Find a Window Installer you can trust in Thame.

Yes, of course! It’s common for people to replace just one double glazed window. One reason that people want to replace one window is that the sealed unit inside has failed. You’ll know if this has happened because you’ll be able to see condensation on the inside of glass, which gets frustrating because you can’t wipe it away. In this case, you can choose to simply replace the sealed unit or the entire frame, which you might want to do if it’s looking past its best.

When you’re replacing just one double glazed window, if you know the brand of your current windows you could ask your installer if they can source the same ones. This will help to keep them looking as similar as possible, although if your existing windows are very old you may notice some discolouration on the exterior compared to the new one, and locks and trickle vents might look different.

Replacing just one double glazed window shouldn’t take a qualified window fitter long, and could cost as little as £400. If you want to simply replace the sealed unit, that may only cost around £250. You could try to fit a new window yourself, but it’s worth bearing in mind that all replacement windows need to be certified that they’ve been installed to meet building regulations, so you’ll need to apply to your local building control officer who will come and inspect the work then issue a certificate. If you ask an installer who is registered with a self-certification scheme (like FENSA) to fit the window for you, they can issue the certificate themselves when they’ve finished the work.

The energy efficiency of windows is measured using ratings, varying from A, the most efficient, to G, the least efficient. This scheme is run by the British Fenestration Council (BFRC). To comply with Building Regulations you’ll need windows of energy efficiency at least level C.

It depends on a few factors whether a new double glazed window will look different to existing ones. If your existing windows are very old, perhaps 10 years or more, then it’s likely that there will be some small differences.

The first thing to remember is that your double glazing is exposed to the elements as soon as it’s installed. So over time, unless you’re very good at cleaning and maintaining your windows, they’re likely to look a bit dirty. Window frames that are south-facing may also become slightly discoloured from the sun, so if you install a new window right next to it you might notice a difference.

Also, there have been lots of technical advances in windows over the years. If your existing windows are significantly older, you might notice a difference in the handles on openers, and if your existing windows were installed before 2010 they might not have trickle vents, which is an extra strip on the inside of your window to keep air flowing through your home. While it’s not a legal requirement for replacement windows to have trickle vents if the original one didn’t, it’s a good idea to have them installed as they help prevent condensation and mould.

The only truly noticeably different elements to a new double glazed window compared with existing ones are likely to be on the inside, which might not be a problem for you if you only have one window in a room. However, if you know the brand of your existing windows, you can ask your window installer if they can source the same ones. Even if they’ve been updated slightly, the difference should be minimal.

On the grand scale of things there isn’t a huge difference between B-rated windows and A-rated windows. Consumer watchdog Which? have calculated an extra 6.5% would be saved on energy bills with A rather than B rated panes. Be aware that A rated windows are slightly more expensive, however.

Did you just purchase a double glazed window and confused about how to have it installed? Fitting the window yourself can be quite easy with the help of this step by step guide. However, if you lack proper training or experience, we’d recommend you reach out to a trustworthy professional who can guarantee the best results for help. That said, now let’s take a look at the process.

• Remove the old windows by detaching the old beading and glass window safely. Then make some interval cuts using a hand saw before using a crowbar to pry it out.

• Cut the external double glazed window seal. Once done, take a measurement of the window area’s width once empty. Then transfer the measurement to the window sil to face outside and cut using a handsaw.

• Seal the window sil. Add a bead of clear silicone along both inside lip as well as the centre to seal the sil.

• Screw the double glazed window to the sil. Position the window on the top of the lipped section that was siliconed. Then pre-drill them together and screw in three places. You should make sure the screws do not go totally to the sil’s bottom.

• Install the double glazed window. After successfully screwing the double glazed window to the sil, you can now fit in the double glazing. Make use of packers to make sure it’s even in the slot.

• Screw the uPVC window to the wall. If you’re happy and satisfied with the position of the window, you can then pre-drill through the frame of the window and the brick wall. Once done, simply screw it in place using masonry screws or Spax screw as they do not require crawl plugs in bricks.

• Seal around the window. To do this, simply fill any gaps with expanding foam, wipe out the excess and seal with silicone.

Ultimately the double glazing company you use is responsible for the quality of work and to ensure your windows are of an excellent standard. This is why it’s important to get a warranty and use a Fensa registered installer. If problems emerge within a couple of years then it’s likely the installation was of a poor standard.Contact the double glazing company and have the issue repaired or new windows replaced. This doesn’t matter if you received a discount of free windows as part of the deal. As long as you entered into a contract the company is obliged to restore the windows.

Accidents happen, and sometimes windows get broken. And that will lead to you wanting to replace just the glass in your window, rather than the whole frame. Also, as windows get older they can mist up on the inside, which means that the unit has ‘blown’ - so you’ll also need to replace the glass. But how much is it to replace the glass in a window? Luckily, if the frame of your window is in good condition, there’s no need to replace it, and this will reduce the cost. For an installer to fit a new pane of glass in a single glazed window, the average cost is £100, while a replacement double glazed sealed unit will cost an average of £110. Of course, as this is an average, if your window is very large you may spend more, and if your window is very small the price may be less. That's why it’s important to get a range of quotes so you can compare costs and get the best price. If you’re good at DIY, you may feel confident enough to have a go at replacing the glass in your window yourself. In that case, the cost of sealed unit and any other materials you need will cost an average of £57. It’s a significant saving, and if you think you can do it, then give it a try. However, if you’re in any way unsure, it’s best to leave it to the professionals. A window installer will be able to replace the glass in your window in less than an hour. Even though it costs more for a professional to do it, if you get it wrong and have to start over it will cost you more in the long run.

Windows, being a very crucial feature in every home, are one of the things you simply can’t afford to ignore in your home. Having a good understanding and solid knowledge of your windows’ components like the window sash will help you stay up to date with them and able to identify any minor mishaps early on before it leads to a much bigger problem. So what exactly is a window sash?

Well without much fuss, a window sash is simply that part of your windows that’s able to open and close. And there could as well be more than one window sash that’s operable depending on your window’s type. Window sash usually possess a very basic design as well as structure. What’s more? This section of a window happens to be a frame that’s designed in such a way to make for easy placement inside the whole window casement. You’ll discover inside the sash frame, the window glass alongside any framework possessed by your window which includes grids.

Usually, the sash is fitted into the frame of the window on a runners’ set in such a way that allows for both upward and downward movements. And finally, the window sash’s frame typically comes with a locking system which provided for extra safety and security.

The window sash is a vital feature that can determine the durability and overall performance of the windows. In the event whereby your window sash is malfunctioning, it can result to numerous problems which includes both drafts as well as leaks. As a result, it’s very important to keep your window sashes in a great working condition as failure to do so will make opening and closing your windows a really difficult task.