh usable capacity and can even keep you up and running during a power cut. But how long does a Tesla Powerwall battery last? And does this mean it’s worth investing in one?

The Tesla Powerwall 2.0 comes with a 10-year warranty. But Tesla says that it should last way beyond this – at least 5 years longer. The standard warranty says that it should work at 70% capacity for the full 10 years – so if it loses more than 30% of its storage capacity within that time, it should still be covered.

While the Tesla Powerwall does last a long time, it has a large capacity that most average households won’t require, and it’s a costly option. After installation, the Powerwall 2.0 will set you back between £6,500 and £9,000, so ideally you want it to last past its 10-year warranty.

Before you splash out, consider the size of the solar panel system you want to install or you already have. Will it generate enough electricity to make it worth storing in the Powerwall? If not, are you expecting to upgrade your solar panels to a larger system in the future? If you are, then it might be worth investing in a Powerwall. It might also be better to wait until you come to upgrade your solar panels – the solar battery price trend is going the same way as solar panels, so they will probably continue to decrease in price as more people adopt the technology.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

Just like other major house improvement projects, some specific requirements must be met to allow for the installation of solar panels on commercial buildings. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Fortunately, the installation of solar panels on commercial buildings may be “permitted development which mean you won’t have to apply to the Local Planning Authority for planning permission. There are, however, some important limits and conditions which must be put into consideration in order to benefit from these permitted development rights. Some of the limitations include:

• The solar panels must be installed on a wall or pitched roof that should project at a maximum of 200mm from the surface of the wall or roof slope.
• Equipment placed on a roof should not be within one metre of the external edge of that roof.
• Equipment mounted on a wall must not be within one metre of a junction of that wall with another wall or with the roof of the building
• If the equipment is on the roof of a building, the capacity for generation of electricity across the entire site must not be more than 1 megawatt.
• In the situation whereby the panels are installed on a flat roof, the highest part of the equipment should not exceed one metre above the highest part of the roof.

In general, obtaining a planning permission is very important and as such, you must discuss your position with your chosen installation company before you proceed.

Solar energy is renewable, as the sunlight it uses won’t run out. This means that it’s a great way to generate electricity without damaging the planet. So, installing solar panels to generate solar energy can be a great move for businesses looking to reduce their carbon emissions.

The more you’re at home during the day, the more you can save on your electricity bill, since solar panels generate electricity during the day. The Feed-in Tariff scheme (FITs) ended in March 2019, but the new Smart Export Guarantee (SEG) pays you, via your energy supplier, for the electricity you export back to the grid. With the savings involved in generating your own electricity and SEG payments, you can expect to save up to £390 per year on your electricity bill.

Most people want to connect solar panels to a battery when they’re not at home all day to use the electricity they generate, or generate more than they consume over a day. Solar batteries are a great way to maximise the savings on your energy bills since you can use every unit of electricity you generate.

If you want to connect your solar panels to a battery, the best – and safest – way is to ask an MCS-registered company to do it for you. They’ve had lots of training and hold qualifications in handling electricity and installing solar batteries, so they will be able to recommend the best battery for your solar panels and for the among of electricity you use. Some of the brands they might recommend include Tesla, SolarEdge and SolaX, but there are many more to choose from. If you want to send electricity to the grid from your battery to receive Smart Export Guarantee (SEG) payments, it’s also worth leaving installation up to a registered installer. This is because you might not be eligible for payments if your battery wasn’t installed by an MCS-registered company.

However, if you do want to have a go at connecting your solar panels to a battery, it’s worth finding out whether your system is ‘storage ready’. Most relatively new systems will be, since batteries are becoming more commonplace. If your solar panels are storage ready, they will have an inverter that can easily have a battery added to it. If this is the case, then you should be able to buy the solar battery you want and follow the manufacturer's instructions to install it.

But it’s worth remembering that electricity is extremely dangerous when handled improperly. If you don’t get the solar battery connected properly and something goes wrong, it could cause a fire or you could electrocute yourself. If a fire breaks out due to your battery, it’s unlikely that your home insurance company would pay out since you connected the battery yourself. That’s why it’s always worth speaking to a registered installer to install a solar battery storage system for you.

Solar panels are made up of photovoltaic (PV) cells. These cells are made from silicon semiconductors, which absorb sunlight and convert it into electricity.

There are three main types of PV cell: monocrystalline solar cells, polycrystalline solar cells, and thin film solar cells. Monocrystalline cells are usually the most efficient and expensive, and thin film solar cells are the cheapest and least efficient. These are all made from silicone, but are manufactured in different ways.