Find a Window Installer you can trust in Criccieth.

Using a Fensa registered installer isn’t compulsory but it helps to protect you from cowboys and rogue traders. It will also make life a whole lot easier in regards to Building Regulations. Replacement windows must meet a certain energy efficiency rating and once fitted you need a certificate to show your installation complies. By using a Fensa registered company they’ll issue this certificate, otherwise you’ll need the council to look at the new windows.

Removing a double glazed window can be quite labour intensive. If you decide to try it yourself, make sure you give yourself plenty of time, and wear gloves and goggles.

Begin by unscrewing all opening windows at the hinges and removing them. Then take away the beading and putty around any fixed panes and take them out too.

Once you’ve removed all the glass, use a saw to put angled cuts in the frame, and a bar and hammer to remove it in sections. You should remove the sill if you’re going to replace that too.

Finally, cut through any screws holding the frame into place with a hacksaw.

• Climate - If your window faces south, it will be subject to direct sunlight for a lot of the day. This tends to cause the sealed unit to fail more quickly – a south-facing window may last between 10-25 years. This is because the spacer bars will twist as the temperature rises and causes the adhesive holding them together to eventually fail.
• Moisture - Windows in kitchens and bathrooms tend to fail more quickly because they come into contact with moisture more often. For example, if water gets on your windowsill when you shower, the seal around the glass will come loose more quickly if it’s constantly wet.

Unfortunately, you can’t fix the glass on one side of a double glazed window. That’s because they’re sealed units – once one pane of glass is broken, that will break the seal and its thermal insulation properties will be lost.

The good news is that if your window frame is still looking great, there’s no need to replace that. You can simply replace the glass in the window, which will cost much less. You can look to spend around £250 on a sealed unit, whereas a whole replacement single window may cost up to £600.

When an installer comes to replace the glass in your double glazed window, they will survey the inside and outside of your home around the window, then move any furniture by the window so they’ve got access. They should then pop a dust sheet down to stop any debris from getting on your floor.

Then, the installer will carefully remove the beads from the frame. They will then lift the glass out of the frame and put it somewhere safe before cleaning out all of the dust and any debris that has found its way into the frame. Using spacers at the bottom of the frame, the installer will make sure that the sealed unit is square in the frame to get a good fit. Once they’re happy, they will replace the beading and make sure it looks perfect before cleaning up their tools.

You could have a go at replacing the glass on a double glazed window yourself, but it’s not recommended. Leave it to the professionals who will know exactly what to do and will be able to do it quickly and safely.

Did you just purchase a double glazed window and confused about how to have it installed? Fitting the window yourself can be quite easy with the help of this step by step guide. However, if you lack proper training or experience, we’d recommend you reach out to a trustworthy professional who can guarantee the best results for help. That said, now let’s take a look at the process.

• Remove the old windows by detaching the old beading and glass window safely. Then make some interval cuts using a hand saw before using a crowbar to pry it out.

• Cut the external double glazed window seal. Once done, take a measurement of the window area’s width once empty. Then transfer the measurement to the window sil to face outside and cut using a handsaw.

• Seal the window sil. Add a bead of clear silicone along both inside lip as well as the centre to seal the sil.

• Screw the double glazed window to the sil. Position the window on the top of the lipped section that was siliconed. Then pre-drill them together and screw in three places. You should make sure the screws do not go totally to the sil’s bottom.

• Install the double glazed window. After successfully screwing the double glazed window to the sil, you can now fit in the double glazing. Make use of packers to make sure it’s even in the slot.

• Screw the uPVC window to the wall. If you’re happy and satisfied with the position of the window, you can then pre-drill through the frame of the window and the brick wall. Once done, simply screw it in place using masonry screws or Spax screw as they do not require crawl plugs in bricks.

• Seal around the window. To do this, simply fill any gaps with expanding foam, wipe out the excess and seal with silicone.

If you’ve decided to construct a porch to your property and now looking to figure out the cost required to complete the project, then you’re at the right place!

There are many factors that comes to play when determining the price of building a porch. These factors includes the size of the porch, the number of windows, the style of the roof as well as the type of the porch selected. Now let’s take a look at these factors one after the other.

• The Porch’s Size

As you would have correctly imagined, a large porch will definitely cost more money than a smaller one. A rough estimate of a porch’s cost per square metre is approximately £1,400.

• The Number Of Windows

Just like in the scenario above, the more the number of windows to be incorporated, the more money you’ll have to pay to complete your porch. A porch window will generally cost you within a range of £300 to £1,000

• The Style Of The Roof

There are two popular styles of porch’s roof which includes a tiled rood and a rubber flat roof. Generally, roof tiles are costlier than a rubber flat roof. A tiled roof would cost you between £0.80 to £1.80 per roof tile, while a rubber roofing will cost your between £70 to £90 per metre squared.

• Type Of The Porch

Another huge determinant of a porch’s price is type of material incorporated. For instance, if your preferred type is a lean-to, the price of a uPVC would be between £2,300 to £2,700. Meanwhile, a flat gable roof porch should cost within a range of £3,300 to £3,800.

Kindly note that the costs quoted in this article are only rough estimates, for a more accurate estimate you can contact a porch building professional within your local area.

Double glazing is made up of two layers of glass, with a layer of argon gas in between. This type of glass can be used in Aluminium windows. The gas is a poor insulator, helping heat to stay in your home and making your windows more efficient. As well as trapping the argon gas, the second layer of glass reduces the amount of noise that enters your property, and helps to make your windows stronger and more secure.