Find a Solar Panel Installer you can trust in Falkirk.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

It may be hard to believe with the summers we have in the UK, but there is more than enough sunlight to power solar panels. Solar PV (photovoltaic) panels operate in daylight, rather than needing direct rays from the sun so they’ll work throughout the year.

After making the very important business decision to go solar, you may also want to know just how long it’ll take to complete the installation process and start generating electricity. After all, generating electricity is the main reason you made the switch to solar system. In this post, we’re going to provide you with in depth details on how long it takes to install solar panels as well as the factors that may affect that time.

The entire process of solar panels installation and getting them approved isn’t an overnight process. You’ll have to wait for periods for each step of the process whereby one must be completed before moving to the next. The time required to complete each step can, however, vary largely depending on your location, the type of solar panels you opt for, the solar company you hire as well as the number of people that’ll be making the installation. Here are the steps to a solar system installation and the estimated time each are expected to take:

• Site assessment. Once you chosen your solar company, the first step would be to have a solar professional from the company to visit the site to examine the roof and other features so as to make sure that they’re able to support a solar system. From the initial contact to scheduling the site visit, this step can take up to 1 to 2 weeks
• Local permitting. This involves getting the right permits from your local authorities. This can take up to 3 to 6 or more weeks.
• Solar system design. This may take up to a week or two depending on whether or not you need design approval and also where the parts are coming from
• Installation. This step can take a week or two depending on the size af your solar panel and roof.
• Inspection. This step can take up to a week depending on where you reside and how quickly the inspector can visit.
• Utility connection. Depending on your utility company, this step can take up to 2 weeks.

Just like other major house improvement projects, some specific requirements must be met to allow for the installation of solar panels on commercial buildings. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Fortunately, the installation of solar panels on commercial buildings may be “permitted development which mean you won’t have to apply to the Local Planning Authority for planning permission. There are, however, some important limits and conditions which must be put into consideration in order to benefit from these permitted development rights. Some of the limitations include:

• The solar panels must be installed on a wall or pitched roof that should project at a maximum of 200mm from the surface of the wall or roof slope.
• Equipment placed on a roof should not be within one metre of the external edge of that roof.
• Equipment mounted on a wall must not be within one metre of a junction of that wall with another wall or with the roof of the building
• If the equipment is on the roof of a building, the capacity for generation of electricity across the entire site must not be more than 1 megawatt.
• In the situation whereby the panels are installed on a flat roof, the highest part of the equipment should not exceed one metre above the highest part of the roof.

In general, obtaining a planning permission is very important and as such, you must discuss your position with your chosen installation company before you proceed.

In theory, you can fit solar panels yourself. In practice, it’s worth leaving it up to the professionals.

If you get DIY solar panels and install them on your roof yourself, you won’t be able to apply for the government-backed Smart Export Guarantee (SEG). The SEG pays you for every unit of electricity you generate and send back to the grid, so it’s a scheme well worth signing up for. However, you must have your solar panels installed by a Microgeneration Certification Scheme (MCS)-registered engineer or company, so you’ll miss out if you install the solar panels by yourself.

The other thing to consider about installing solar panels yourself is that you’re dealing with electricity. Electricity is extremely dangerous if handled incorrectly, so if you don’t have any qualifications in working with electricity you could be putting yourself and your family at risk. Connecting DIY solar panels yourself and doing it incorrectly could mean that you give yourself an electric shock or cause a fire. If your home is damaged due to a fire caused by solar panels you’ve installed yourself, it’s unlikely that your home insurance company would pay out.

Before having a go at installing your own solar panels, do some quick sums to see how much money it could really save you. A 3.5kW DIY solar panel kit will cost around £4,000-5,000. According to the Energy Saving Trust, a home in the South East of England where most occupants are out all day until 6pm would save around £100 a year on their electricity bills. That means that you wouldn’t break even until 40 years, but solar panels last around 25 years on average. However, if you have your solar panels installed by an MCS-registered installer and they cost £4,500, you could save £220 a year including your SEG payments. That brings the payback time to around 20 years.

So although the initial outlay is slightly less when you install solar panels yourself, it’s much better to have them installed by an MCS-registered engineer so you can take advantage of the SEG payments.

Solar thermal panels are panels that can be used to heat your hot water. The collectors, which are either evacuated tube panels or flat plate collectors, harness heat from the sun and transfer it to a heat transfer liquid that heats up water that is stored in a hot water cylinder. You can use a boiler or immersion heater as a back-up in the winter or to heat the water up further to reach the right temperature.

Evacuated tube panels involve a bank of glass tubes mounted on the roof tiles, and while they’re usually more expensive, they’re more efficient than flat plate collectors. They’re exactly what they sound like – flat panels that can be fixed onto your roof tiles or integrated into the roof.

Having a solar thermal system will reduce your energy bills since heat from the sun is free, so you won’t have to rely on your traditional heating as much. You’ll also be doing your bit for the environment – if you have a natural gas heating system, you could save up to 295kg of CO2 every year.

Another benefit to solar thermal panels is that you might be eligible for payments through the Renewable Heat Incentive (RHI), which is a Government scheme to encourage people to take up renewable heating technologies. As long as you have your system installed by an MCS-registered installer and you meet a few other requirements, you could receive payments of up to £525 per year for seven years. And since the average solar thermal panel system costs £5,500, you could pay off over half of your system just with these payments. That’s not even considering that you could save up to £60 a year on your energy bills if you have a gas system.