Find a Window Installer you can trust in Woodstock.

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

No matter how big or small a building is, it can only be as good as it’s foundation - and that’s a fact! It all starts from the footing and when it isn’t deep enough, unlike badly installed gutters or gapped hardwood flooring, can make the whole building collapse to the ground. Just like any code recommendations, the depth of the footings of your porch is a parameter that must be complied with and adjusted to suit your local code requirements.

As a rule of thumb, you should always dig below the frost line when excavating your footings. At this depth level, the moisture present in the soil will be frozen. Ultimately, this will help the ground to act as a barrier to insulate the soil below the footing from freezing during the cold months. As a result, in regions where the weather is almost always very cold the depth of your footings is expected to be at least 48 inches. But in areas featuring a warm climate, you may be allowed to install your footings on grade.

In addition, it’s compulsory that your footings must be installed at a minimum depth of 12 inches below unsettled soil. However, if you’re constructing the structure into a steep hill’s side or by the side of a retaining wall, it’s required that you maintain the least distance to grade both vertically and laterally. In the event whereby you need to achieve a good lateral barrier, you’ll need to have your foundation dug a lot deeper compared to if it’s on a flat surface. For a more accurate and updated information, you can consult your local building inspection department to get familiar with the requirements in your area.

Are you about to purchase a double glazed unit and wondering how to go about the replacement project? If yes, then you’re at the right place. Firstly, it’s advisable to hire the services of a reliable professional who can guarantee the best results for help especially if you lack proper training and experience in the field. However, we’ve put together this step by step guide to provide you with a detailed information about the double glazed unit replacement process. Let’s get started!

The tools and materials you require for the project includes tape measure, hammers, nail punch, scraper, spacing blocks, non-hardening butyl putty, high-security glazing tape rolls and beading tacks.

• Work out the glass size required. Simply use the tape measure to measure from frame edge to frame edge while also taking note of the thickness.

• When about to order, inform the glass merchant that the measurement provided are frame-tight. This will make him reduce the dimension a little bit, mostly by 5mm for clearance.

• Remove the beading and ensure to support the glass while doing so. If the glass units are fitted in wooden windows, you may need to cut the putty-based compound they’re normally sealed with to remove the glass.

• Lay out the beading in the window’s shape to make for easier refitting later on.

• If you’re working on wooden frames, wipe out all traces of excess installation compound using a scraper and clean the rebate with a soft brush.

• Trial fit the double glazed windows to ensure they’d slide into the frame without being forced.

• Plastic frame windows are usually in between a pair of gaskets, you should replace this with a hight security glazing tape. While for a wooden frame, simply apply strips of flexible non-setting butyl putty or high-security glazing tape on either sides of the glass.

• Install and centralize the glass in the frame.

• Press the nail wooden beading or plastic beading back into place.

Yes, of course! It’s common for people to replace just one double glazed window. One reason that people want to replace one window is that the sealed unit inside has failed. You’ll know if this has happened because you’ll be able to see condensation on the inside of glass, which gets frustrating because you can’t wipe it away. In this case, you can choose to simply replace the sealed unit or the entire frame, which you might want to do if it’s looking past its best.

When you’re replacing just one double glazed window, if you know the brand of your current windows you could ask your installer if they can source the same ones. This will help to keep them looking as similar as possible, although if your existing windows are very old you may notice some discolouration on the exterior compared to the new one, and locks and trickle vents might look different.

Replacing just one double glazed window shouldn’t take a qualified window fitter long, and could cost as little as £400. If you want to simply replace the sealed unit, that may only cost around £250. You could try to fit a new window yourself, but it’s worth bearing in mind that all replacement windows need to be certified that they’ve been installed to meet building regulations, so you’ll need to apply to your local building control officer who will come and inspect the work then issue a certificate. If you ask an installer who is registered with a self-certification scheme (like FENSA) to fit the window for you, they can issue the certificate themselves when they’ve finished the work.

To install one small double glazed window, it will take anywhere between two hours and half a day. It will depend on whether one installer is fitting your window or two. And if you’re doing it yourself and don’t have any professional experience, it will take even longer.

When the window fitters arrive, they will make sure they’ve got safe access to the window and move any heavy furniture if they need to. Any good installer will lay down a dust sheet, but it’s a good idea to check that they’ve got one laid down before they start.

The first step any window installer will take is to double check the measurements of the new frame against your existing one. Hopefully it should match up, so then they’ll take the old window out. Then, they’ll insert the new frame into the aperture and bolt it into the concrete. They'll check it with a spirit level to ensure it’s even before moving onto the glass sealed unit.

The installer will place the glass into the aperture, then fit the beads to secure the glass in the frame. They’ll then use silicone and trim on the inside and outside to ensure the window looks perfect. You won’t be able to see where they’ve used sealants or trims because they’ll colour match them so it’s not noticeable. Then, they’ll tidy up all of their tools and the working area and let you know what needs to be done in terms of proving that the window meets building regulations. Most good installers are registered with a self-certification scheme, so will be able to issue a certification once the work is complete.

A front porch is a glorious addition that would be a blessing to have in any home. It gives you a good floor space to enjoy your neighbourhood as well as your surroundings in the cool atmosphere of the outside living space. The question however is, how do you build a porch? Constructing the structure can be a very challenging task but with proper guidance and lots of practice, you can also be a skilled porch builder. To protect your investment, it’s advisable to hire the services of a professional for help with your porch especially if you lack proper training and experience. This way, you’ll get to save time and money. This guide is prepared to give you some insight into the porch building process.

lAssess Your Location

• Consider the location before proceeding with the project. It’s essential to select a location that’ll reduce the sunlight coming in.

lPlan The Materials Required For Your Porch

• You’ll have to decide the type of porch you’ll be going for. For example, your porch can be built out of wood, composite decking or if it’s going to utilize some stone flooring, brick or even tile.

lBuild Your Porch Foundation

• Dig the foundations deep to ensure stability while also putting in mind any pipework or cabling

• Fit a damp proof course

• Add the subfloor - this can be concrete or timber

lStart To Lay The Brick And Floor

• Lay the bricks evenly up to the DPC level

• Lay the floor

• Add the flooring protection

• Once done, you can lay the bricks to the window level

• You can fit in a window sill if required before proceeding the brick and block work until it reaches the roof timber’s height

• Fit the linter when you get to the top of where the window will reach.

lConstruct The Roof

• Build a timber framework

• Fit a breathable roof membrane

• Install the roof battens and lay the roof tiles.

• Add gutters

Double glazing is made up of two layers of glass, with a layer of argon gas in between. This type of glass can be used in Aluminium windows. The gas is a poor insulator, helping heat to stay in your home and making your windows more efficient. As well as trapping the argon gas, the second layer of glass reduces the amount of noise that enters your property, and helps to make your windows stronger and more secure.