Find a Window Installer you can trust in Fairford.

As well as keeping your home warmer and reducing noise, you’ll notice a saving on your energy bills from installing double glazing. If you install A++ rated windows in your home after having single glazing, you could save up to £120 year on your energy bills. The Energy Saving Trust has more information.

On the grand scale of things there isn’t a huge difference between B-rated windows and A-rated windows. Consumer watchdog Which? have calculated an extra 6.5% would be saved on energy bills with A rather than B rated panes. Be aware that A rated windows are slightly more expensive, however.

Tiling a porch roof is a very important but laborious and difficult task. A project of this magnitude will require a large investment in planning and preparation way before the actual installation process takes place. It can be a brand new porch roofing tile or a replacement of the existing one, either way it’s crucial to get the right technique. If you lack proper training or experience in this field, we’d recommend you hire the services of a reliable professional probably within your local area to guarantee the best results and to save yourself some time and money. This guide will give you a good insight into the porch roof tiling process. Let’s have a look!

• With the crown looking upwards, put the first tile on the batten and centre the tile from side to side.

• Hammer a 10d nail at the base of the tile and into the batten (make sure not to overdrive the nail).

• To provide a much needed support, apply a little mortar under the first tile.

• Identify the inner end of the first tile and place another tile on top. Take a measurement from the outer end and adjust the end of the second tile to fit.

• Just like you’ve done with the first tile, nail the second tile into the batten.

• Position two tiles at the both ends of the ridge and proceed with the installation just as you’ve done with the previous tiles.

• Take a measurement of the distance across the ridge from the first tile’s outer end. Once done, you can then calculate the number of tiles required by subtracting 16 inches from your measurement and divide the answer by 8.

• Beginning at the second tile on one end of the ridge, install the half the number of ridge tiles towards the centre of the ridge. Now install the remaining tiles working from the opposite end to the ridge’s centre. At the centre of ridge should be a key tile with mortar.

Using a Fensa registered installer isn’t compulsory but it helps to protect you from cowboys and rogue traders. It will also make life a whole lot easier in regards to Building Regulations. Replacement windows must meet a certain energy efficiency rating and once fitted you need a certificate to show your installation complies. By using a Fensa registered company they’ll issue this certificate, otherwise you’ll need the council to look at the new windows.

Double glazed windows are better than single glazed generally because they are more energy efficient. The clue’s in the name – double glazed windows have two panes of glass while single glazed windows only have one. In double glazed windows, there is a space between the two glass panes. This space is filled with inert gas or a tight vacuum, which helps to provide an extra level of insulation. That means that heat won’t escape your home easily, nor will it creep in, so you can keep your home at a more comfortable temperature.

The extra pane of glass also helps to increase your home’s security. Single glazing is pretty easy to smash through, whereas it will take much more effort to smash double glazing and will create more noise, so burglars might be put off.

Another reason why double glazed windows are better than single glazed ones is that they help to reduce noise. Of course, if you live by a busy road you’ll still hear some traffic noise, but it can be significantly reduced buy double glazing. In the same way that the inert gas in the middle of the two panes keeps heat in and the cold out, it also helps keep noise out.

With double glazing, you’ll also notice much less condensation. With single glazing, it’s common to see condensation on the inside of the windows, especially when the heating is on. This is because the outside of the window is cold, but the inside is warm. With double glazing, the insulation between the two panes stops there being such a difference in temperature between the inside and outside of the window.

The energy efficiency of windows is measured using ratings, varying from A, the most efficient, to G, the least efficient. This scheme is run by the British Fenestration Council (BFRC). To comply with Building Regulations you’ll need windows of energy efficiency at least level C.

No matter how big or small a building is, it can only be as good as it’s foundation - and that’s a fact! It all starts from the footing and when it isn’t deep enough, unlike badly installed gutters or gapped hardwood flooring, can make the whole building collapse to the ground. Just like any code recommendations, the depth of the footings of your porch is a parameter that must be complied with and adjusted to suit your local code requirements.

As a rule of thumb, you should always dig below the frost line when excavating your footings. At this depth level, the moisture present in the soil will be frozen. Ultimately, this will help the ground to act as a barrier to insulate the soil below the footing from freezing during the cold months. As a result, in regions where the weather is almost always very cold the depth of your footings is expected to be at least 48 inches. But in areas featuring a warm climate, you may be allowed to install your footings on grade.

In addition, it’s compulsory that your footings must be installed at a minimum depth of 12 inches below unsettled soil. However, if you’re constructing the structure into a steep hill’s side or by the side of a retaining wall, it’s required that you maintain the least distance to grade both vertically and laterally. In the event whereby you need to achieve a good lateral barrier, you’ll need to have your foundation dug a lot deeper compared to if it’s on a flat surface. For a more accurate and updated information, you can consult your local building inspection department to get familiar with the requirements in your area.

Are you about to purchase a double glazed unit and wondering how to go about the replacement project? If yes, then you’re at the right place. Firstly, it’s advisable to hire the services of a reliable professional who can guarantee the best results for help especially if you lack proper training and experience in the field. However, we’ve put together this step by step guide to provide you with a detailed information about the double glazed unit replacement process. Let’s get started!

The tools and materials you require for the project includes tape measure, hammers, nail punch, scraper, spacing blocks, non-hardening butyl putty, high-security glazing tape rolls and beading tacks.

• Work out the glass size required. Simply use the tape measure to measure from frame edge to frame edge while also taking note of the thickness.

• When about to order, inform the glass merchant that the measurement provided are frame-tight. This will make him reduce the dimension a little bit, mostly by 5mm for clearance.

• Remove the beading and ensure to support the glass while doing so. If the glass units are fitted in wooden windows, you may need to cut the putty-based compound they’re normally sealed with to remove the glass.

• Lay out the beading in the window’s shape to make for easier refitting later on.

• If you’re working on wooden frames, wipe out all traces of excess installation compound using a scraper and clean the rebate with a soft brush.

• Trial fit the double glazed windows to ensure they’d slide into the frame without being forced.

• Plastic frame windows are usually in between a pair of gaskets, you should replace this with a hight security glazing tape. While for a wooden frame, simply apply strips of flexible non-setting butyl putty or high-security glazing tape on either sides of the glass.

• Install and centralize the glass in the frame.

• Press the nail wooden beading or plastic beading back into place.