Find a Heating Engineer you can trust near you.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

Installing your Nest thermostat may not be as easy as screwing a light bulb, but we can also assure you that it isn’t very difficult either. However, if you lack the needed training or experience to pull it off, we’d recommend you hire the services of a professional in order to save yourself some time and money. This guide will give you some quick and easy steps to follow and ensure you make no errors during the installation process.

Once installed removing the Nest Thermostat can be done. To get started, you’ll need just a Philips head screwdriver which Nest has thoughtfully provided with the device.

• Turn off the Nest Thermostat by switching the circuit breaker to the off position.

• Label or mark your old thermostat’s wires. However, if you notice your thermostat is tagged 120v or 240v, or possesses thick wires, do not connect the wires to the Nest as you have a high voltage system.

• Uninstall the old thermostat by locating detaching the wires coming out from the wall into the thermostat. Once done, simply unscrew the device from the wall

• Mark the spot of your thermostat. Do this by threading wires through the Nest base plate’s centre incorporate the tiny bubble level. Once done, you can then use a pencil to mark te two screw holes.

• Attach the trim plate. If you wish to cover the screw holes, simply install the trim plate in the Nest box’s bottom to the base plate.

• Using the screws and screwdriver, attach the Nest base to the wall.

• Connect the wires to the Nest by putting the labelled wires in the Nest’s corresponding ports.

• Put the Nest display by lining up the connector on the display’s back.

• Turn on the power by switching the circuit breaker to the on position

• Connect your Nest thermostat to the WiFi network.

• Follow the on-screen guide and set the temperature.

• Use your smartphone or tablet to download the Nest thermostat’s mobile app to monitor and control your device remotely.

How Much Is A Gas Safety Certificate?

If you’re a landlord in the UK, then you’d know a gas safety certificate is a legal requirement. If yes, then you’d probably like to know how much it’ll cost to get a gas safety certificate so you can make plans on obtaining one for your property. In this article, you’ll find all you need to know about the amount you’re expected to pay for a gas safety certificate in the UK.

First and foremost, let’s look into the use of the certificate. Basically, a gas safety certificate is the legal inspection of your property’s gas appliances which would be done on an annual basis. Only an approved Gas Safe engineer is allowed to carry out this statutory check. Ultimately, if you own rental properties in the country, this is a requirement you can’t afford to overlook to ensure the safety of your tenants.

Furthermore, included in this inspection are each and every gas appliances, chimneys, pipework as well as flues in the property. In recent times, several individuals make use of fewer gas appliances which ultimately implies that they may only need the servicing of their gas fire. Once you’ve passed the inspection, you’ll be given your CP12 certificate which must be kept for a minimum of two years. A copy should also be provided to your tenants within 28 days of issue. So how much will it cost to get a gas safety certificate?

Depending on your location in the UK as well as the number of gas appliances incorporated, the average cost of a gas certificate will range between £60 to £90. The Gas Safe engineer will carry out the task as a fixed and statutory job.

Breakdowns of boilers are quite common during the winter months and are usually very expensive to repair when this occurs. According to the research carried out recently by uSwitch, repairing a boiler can cost an average of about £314 with a figure over 20 percent of homes experiencing various heating system issues last year.

To answer the question of whether or not your existing home insurance will be enough to cover the boiler breakdown, the answer is probably not. This is due to the fact that heating system faults or breakdowns is a very common occurrence and as a result of poor maintenance practices as well as a high repair cost, several insurance companies often remove it from their home insurance policies.

Generally, you’d be given an option of what is termed as “emergency home cover which is an add on or extra to your home insurance policy. Luckily, this add on is quite inexpensive and may be as little as £4 or £5 per month. Depending on your need or budget, you can also purchase the add on as a “stand alone from your current insurer or another company. However, the standalone option is usually more expensive.

The emergency home cover normally provides coverage for the boiler repair cost and few times, the rest of the central heating system as well. Being fully aware how important a boiler can be, insurance companies usually deliver a rapid response service as suggested in the name, “emergency home cover. However, the maximum pay-out for call out charges is capped at a particular amount which usually ranges from £500 and £1,000. Apart from the call out fees, the emergency cover also includes a limit on the pay-out amount for future required repairs of heating systems which includes both parts labour.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

1. Switch off your boiler and let it cool completely
2. Make sure both ends of your filling loop are attached
3. Open both valves to allow cold water into the system – you’ll hear it start to move
4. Look out for your pressure gauge to show 1.5 bar
5. Close both valves
6. Switch your boiler back on
7. Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

Are you worried about blocked drains? Yes, you probably should! As a homeowner ( with a detached, semi detached or terraced house), all plumbing and drainage issues within your home or even within your property boundary is your responsibility. Hence, you’d might want to consider getting a Homeserve plumbing and drainage cover to help keep your home running smoothly and putting your mind at ease. The only exception here is if the drain in question is a lateral drain which is a common feature in flats. In this situation, it’s only the building managers that would be responsible for the maintenance of the drainage as it’s shared between several homes. Before 2011, the various flats or houses that shares the lateral drain are responsible for its maintenance.

Working with top utility companies for over 2 decades, Homeserve has positioned itself as one of the leading home assistance providers in the United Kingdom. With their top notch services, they’ve been able to make their client’s lives a lot easier and stress free through the provision of a wide array of repair solutions such as drainage, plumbing, heating, electrics and a lot more.

As a homeowner with the responsibility of maintaining the drains and ensuring there’s no block or damage, it’s simply a no brainer to go for a plumbing and drainage cover and more importantly, get good cover. Homeserve are one of the providers but there are a number of others which offer great service at competitive prices. Without an insurance in place, you may just have to break the bank just to have an engineer or plumber to fix any plumbing or drainage issue you might have. So why not give yourself a peace of mind and get a cover today?

How To Make Oil Boiler More Efficient?

During the winter months when the nights get darker and colder, it’s more likely your oil gets used up a lot more quickly. This can be very worrisome as it implies having to spend more money to refill. So what exactly can be done to make your oil boiler more efficient and save you some money?

• Regular Servicing Of Your Oil Boiler

Getting your boiler serviced by a manufacturer approved engineer on an annual basis is one of the easiest and quickest ways to ensure that your oil boiler is operating at its maximum efficiency level. When a full servicing is provided for your oil boiler, checks are made to ensure that all components are functioning the way they should while also identifying the bad or worn parts that may be hindering your oil boiler from functioning in an effective manner. As a result, it helps you see to the fact that your boiler is not consuming more than necessary to make sure your oil boiler lasts longer.

• Set Your Thermostats Correctly

When you set your room thermostats and thermostatic radiator valves (TRVs) the right way, you’ll be sure to get a comfortable home without having to make use of much fuel.

• Consider Smart Technology

If you decide to make use of smart technology like Nest or Hive, you can save more money when compared to their more conventional counterparts. These smart technologies incorporate highly advance intelligent systems to get more familiar with your lifestyle, habits as well as heating operations in order to ensure optimum efficiency at all times.

• Put Your Radiators To Good Use

Try as much as possible to avoid some oversights that can make your radiators consume more energy than required. Consequently, you have to keep them clean, give them space and also take care with curtains.