Find a Window Installer you can trust in Ilminster.

As well as keeping your home warmer and reducing noise, you’ll notice a saving on your energy bills from installing double glazing. If you install A++ rated windows in your home after having single glazing, you could save up to £120 year on your energy bills. The Energy Saving Trust has more information.

Some properties are unable to have double glazing, especially those in conservation areas or listed buildings. To counter this problem and still benefit from a warmer home and cheaper bills, secondary glazing is an option. Secondary glazing is a second pane fitted inside your original window. Secondary glazing will still save you around £105 yearly.

If you’ve got a problem with condensation and don’t have double glazing, you should find that getting new windows will help. Condensation is caused by warm air meeting a cold surface which then turns into water droplets. With two panes of glass, less heat will escape from your home and keep the window warmer, meaning when steam from the bathroom or kitchen touches your windows there should be less condensation.

1. Using a rubber mallet and a strong pallet knife, remove the beading around the window. You might think they’re part of the frame, but they’re actually separate on the inside of the frame and can be taken out by using pallet knife to prize them out. Start with one of the longest beads first and leave the top bead until last.
2. Give the glass a little tap to loosen it if it doesn’t come out straight away, then the whole unit should slide out easily. Just make sure it falls towards you and not back out onto the ground below!
3. Clear any debris that has found its way into the frame with a brush. Add spacers at the bottom of the frame – these could be pieces of plastic.
4. Get your new sealed unit (make sure you measure the glass before you buy one so you know which size to get) and carefully take it out of the packaging. Look for the British Standard mark – that shows you the bottom of the glass.
5. Lift the glass into the frame, starting with the bottom first, and make sure that it fits square in the frame before taking the spacers out.
6. Use a little washing up liquid to spread along the beads to make it easier when you slide them back into the frame. If they simply push and clip back in, you can use something like a block of wood to help you push them in correctly. Put them back in reverse order to how you took them out.

Did you just purchase a double glazed window and confused about how to have it installed? Fitting the window yourself can be quite easy with the help of this step by step guide. However, if you lack proper training or experience, we’d recommend you reach out to a trustworthy professional who can guarantee the best results for help. That said, now let’s take a look at the process.

• Remove the old windows by detaching the old beading and glass window safely. Then make some interval cuts using a hand saw before using a crowbar to pry it out.

• Cut the external double glazed window seal. Once done, take a measurement of the window area’s width once empty. Then transfer the measurement to the window sil to face outside and cut using a handsaw.

• Seal the window sil. Add a bead of clear silicone along both inside lip as well as the centre to seal the sil.

• Screw the double glazed window to the sil. Position the window on the top of the lipped section that was siliconed. Then pre-drill them together and screw in three places. You should make sure the screws do not go totally to the sil’s bottom.

• Install the double glazed window. After successfully screwing the double glazed window to the sil, you can now fit in the double glazing. Make use of packers to make sure it’s even in the slot.

• Screw the uPVC window to the wall. If you’re happy and satisfied with the position of the window, you can then pre-drill through the frame of the window and the brick wall. Once done, simply screw it in place using masonry screws or Spax screw as they do not require crawl plugs in bricks.

• Seal around the window. To do this, simply fill any gaps with expanding foam, wipe out the excess and seal with silicone.

You don’t have to, especially if you’re on a budget. If you’re only replacing some, it’s a good idea to get all the windows on one side of your property replaced at the same time, so they all look the same. Be aware, obviously, huge savings could be had by having a number of windows replaced at the same time.

Whether you need toughened glass in your windows depends on where the windows are in your home or business. Toughened glass is sometimes referred to as tempered or safety glass, and it just means it’s stronger than the standard glass that’s usually offered with double glazed windows. So how do you know if you need it?

Toughened glass is useful in areas of your home where you might come into contact with the windows if you were to trip and fall. If you put your hands out to steady yourself on standard glass the chances are it would break into large sharp pieces with jagged edges. Of course, this means that you could seriously cut yourself if this were to happen. With toughened glass, the structure of the glass is changed so that if it breaks it shatters into lots of tiny pieces, minimising the risk to you if you were to fall on it.

You might want to use toughened glass in patio doors, low windows or frames next to doors. It just means that you will be safer if the unlikely happens and you or a family member falls through the glass. There are certain requirements through Building Regulations with windows at a certain level, but any reputable window installer should be able to go through these with you if you need to replace your windows with toughened glass. The regulations will only apply to new windows – there's no need to switch your windows to toughened glass early, but when you do come to replace them you’ll need to make sure they meet the standard.

A front porch is a glorious addition that would be a blessing to have in any home. It gives you a good floor space to enjoy your neighbourhood as well as your surroundings in the cool atmosphere of the outside living space. The question however is, how do you build a porch? Constructing the structure can be a very challenging task but with proper guidance and lots of practice, you can also be a skilled porch builder. To protect your investment, it’s advisable to hire the services of a professional for help with your porch especially if you lack proper training and experience. This way, you’ll get to save time and money. This guide is prepared to give you some insight into the porch building process.

lAssess Your Location

• Consider the location before proceeding with the project. It’s essential to select a location that’ll reduce the sunlight coming in.

lPlan The Materials Required For Your Porch

• You’ll have to decide the type of porch you’ll be going for. For example, your porch can be built out of wood, composite decking or if it’s going to utilize some stone flooring, brick or even tile.

lBuild Your Porch Foundation

• Dig the foundations deep to ensure stability while also putting in mind any pipework or cabling

• Fit a damp proof course

• Add the subfloor - this can be concrete or timber

lStart To Lay The Brick And Floor

• Lay the bricks evenly up to the DPC level

• Lay the floor

• Add the flooring protection

• Once done, you can lay the bricks to the window level

• You can fit in a window sill if required before proceeding the brick and block work until it reaches the roof timber’s height

• Fit the linter when you get to the top of where the window will reach.

lConstruct The Roof

• Build a timber framework

• Fit a breathable roof membrane

• Install the roof battens and lay the roof tiles.

• Add gutters