Find a Window Installer you can trust in Clackmannanshire.

If you’ve got a problem with condensation and don’t have double glazing, you should find that getting new windows will help. Condensation is caused by warm air meeting a cold surface which then turns into water droplets. With two panes of glass, less heat will escape from your home and keep the window warmer, meaning when steam from the bathroom or kitchen touches your windows there should be less condensation.

It depends on a few factors whether a new double glazed window will look different to existing ones. If your existing windows are very old, perhaps 10 years or more, then it’s likely that there will be some small differences.

The first thing to remember is that your double glazing is exposed to the elements as soon as it’s installed. So over time, unless you’re very good at cleaning and maintaining your windows, they’re likely to look a bit dirty. Window frames that are south-facing may also become slightly discoloured from the sun, so if you install a new window right next to it you might notice a difference.

Also, there have been lots of technical advances in windows over the years. If your existing windows are significantly older, you might notice a difference in the handles on openers, and if your existing windows were installed before 2010 they might not have trickle vents, which is an extra strip on the inside of your window to keep air flowing through your home. While it’s not a legal requirement for replacement windows to have trickle vents if the original one didn’t, it’s a good idea to have them installed as they help prevent condensation and mould.

The only truly noticeably different elements to a new double glazed window compared with existing ones are likely to be on the inside, which might not be a problem for you if you only have one window in a room. However, if you know the brand of your existing windows, you can ask your window installer if they can source the same ones. Even if they’ve been updated slightly, the difference should be minimal.

Ultimately the double glazing company you use is responsible for the quality of work and to ensure your windows are of an excellent standard. This is why it’s important to get a warranty and use a Fensa registered installer. If problems emerge within a couple of years then it’s likely the installation was of a poor standard.Contact the double glazing company and have the issue repaired or new windows replaced. This doesn’t matter if you received a discount of free windows as part of the deal. As long as you entered into a contract the company is obliged to restore the windows.

Yes, of course! It’s common for people to replace just one double glazed window. One reason that people want to replace one window is that the sealed unit inside has failed. You’ll know if this has happened because you’ll be able to see condensation on the inside of glass, which gets frustrating because you can’t wipe it away. In this case, you can choose to simply replace the sealed unit or the entire frame, which you might want to do if it’s looking past its best.

When you’re replacing just one double glazed window, if you know the brand of your current windows you could ask your installer if they can source the same ones. This will help to keep them looking as similar as possible, although if your existing windows are very old you may notice some discolouration on the exterior compared to the new one, and locks and trickle vents might look different.

Replacing just one double glazed window shouldn’t take a qualified window fitter long, and could cost as little as £400. If you want to simply replace the sealed unit, that may only cost around £250. You could try to fit a new window yourself, but it’s worth bearing in mind that all replacement windows need to be certified that they’ve been installed to meet building regulations, so you’ll need to apply to your local building control officer who will come and inspect the work then issue a certificate. If you ask an installer who is registered with a self-certification scheme (like FENSA) to fit the window for you, they can issue the certificate themselves when they’ve finished the work.

Most installers will not need you to be at home while they are fitting your windows. It is a good idea to be present though, just in case they have any questions for you and perhaps for your own peace of mind. If you cannot be there, you will need to arrange access to the property and/or agree securing the property at the end of the day.

No matter how big or small a building is, it can only be as good as it’s foundation - and that’s a fact! It all starts from the footing and when it isn’t deep enough, unlike badly installed gutters or gapped hardwood flooring, can make the whole building collapse to the ground. Just like any code recommendations, the depth of the footings of your porch is a parameter that must be complied with and adjusted to suit your local code requirements.

As a rule of thumb, you should always dig below the frost line when excavating your footings. At this depth level, the moisture present in the soil will be frozen. Ultimately, this will help the ground to act as a barrier to insulate the soil below the footing from freezing during the cold months. As a result, in regions where the weather is almost always very cold the depth of your footings is expected to be at least 48 inches. But in areas featuring a warm climate, you may be allowed to install your footings on grade.

In addition, it’s compulsory that your footings must be installed at a minimum depth of 12 inches below unsettled soil. However, if you’re constructing the structure into a steep hill’s side or by the side of a retaining wall, it’s required that you maintain the least distance to grade both vertically and laterally. In the event whereby you need to achieve a good lateral barrier, you’ll need to have your foundation dug a lot deeper compared to if it’s on a flat surface. For a more accurate and updated information, you can consult your local building inspection department to get familiar with the requirements in your area.

To install one small double glazed window, it will take anywhere between two hours and half a day. It will depend on whether one installer is fitting your window or two. And if you’re doing it yourself and don’t have any professional experience, it will take even longer.

When the window fitters arrive, they will make sure they’ve got safe access to the window and move any heavy furniture if they need to. Any good installer will lay down a dust sheet, but it’s a good idea to check that they’ve got one laid down before they start.

The first step any window installer will take is to double check the measurements of the new frame against your existing one. Hopefully it should match up, so then they’ll take the old window out. Then, they’ll insert the new frame into the aperture and bolt it into the concrete. They'll check it with a spirit level to ensure it’s even before moving onto the glass sealed unit.

The installer will place the glass into the aperture, then fit the beads to secure the glass in the frame. They’ll then use silicone and trim on the inside and outside to ensure the window looks perfect. You won’t be able to see where they’ve used sealants or trims because they’ll colour match them so it’s not noticeable. Then, they’ll tidy up all of their tools and the working area and let you know what needs to be done in terms of proving that the window meets building regulations. Most good installers are registered with a self-certification scheme, so will be able to issue a certification once the work is complete.

Did you just purchase a double glazed window and confused about how to have it installed? Fitting the window yourself can be quite easy with the help of this step by step guide. However, if you lack proper training or experience, we’d recommend you reach out to a trustworthy professional who can guarantee the best results for help. That said, now let’s take a look at the process.

• Remove the old windows by detaching the old beading and glass window safely. Then make some interval cuts using a hand saw before using a crowbar to pry it out.

• Cut the external double glazed window seal. Once done, take a measurement of the window area’s width once empty. Then transfer the measurement to the window sil to face outside and cut using a handsaw.

• Seal the window sil. Add a bead of clear silicone along both inside lip as well as the centre to seal the sil.

• Screw the double glazed window to the sil. Position the window on the top of the lipped section that was siliconed. Then pre-drill them together and screw in three places. You should make sure the screws do not go totally to the sil’s bottom.

• Install the double glazed window. After successfully screwing the double glazed window to the sil, you can now fit in the double glazing. Make use of packers to make sure it’s even in the slot.

• Screw the uPVC window to the wall. If you’re happy and satisfied with the position of the window, you can then pre-drill through the frame of the window and the brick wall. Once done, simply screw it in place using masonry screws or Spax screw as they do not require crawl plugs in bricks.

• Seal around the window. To do this, simply fill any gaps with expanding foam, wipe out the excess and seal with silicone.