Find a Solar Panel Installer you can trust in Aldeburgh.

Like every other systems in your home, solar hot water systems will require periodic inspections as well as a regular maintenance in order to keep it running as efficiently as it should. Not only that, the various components will also require either repair or replacement from time to time. It’ll also be proactive to take the necessary precautions so as to prevent worrying issues like corrosion, scaling or freezing.

Is it a task you can handle on your own? Well, there are some inspections and maintenance activities you should be able to handle on your own, however, you’ll also require a qualified technician to carry out the more technical or complicated tasks. You should also take note that it may actually be more cost effective to have some systems replaced, shut off or removed completely than having it repaired. Here are some of the essential inspections that should be carried out on solar system components. They include:

✓ Collector soiling. Periodic cleaning of your collectors is important especially in dry and dusty climates.

✓ Plumbing, ductwork and wire connections. Check the pipe connections for fluid leaks. Examine duct connections and seals. Also make sure that all wire connections are tight.

✓ Roof penetrations. Flashing and sealant around the roof penetration should be checked to see that it’s in a good shape.

✓ Collector shading. Check for shading of the collectors on annual basis as this may greatly affect their performance.

✓ Support structures. Examine all bolts and nuts which connects the support structures to the collectors for tightness.

✓ Heat transfer fluids. Anti freeze solutions in liquid solar heating collectors will have to be replaced periodically. And this right here is a task that’s best handled by a licensed technician.

How Many Solar Panels And Batteries To Power A House?

Do you wish to know the number of solar panels and batteries sufficient for a house? Well, this is a frequently asked question in the solar world which would be very difficult to provide an accurate answer. This is basically down to the fact that all homes are unique with different sizes as well as amount of daily energy requirements. As a result, the number of solar panels and batteries needed would be unique to the house in question. However, we’ll consider the varying influencing factors that will go a long way to help calculate the number of panels and batteries needed to power a house.

First and foremost, let’s take a look at the solar panels. You’d have to start here by putting into consideration all household appliances that makes use of power in the house to get a good idea of how many that’ll be needed.

• How Many Watts Is Being Used In The House On A Daily Basis?

To determine this, simply go through your utility bill for kilowatt-hours (kWh). This varies amongst homes and being able to identify your daily average energy usage will assist you in getting your solar needs.

• What Is The Number Of The Peak Sunlight Hours At The House’s Location?

Having in mind that the solar panels only work when under direct sunlight, the first step to determine the peak sunlight hours. Once determined, you can then multiply the figure in hours by the house’s hourly energy usage and divide by the solar panel’s wattage.

Overall for a 1500 square foot house, the number of solar panels that’ll be required should fall around 15 to 18.

Meanwhile for batteries, there are also some factors to be considered to determine the number of batteries that is required to power a house. These factors include the house’s power or electricity usage, the period of time in which the battery will be used as well as the battery’ specifications.

Yes – solar panels do work in winter. Contrary to popular belief, solar panels can still work under daylight, even if it's not hot. Of course, they won’t generate as much electricity as they would during the summer months, as the days are shorter, but they will still generate electricity during those daylight hours.

Once you know how solar panels work, it’s easy to understand why solar panels work in the winter. Solar panels are made up of photovoltaic (PV) cells, which are units usually made out of silicon. These cells contain electrons that create energy when light hits them. The cell can then convert this energy into usable electric current and into your system to be used around the home.

Although it might seem strange, solar PV cells can actually work better when it’s cold. Too much heat around the cell can cause it to be inefficient, due to the difference in energy between the energy from the sunlight and the electrons in the solar cell. During cold weather, the difference between them is higher, so more

The higher the energy difference between the two sets of energy sources, the more power that the cell can produce when it’s struck by light. Of course, the downside is that there are fewer daylight hours in the winter, so you’ll still see a drop in energy production – but at least you know that your solar panels are still working efficiently. The other thing to bear in mind is that obstructions like snow and lots of cloud cover will impact the amount of electricity your solar panels will produce. Luckily the UK doesn’t get too much heavy snow, so any snow that does settle on the panels will melt quickly. As for cloud cover, even on exceptionally cloudy days your panels will still generate some electricity – just not as much as they would on a clear day.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

Most people want to connect solar panels to a battery when they’re not at home all day to use the electricity they generate, or generate more than they consume over a day. Solar batteries are a great way to maximise the savings on your energy bills since you can use every unit of electricity you generate.

If you want to connect your solar panels to a battery, the best – and safest – way is to ask an MCS-registered company to do it for you. They’ve had lots of training and hold qualifications in handling electricity and installing solar batteries, so they will be able to recommend the best battery for your solar panels and for the among of electricity you use. Some of the brands they might recommend include Tesla, SolarEdge and SolaX, but there are many more to choose from. If you want to send electricity to the grid from your battery to receive Smart Export Guarantee (SEG) payments, it’s also worth leaving installation up to a registered installer. This is because you might not be eligible for payments if your battery wasn’t installed by an MCS-registered company.

However, if you do want to have a go at connecting your solar panels to a battery, it’s worth finding out whether your system is ‘storage ready’. Most relatively new systems will be, since batteries are becoming more commonplace. If your solar panels are storage ready, they will have an inverter that can easily have a battery added to it. If this is the case, then you should be able to buy the solar battery you want and follow the manufacturer's instructions to install it.

But it’s worth remembering that electricity is extremely dangerous when handled improperly. If you don’t get the solar battery connected properly and something goes wrong, it could cause a fire or you could electrocute yourself. If a fire breaks out due to your battery, it’s unlikely that your home insurance company would pay out since you connected the battery yourself. That’s why it’s always worth speaking to a registered installer to install a solar battery storage system for you.

Solar cells , also referred to as photovoltaic cells (PV), absorbs energy from the sun and converts it to generate electricity. This, however, should not be confused with photovoltaic thermal cells or PVT which operates to generate heat for water in homes. Solar cells are linked electrically and also carefully organized into a large frame which is popularly called solar panels. Generally, solar cells are produced or made of silicon semi conductors which works to absorb sunlight and then turn it into electricity for use at a home. A solar panel comprises of either 60 or 72 solar cells which are electrically interconnected in series and parallel and also positioned in between glass and plastic which is then framed.

At present, solar panels incorporated for residential or domestic purposes only possesses the capacity to make use of only about 20 percent of the sunlight they’re able to absorb and convert it to electricity - also called solar efficiency. Available in the market are also a wide range of solar cell available for both industrial and commercial purposes. This type of solar panels have an efficiency rating of about 40 percent which will also automatically make them more costly than the domestic types.

One great thing about the solar industry is the fact that it keeps improving in such a way that raises both its efficiency as well as overall quality. And with further research and development, this is expected to even increase as the years go by. What’s more? As these aspects keep rising, it’s also expected that the solar panels price should be on a decrease. That way, they’ll become available to a wider range of individuals who’ll also like to save money on electricity bills and go greener.