Find a Window Installer you can trust in Bangor.

These days, buyers expect homes to have double glazing. People recognise the benefits of installing double glazing, so if you don’t have it installed you should consider it. You’ll increase your property’s value and give it a better chance of selling faster, since single glazed properties are also more likely to have problems with damp and mould which could put buyers off.

Some properties are unable to have double glazing, especially those in conservation areas or listed buildings. To counter this problem and still benefit from a warmer home and cheaper bills, secondary glazing is an option. Secondary glazing is a second pane fitted inside your original window. Secondary glazing will still save you around £105 yearly.

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

Are you about to purchase a double glazed unit and wondering how to go about the replacement project? If yes, then you’re at the right place. Firstly, it’s advisable to hire the services of a reliable professional who can guarantee the best results for help especially if you lack proper training and experience in the field. However, we’ve put together this step by step guide to provide you with a detailed information about the double glazed unit replacement process. Let’s get started!

The tools and materials you require for the project includes tape measure, hammers, nail punch, scraper, spacing blocks, non-hardening butyl putty, high-security glazing tape rolls and beading tacks.

• Work out the glass size required. Simply use the tape measure to measure from frame edge to frame edge while also taking note of the thickness.

• When about to order, inform the glass merchant that the measurement provided are frame-tight. This will make him reduce the dimension a little bit, mostly by 5mm for clearance.

• Remove the beading and ensure to support the glass while doing so. If the glass units are fitted in wooden windows, you may need to cut the putty-based compound they’re normally sealed with to remove the glass.

• Lay out the beading in the window’s shape to make for easier refitting later on.

• If you’re working on wooden frames, wipe out all traces of excess installation compound using a scraper and clean the rebate with a soft brush.

• Trial fit the double glazed windows to ensure they’d slide into the frame without being forced.

• Plastic frame windows are usually in between a pair of gaskets, you should replace this with a hight security glazing tape. While for a wooden frame, simply apply strips of flexible non-setting butyl putty or high-security glazing tape on either sides of the glass.

• Install and centralize the glass in the frame.

• Press the nail wooden beading or plastic beading back into place.

The energy efficiency of windows is measured using ratings, varying from A, the most efficient, to G, the least efficient. This scheme is run by the British Fenestration Council (BFRC). To comply with Building Regulations you’ll need windows of energy efficiency at least level C.

Removing a double glazed window can be quite labour intensive. If you decide to try it yourself, make sure you give yourself plenty of time, and wear gloves and goggles.

Begin by unscrewing all opening windows at the hinges and removing them. Then take away the beading and putty around any fixed panes and take them out too.

Once you’ve removed all the glass, use a saw to put angled cuts in the frame, and a bar and hammer to remove it in sections. You should remove the sill if you’re going to replace that too.

Finally, cut through any screws holding the frame into place with a hacksaw.

Yes, of course! It’s common for people to replace just one double glazed window. One reason that people want to replace one window is that the sealed unit inside has failed. You’ll know if this has happened because you’ll be able to see condensation on the inside of glass, which gets frustrating because you can’t wipe it away. In this case, you can choose to simply replace the sealed unit or the entire frame, which you might want to do if it’s looking past its best.

When you’re replacing just one double glazed window, if you know the brand of your current windows you could ask your installer if they can source the same ones. This will help to keep them looking as similar as possible, although if your existing windows are very old you may notice some discolouration on the exterior compared to the new one, and locks and trickle vents might look different.

Replacing just one double glazed window shouldn’t take a qualified window fitter long, and could cost as little as £400. If you want to simply replace the sealed unit, that may only cost around £250. You could try to fit a new window yourself, but it’s worth bearing in mind that all replacement windows need to be certified that they’ve been installed to meet building regulations, so you’ll need to apply to your local building control officer who will come and inspect the work then issue a certificate. If you ask an installer who is registered with a self-certification scheme (like FENSA) to fit the window for you, they can issue the certificate themselves when they’ve finished the work.

You don’t have to, especially if you’re on a budget. If you’re only replacing some, it’s a good idea to get all the windows on one side of your property replaced at the same time, so they all look the same. Be aware, obviously, huge savings could be had by having a number of windows replaced at the same time.