Find a Window Installer you can trust in Lancashire.

Accidents happen, and sometimes windows get broken. And that will lead to you wanting to replace just the glass in your window, rather than the whole frame. Also, as windows get older they can mist up on the inside, which means that the unit has ‘blown’ - so you’ll also need to replace the glass. But how much is it to replace the glass in a window? Luckily, if the frame of your window is in good condition, there’s no need to replace it, and this will reduce the cost. For an installer to fit a new pane of glass in a single glazed window, the average cost is £100, while a replacement double glazed sealed unit will cost an average of £110. Of course, as this is an average, if your window is very large you may spend more, and if your window is very small the price may be less. That's why it’s important to get a range of quotes so you can compare costs and get the best price. If you’re good at DIY, you may feel confident enough to have a go at replacing the glass in your window yourself. In that case, the cost of sealed unit and any other materials you need will cost an average of £57. It’s a significant saving, and if you think you can do it, then give it a try. However, if you’re in any way unsure, it’s best to leave it to the professionals. A window installer will be able to replace the glass in your window in less than an hour. Even though it costs more for a professional to do it, if you get it wrong and have to start over it will cost you more in the long run.

Just like every other thing in your house, your double glazed windows have an expected lifespan attached to it as it gradually becomes less functional and less efficient over time. Although there are actually top quality windows which are able to last a very long time, but the fact still remains that nothing can stand the test of time or last forever. Even the best quality double glazed windows will eventually need to be replaced at some point. So exactly how long do double glazing windows last before need a replacement?

To make it brief, most double glazing window units are typically expected to last an average of 20 years. This number of years can, however, vary within the range of 10 to 35 years based on the several factors such as the type, quality of materials as well as installation and where the windows are located.

The reason for the depreciation in double glazing windows is, over time, the windows may be subjected to some wear, tear as well as all kinds of minor damages which includes gas filled insulated glazing unit slowly and gradually leaking. According to the Centre for Sustainable Energy, the evaporation of 25 percent of gas will ultimately minimize the windows’ thermal performance. And when this occurs, fitting a secondary glazing measure or replacing the windows should be put into consideration.

Another factor leading to the gradual depreciation in double glazing windows over time has to do with condensation. When the window collects between the layers of glass due to the failure of the seal of the perimeter and the saturation of the desiccant, can only be solved by IGU replacement.

And finally, the ravages of time also has a way of taking its toll on double glazing windows. This can happen in so many ways such that the window becomes a lot less efficient and later needing to be replaced.

As well as keeping your home warmer and reducing noise, you’ll notice a saving on your energy bills from installing double glazing. If you install A++ rated windows in your home after having single glazing, you could save up to £120 year on your energy bills. The Energy Saving Trust has more information.

To install one small double glazed window, it will take anywhere between two hours and half a day. It will depend on whether one installer is fitting your window or two. And if you’re doing it yourself and don’t have any professional experience, it will take even longer.

When the window fitters arrive, they will make sure they’ve got safe access to the window and move any heavy furniture if they need to. Any good installer will lay down a dust sheet, but it’s a good idea to check that they’ve got one laid down before they start.

The first step any window installer will take is to double check the measurements of the new frame against your existing one. Hopefully it should match up, so then they’ll take the old window out. Then, they’ll insert the new frame into the aperture and bolt it into the concrete. They'll check it with a spirit level to ensure it’s even before moving onto the glass sealed unit.

The installer will place the glass into the aperture, then fit the beads to secure the glass in the frame. They’ll then use silicone and trim on the inside and outside to ensure the window looks perfect. You won’t be able to see where they’ve used sealants or trims because they’ll colour match them so it’s not noticeable. Then, they’ll tidy up all of their tools and the working area and let you know what needs to be done in terms of proving that the window meets building regulations. Most good installers are registered with a self-certification scheme, so will be able to issue a certification once the work is complete.

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

Whether you’re hiring a professional to replace your double glazing or are considering DIY, it’s a good idea to know how to fit a double glazed window.

You need to start by assembling your window. Fit any handles and cut the outer sill to size by measuring the outer wall depth. Then, screw the outer sill to the window frame and attach the frame fixers. Screw the ventilation grilles onto the inside of the frame and fix the vents on.

Next, you need put the window into place, using spacers to wedge it in. Use a spirit level to check it’s level horizontally and vertically, adding extra spacers if needed. Then, fix the frame into place at each fixing point using a drill, wall plugs and screws. Measure and cut the interior sill, and check that it’s level, adding spacers if needed. Then fix it using screws, masonry nails or adhesive.

Finally, fill in any wide gaps with foam filler and small gaps with sealant. You can get interior and exterior trims to cover these up, making your window look neat and professional.

After fitting your new windows, your installer should take away and dispose of your old windows. If you want to keep them, just let your installer know before they start work. The UPVC frames are melted down and used on the unseen parts of new windows. Aluminium frames are re-smelted and wooden are broken down and used as chipboard.

Are you about to purchase a double glazed unit and wondering how to go about the replacement project? If yes, then you’re at the right place. Firstly, it’s advisable to hire the services of a reliable professional who can guarantee the best results for help especially if you lack proper training and experience in the field. However, we’ve put together this step by step guide to provide you with a detailed information about the double glazed unit replacement process. Let’s get started!

The tools and materials you require for the project includes tape measure, hammers, nail punch, scraper, spacing blocks, non-hardening butyl putty, high-security glazing tape rolls and beading tacks.

• Work out the glass size required. Simply use the tape measure to measure from frame edge to frame edge while also taking note of the thickness.

• When about to order, inform the glass merchant that the measurement provided are frame-tight. This will make him reduce the dimension a little bit, mostly by 5mm for clearance.

• Remove the beading and ensure to support the glass while doing so. If the glass units are fitted in wooden windows, you may need to cut the putty-based compound they’re normally sealed with to remove the glass.

• Lay out the beading in the window’s shape to make for easier refitting later on.

• If you’re working on wooden frames, wipe out all traces of excess installation compound using a scraper and clean the rebate with a soft brush.

• Trial fit the double glazed windows to ensure they’d slide into the frame without being forced.

• Plastic frame windows are usually in between a pair of gaskets, you should replace this with a hight security glazing tape. While for a wooden frame, simply apply strips of flexible non-setting butyl putty or high-security glazing tape on either sides of the glass.

• Install and centralize the glass in the frame.

• Press the nail wooden beading or plastic beading back into place.