Find a Window Installer you can trust in Fowey.

On the grand scale of things there isn’t a huge difference between B-rated windows and A-rated windows. Consumer watchdog Which? have calculated an extra 6.5% would be saved on energy bills with A rather than B rated panes. Be aware that A rated windows are slightly more expensive, however.

Tiling a porch roof is a very important but laborious and difficult task. A project of this magnitude will require a large investment in planning and preparation way before the actual installation process takes place. It can be a brand new porch roofing tile or a replacement of the existing one, either way it’s crucial to get the right technique. If you lack proper training or experience in this field, we’d recommend you hire the services of a reliable professional probably within your local area to guarantee the best results and to save yourself some time and money. This guide will give you a good insight into the porch roof tiling process. Let’s have a look!

• With the crown looking upwards, put the first tile on the batten and centre the tile from side to side.

• Hammer a 10d nail at the base of the tile and into the batten (make sure not to overdrive the nail).

• To provide a much needed support, apply a little mortar under the first tile.

• Identify the inner end of the first tile and place another tile on top. Take a measurement from the outer end and adjust the end of the second tile to fit.

• Just like you’ve done with the first tile, nail the second tile into the batten.

• Position two tiles at the both ends of the ridge and proceed with the installation just as you’ve done with the previous tiles.

• Take a measurement of the distance across the ridge from the first tile’s outer end. Once done, you can then calculate the number of tiles required by subtracting 16 inches from your measurement and divide the answer by 8.

• Beginning at the second tile on one end of the ridge, install the half the number of ridge tiles towards the centre of the ridge. Now install the remaining tiles working from the opposite end to the ridge’s centre. At the centre of ridge should be a key tile with mortar.

Are you looking to replace your old window for a new double glazed window and wondering what it’s going to be the cost? Well, the double glazed windows market is a very competitive one in the UK with varying prices across the country. Therefore, if you shop around you’re most likely to find something that’ll fit your budget both products and quality wise.

As you would have expected, the more windows you required the more money you are going to spend. However, the cost per window is likely going to be lower depending on the number of windows you purchase. Several double glazed windows come with a 10 year warranty but it’s advisable to also obtain a solid workmanship warranty which provides coverage for any potential problems for a good period of time upon installation.

To determine the cost of double glazed windows, there are so many things to put into consideration that just the primary dimensions of the window itself. Other factors that works to decrease or increase the cost of the project includes the frames’ quality as well as the material used. For example hardwood can be quite high priced when compared to uPVC.

The number of opening windows within the frame can also play a huge role in the cost of the windows as well as the type of the glass. The cost of a double glazing window usually ranges between £100 to £3,200 per window, depending on the available options.

To have a more accurate estimate of the cost of a double glazing window, you’ll need a obtain a survey from a double glazing installer who can take into account any possible complications that may arise when installing your windows while also giving an advise on the most suitable window style for your property.

No matter how big or small a building is, it can only be as good as it’s foundation - and that’s a fact! It all starts from the footing and when it isn’t deep enough, unlike badly installed gutters or gapped hardwood flooring, can make the whole building collapse to the ground. Just like any code recommendations, the depth of the footings of your porch is a parameter that must be complied with and adjusted to suit your local code requirements.

As a rule of thumb, you should always dig below the frost line when excavating your footings. At this depth level, the moisture present in the soil will be frozen. Ultimately, this will help the ground to act as a barrier to insulate the soil below the footing from freezing during the cold months. As a result, in regions where the weather is almost always very cold the depth of your footings is expected to be at least 48 inches. But in areas featuring a warm climate, you may be allowed to install your footings on grade.

In addition, it’s compulsory that your footings must be installed at a minimum depth of 12 inches below unsettled soil. However, if you’re constructing the structure into a steep hill’s side or by the side of a retaining wall, it’s required that you maintain the least distance to grade both vertically and laterally. In the event whereby you need to achieve a good lateral barrier, you’ll need to have your foundation dug a lot deeper compared to if it’s on a flat surface. For a more accurate and updated information, you can consult your local building inspection department to get familiar with the requirements in your area.

Most window installers will be able to provide you with one double glazed window and fit it for you. If you’re replacing one double glazed window in your home, ask them to try and source the same windows that you already have or find one that’s very similar. Externally, you probably won’t be able to notice the difference, but if your existing windows are very old there may be some exterior discolouration and the locks and handles might look slightly different.

If you want one double glazed window so you can fit it yourself, there are lots of online companies that can supply you with one window. However, window fitting is a skilled trade and you might want to consider whether you have the right tools and experience to fit it yourself. Of course, you’ll save money on installation costs, but if something goes wrong, you might end up shelling out to get it fixed anyway.

The other thing to consider is that any replacement windows need to be certified that they meet Building Regulations. If you fit the double glazed window yourself, you’ll need to apply to your local council building control officer to get a certificate that confirms that you fitted the window within the regulations. You’ll have to pay a fee for this, and it will be even more expensive if Building Control say that the window hasn’t been fitted within the regulations and you have to start again.

The alternative is to ask a reputable window installer that is registered with a self-certification scheme, like FENSA, to install the window. That means that they can self-certify that the window meets building regulations once they’ve finished the installation.

uPVC is unplasticised polyvinyl chloride. It is a favourite amongst homeowners and manufacturers for its cheap production cost and excellent benefits. uPVC is used for window frames, conservatories and doors. In fact, uPVC can be three times cheaper than wooden frames and is also the most energy efficient option.As well as this, uPVC is now available in a range of colours other than the typically seen bright white finish. It can also be recycled, is durable and resistant to changing weather conditions.

• The glass has smashed from an impact such as a stone hitting it from a lawnmower
• You have been broken into and suspects used the window to gain entry
• The glass has blown (lost its airtightness) from constant water build-up around the seals, which is common in bathrooms
• Extreme weather or pressure changes have caused a crack

1. Including the beading (the plastic and rubber seals around the windows that can be removed), measure the width of the window frame.
2. Do the same for the height of the window, making sure you include the beading.
3. Then, take 10mm off each measurement, and you have the approximate size of your glass.