Find a Solar Panel Installer you can trust in West Glamorgan.

If you want to test your solar panel system to see if it’s working properly or just to see what output it’s giving, you can do this using a multimeter to measure current, or amps, and voltage.

Before you start, you’ll need to find the voltage (v) and current (A) ratings of your panel. You should be able to find them on the back of the panel. You should also make sure that it’s a nice clear, sunny day to get the best readings out of your panel. You should also check that it’s safe to be up on your roof!

To measure open circuit voltage, you’ll need to make sure that your solar panel is completely disconnected from your system’s regulator and battery (if you have one). Angle the panel towards the sun, and ensure that your multimeter is set to measure volts. Measure the voltage between the positive and negative terminals by connecting the negative contact on the voltmeter to the negative on the panel and the positive contact on the voltmeter to the positive on the panel.

Then, you can move on to the short circuit current. Follow the same steps as the open circuit voltage, but ensure that your multimeter is set at 10A to start with.

Only try to test your solar panel if it’s safe to do so. If your roof isn’t accessible without scaffolding or specialist equipment, consider speaking to an MCS-registered solar company about your concerns. They may recommend that they come to service your solar panel system.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

How Many Solar Panels And Batteries To Power A House?

Do you wish to know the number of solar panels and batteries sufficient for a house? Well, this is a frequently asked question in the solar world which would be very difficult to provide an accurate answer. This is basically down to the fact that all homes are unique with different sizes as well as amount of daily energy requirements. As a result, the number of solar panels and batteries needed would be unique to the house in question. However, we’ll consider the varying influencing factors that will go a long way to help calculate the number of panels and batteries needed to power a house.

First and foremost, let’s take a look at the solar panels. You’d have to start here by putting into consideration all household appliances that makes use of power in the house to get a good idea of how many that’ll be needed.

• How Many Watts Is Being Used In The House On A Daily Basis?

To determine this, simply go through your utility bill for kilowatt-hours (kWh). This varies amongst homes and being able to identify your daily average energy usage will assist you in getting your solar needs.

• What Is The Number Of The Peak Sunlight Hours At The House’s Location?

Having in mind that the solar panels only work when under direct sunlight, the first step to determine the peak sunlight hours. Once determined, you can then multiply the figure in hours by the house’s hourly energy usage and divide by the solar panel’s wattage.

Overall for a 1500 square foot house, the number of solar panels that’ll be required should fall around 15 to 18.

Meanwhile for batteries, there are also some factors to be considered to determine the number of batteries that is required to power a house. These factors include the house’s power or electricity usage, the period of time in which the battery will be used as well as the battery’ specifications.

Just like other major house improvement projects, some specific requirements must be met to allow for the installation of solar panels on commercial buildings. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Fortunately, the installation of solar panels on commercial buildings may be “permitted development which mean you won’t have to apply to the Local Planning Authority for planning permission. There are, however, some important limits and conditions which must be put into consideration in order to benefit from these permitted development rights. Some of the limitations include:

• The solar panels must be installed on a wall or pitched roof that should project at a maximum of 200mm from the surface of the wall or roof slope.
• Equipment placed on a roof should not be within one metre of the external edge of that roof.
• Equipment mounted on a wall must not be within one metre of a junction of that wall with another wall or with the roof of the building
• If the equipment is on the roof of a building, the capacity for generation of electricity across the entire site must not be more than 1 megawatt.
• In the situation whereby the panels are installed on a flat roof, the highest part of the equipment should not exceed one metre above the highest part of the roof.

In general, obtaining a planning permission is very important and as such, you must discuss your position with your chosen installation company before you proceed.