Find a Window Installer you can trust in Rushden.

It depends on a few factors whether a new double glazed window will look different to existing ones. If your existing windows are very old, perhaps 10 years or more, then it’s likely that there will be some small differences.

The first thing to remember is that your double glazing is exposed to the elements as soon as it’s installed. So over time, unless you’re very good at cleaning and maintaining your windows, they’re likely to look a bit dirty. Window frames that are south-facing may also become slightly discoloured from the sun, so if you install a new window right next to it you might notice a difference.

Also, there have been lots of technical advances in windows over the years. If your existing windows are significantly older, you might notice a difference in the handles on openers, and if your existing windows were installed before 2010 they might not have trickle vents, which is an extra strip on the inside of your window to keep air flowing through your home. While it’s not a legal requirement for replacement windows to have trickle vents if the original one didn’t, it’s a good idea to have them installed as they help prevent condensation and mould.

The only truly noticeably different elements to a new double glazed window compared with existing ones are likely to be on the inside, which might not be a problem for you if you only have one window in a room. However, if you know the brand of your existing windows, you can ask your window installer if they can source the same ones. Even if they’ve been updated slightly, the difference should be minimal.

• Climate - If your window faces south, it will be subject to direct sunlight for a lot of the day. This tends to cause the sealed unit to fail more quickly – a south-facing window may last between 10-25 years. This is because the spacer bars will twist as the temperature rises and causes the adhesive holding them together to eventually fail.
• Moisture - Windows in kitchens and bathrooms tend to fail more quickly because they come into contact with moisture more often. For example, if water gets on your windowsill when you shower, the seal around the glass will come loose more quickly if it’s constantly wet.

How long your aluminium windows will last depends on their quality. They should last 20 -30 years at least, but have been known to stay in good condition for up to 45 years. This is considerably longer than uPVC and wooden double glazing.

Double glazing frames don’t just have to come in uPVC and are available in other materials including aluminium and wood too. Wooden or timber windows are more suited to properties with a traditional look and are often the frame of choice for listed buildings and homes in conservation areas. When properly maintained wooden windows can last well for years but can be up to three times more expensive than uPVC.Aluminium is the strongest and most durable option. As a metal it is highly resistant to the UK’s changing weather conditions and won’t rust, warp, crack or peel. Aluminium offers a modern appeal and is available in a range of colours.

Did you just purchase a double glazed window and confused about how to have it installed? Fitting the window yourself can be quite easy with the help of this step by step guide. However, if you lack proper training or experience, we’d recommend you reach out to a trustworthy professional who can guarantee the best results for help. That said, now let’s take a look at the process.

• Remove the old windows by detaching the old beading and glass window safely. Then make some interval cuts using a hand saw before using a crowbar to pry it out.

• Cut the external double glazed window seal. Once done, take a measurement of the window area’s width once empty. Then transfer the measurement to the window sil to face outside and cut using a handsaw.

• Seal the window sil. Add a bead of clear silicone along both inside lip as well as the centre to seal the sil.

• Screw the double glazed window to the sil. Position the window on the top of the lipped section that was siliconed. Then pre-drill them together and screw in three places. You should make sure the screws do not go totally to the sil’s bottom.

• Install the double glazed window. After successfully screwing the double glazed window to the sil, you can now fit in the double glazing. Make use of packers to make sure it’s even in the slot.

• Screw the uPVC window to the wall. If you’re happy and satisfied with the position of the window, you can then pre-drill through the frame of the window and the brick wall. Once done, simply screw it in place using masonry screws or Spax screw as they do not require crawl plugs in bricks.

• Seal around the window. To do this, simply fill any gaps with expanding foam, wipe out the excess and seal with silicone.

uPVC is unplasticised polyvinyl chloride. It is a favourite amongst homeowners and manufacturers for its cheap production cost and excellent benefits. uPVC is used for window frames, conservatories and doors. In fact, uPVC can be three times cheaper than wooden frames and is also the most energy efficient option.As well as this, uPVC is now available in a range of colours other than the typically seen bright white finish. It can also be recycled, is durable and resistant to changing weather conditions.

You can only repair blown double glazed windows in the sense that you can replace the sealed unit (the glass part of the window) instead of having to replace the entire window.

When a double glazed window is blown, it means that the seal around the window has failed and is now letting air in and out. Often the first sign that the sealed unit has blown is condensation on the inside of the window, which is annoying since there’s no way to get rid of it! When your sealed unit has blown, you’ll be losing heat out of the window, meaning you could be spending more on your energy bills.

As a temporary fix, you could see if you can buy a misting repair kit online, but the condensation will eventually occur again as the air gets in. The best thing to do is ask a window installer or glazier to replace the sealed unit for you.

It's simple to replace the glass in a window – the specialist will remove the beading around the window, remove the blown glass from your window frame and set it to one side. They will then clean up around the frame before adding spacers in, then fitting the new sealed unit into the frame. They’ll make sure it’s a snug fit before replacing the beading back around the window to secure it.

There's no reason to put off repairing a blown double glazed window since the cost is generally much less than replacing the entire thing. A sealed unit with installation costs an average of £100, whereas a completely new window will cost around £400. You’ll soon notice that it’s less draughty and will be able see out of your window once you’ve had the blown glass replaced.

Some properties are unable to have double glazing, especially those in conservation areas or listed buildings. To counter this problem and still benefit from a warmer home and cheaper bills, secondary glazing is an option. Secondary glazing is a second pane fitted inside your original window. Secondary glazing will still save you around £105 yearly.