Find a Solar Panel Installer you can trust in Newcastle.

If you’re thinking about installing a solar system in your home or property, this is probably one of the things you’d like to know before making a purchase decision. Well, you’ve come to the right place! In this post, we’re going to give you a good insight into this to help you make the best informed decision possible moving forward. Let’s take a look!

First and foremost, it must be stated that providing a short and accurate answer to this question is nearly impossible as the amount of time a solar panel will last after dark is influenced by a number of factors. These factors include the size of your solar system, the battery size as well as your power usage. As you would have imagined, batteries are charged when there is excess energy that’s being produced by your solar system but it’s not being incorporated to power your home or property. More often than not, this occurs during the sunlight’s peak periods from about 10am to 2pm.

The time it’ll take for your battery to charge is influenced by the size of your solar system in Kilowatts, the size of your battery as well as the rate in which your system is being used. Your battery can be charged in a day or two, of course unless it’s an over-sized battery for your system.

When the sun sets and your solar panels can no longer directly run your appliances via electricity generation, the battery then kicks in. You will use about 1 to 2 kW’s of power if you’re watching TV, using the oven as well as lights internet etc. in other words, even a small solar panel battery will last all night. However, the same doesn’t apply if you’re having a party with running floodlights, three fridges and air conditioner as the battery will drain a lot faster.

Solar cells , also referred to as photovoltaic cells (PV), absorbs energy from the sun and converts it to generate electricity. This, however, should not be confused with photovoltaic thermal cells or PVT which operates to generate heat for water in homes. Solar cells are linked electrically and also carefully organized into a large frame which is popularly called solar panels. Generally, solar cells are produced or made of silicon semi conductors which works to absorb sunlight and then turn it into electricity for use at a home. A solar panel comprises of either 60 or 72 solar cells which are electrically interconnected in series and parallel and also positioned in between glass and plastic which is then framed.

At present, solar panels incorporated for residential or domestic purposes only possesses the capacity to make use of only about 20 percent of the sunlight they’re able to absorb and convert it to electricity - also called solar efficiency. Available in the market are also a wide range of solar cell available for both industrial and commercial purposes. This type of solar panels have an efficiency rating of about 40 percent which will also automatically make them more costly than the domestic types.

One great thing about the solar industry is the fact that it keeps improving in such a way that raises both its efficiency as well as overall quality. And with further research and development, this is expected to even increase as the years go by. What’s more? As these aspects keep rising, it’s also expected that the solar panels price should be on a decrease. That way, they’ll become available to a wider range of individuals who’ll also like to save money on electricity bills and go greener.

If you’re looking to install some new solar panels in your home or property, then you’d probably want to know how it works. This is one of the most frequent questions asked by homeowners when it comes to solar panels and in this article we aim to give you a good insight on the operations of solar panels. Let’s have a look!

Generally, solar panels work by absorbing the energy of the sun and then converting it into electricity. It functions by allowing photons from the rays of the sun release the electrons free from atoms within the photovoltaic or solar cells in order to produce a flow of electricity. There are several solar cells that are connected together ( usually 60 or 72 ) in each panel. Individual cells comprises both a negative layer and a positive one which combines perfectly to create an electrical field in which the energy is generated.

The boron that’s within the bottom layer generates the positive charge, while the phosphorous found in the silicon layer produces the negative charge. In order to convert the sun’s rays into the energy that’s going to be transported from the panels to the inverter, the two field will interact with one another.

In other words, solar panels work by turning photons from the sunlight into direct current which is transmitted to the inverter. Once it gets to the inverter, it’s then translated to alternating current and send this current to to your electric box which powers the entire home. If you do not wish to reduce the high bills that’s associated with renting power from the grid, the solar energy system is an efficient and affordable way to achieve this aim.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

There are a wide range of benefits you stand to derive by installing solar panels for your business operations. Not only can it help you save money,  but it can also go a long way to help reduce your business’ environmental footprint. Regardless of whether your company is big or small, it can still benefit immensely by making use of solar panels. If you’re considering the installation of solar panels in your business environment, then you probably want to know just how much it’ll cost to complete the project. In order to help you make the most informed purchase decision, we’ve created this post to give you a good insight into commercial solar panel pricing. Let’s take a look!

Generally, the cost of commercial solar panels is within the range of £16000 to £70000 for small to mid-sized companies. However, there are a number of factors that can influence the cost of commercial solar panels which includes the size of the roof, the amount of energy that’s generated as well as the number incorporated. There is a need to evaluate the cost of solar panels so as to determine whether or not they’re a feasible option for your business. In order to determine the amount of energy your company uses per month, simply take a closer look at your utility bill.  This should indicate just how much energy you use per month as well as how much the utility company charges per kW. In general, most small to medium sized companies will incorporate 30,000 to 50,000 kWh annually and you can expect the cost to differ based on your location and the size of your system. The rule of thumb with larger systems is to calculate using £1000 per kW, plus VAT as the yardstick.

With the numerous benefits that comes with the installation of solar panels, it should not be an option for just a few just because of the size and/or pitch of their roof. A number of individuals with flat roofs decide against solar panels due to the fact that they believe that the panels can’t be installed due to the lack of direct sunlight. However, in truth, this thought is absolutely incorrect. This is because it is actually very possible to fit solar panels on flat roofs and you can also benefit from a good amount of electricity that’ll be generated over time. In this post, we’re going to look at the possibilities involved in the installation of commercial solar panels on a flat roof. Let’s get started!

In reality, flat roof solar systems are mostly found on commercial buildings as their roof is typically made to be flat. Although, it’s important to note that it’s absolutely possible for them to be fitted on domestic properties too. The type of solar array that’s installed makes use of the same type of solar panel as a conventional system, however, there are some considerations that’ll have to be made moving forward. The array must be able to self clean during the rainy season while also avoiding damage whenever there’s a strong wind. The installation company you choose should take the pitch of the system into account, so as to make sure that its able to capture as much energy from the sun as possible. And that’s exactly why you should consider the use of thin film solar cells which are very flexible and moves with the sun as the day goes by, securing as much sunlight as possible as its always in direct light.