External wall insulation in Atherstone

If you want to install an external wall, it is only wise to consider whether or not a planning permission is required in order to avoid a hefty fine. In a great kudos to the government and a welcome relief to home and property owners, the installation of external wall insulation is seen as an “improvement to the house and not an “extension or an “enlargement. Ultimately, this implies that external wall insulation fitting is to be done under permitted development and a planning application may not be required. However, like many other regulations, there are also exceptions to this rule and the main one is if the activity changes the appearance of your property. Properties such as a listed building having tighter regulations may pose some issues. As a result, we’d advise you to consult your local authority to ensure that there’s no fast rule to this topic before commencement of the external wall insulation project.

At the moment, according to the Government Building Regulations, the surface of the entire wall is to be improved to existing standards if the area to be insulated exceeds 25 percent of the wall. In normal situations this is usually the typical case, however to prevent avoidable fines and other possible punishments, it is always best to reach to your local authority and check out the rules guiding external wall insulation in your constituency. Furthermore, since external wall insulation is not a task that’s recommended to be done by yourself, you can also ask the professional external wall insulation fitting company for the applying rules before proceeding. As a good professional, the company should have a better knowledge of the rules and regulation guiding its activities.

The answer is yes! Houses whose external walls have been insulated are more valuable than their uninsulated counterparts. And not only does it add to the value of a home, but also significantly reduces the amount of electricity consumption. This is a major turn on for potential investors which implies a greater demand and ultimately, a higher price. The real estate market is a very dynamic one which can be hard to predict at any particular time. The frequent changes in price are usually down to factors beyond the owners’ control, but if you’re looking to put up your house for sale in the near future, it would be a wise decision to consider ways in which you can increase its value. While renovating each room can be on the expensive side, a great solution would be insulate the external walls.

An insulated house is one that is well secured against the harmful impact of extremely high or low temperature, humidity and other atmospheric factors. Hence, the reason why a house with external wall insulation has a greater value which you would not want to miss out on. What’s more? You’ll get a great thermal insulation with the top notch materials like foamed polystyrene, high quality renders, mineral wool or polyurethane.

With an external wall insulation, you know the transaction will always be favourable on both ends. You get to smile to the bank, while the buyer also gets to enjoy great value for every penny spent. To employ the services of a reliable external wall insulation expert, simply conduct an in depth research from family and friends, online and other sources. Go through their online reviews and ask questions to become more familiar with the process and its value-adding potentials.

With the numerous benefits that comes with the installation of an external wall insulation in a building, it’s also important to find out whether it’s also safe before proceeding to fit one in your home. Firstly, to ensure that external wall insulation systems are safe, they must be BBA approved, which means they’ve been subjected to a thorough testing by the British Board of Agrement and therefore, suitable for use in UK homes.

Given the fact that cladding materials have recently generated a lot of debate and negative press about how reliable some particular materials are, questions are being asked of the safety and reliability of external wall insulation. However we must clarify that, although external wall insulation can be classified under cladding, it is very different to rainscreen cladding - which caused the Grenfell fire tragedy.

External wall insulation is completely safe. However, when it comes to fire, the safety of your system depends largely on the insulation type in question. The safest type of insulation you can have installed is the Rockwool insulation boards which are rated as Euroclass A1 non-combustible. The board is specially designed in such a way that it contains fire - preventing it from reaching the other areas of the building. They also do not produce harmful emission or smoke when impacted by fire.

Meanwhile, the Wood Fibre, is also a great insulation which is known to char and not burn. Contrary to many beliefs, it actually burns slowly creating this charring effect which produces an oxygen barrier that helps reduce the spread of fire.

To make your system safer, you can also make use of Fibreglass Mesh for reinforcement. It helps to improve the strength of the tensile which promotes the security of the boards attached to the wall.

With the title of this blog, do not be deceived into thinking the purpose is to encourage you to install an external insulation by yourself. Even as a competent DIYer, it’s not advisable to buy a couple of materials and start slapping it into the wall hoping for the best outcome. External insulation is by no means a DIY job and without the proper training and experience, it can easily turn out disastrous resulting in loss of time, effort and money in such a valuable project. This blog, however, will give you a great insight on how the installation process works and help maximize knowledge ensuring you do not spend more than necessary.

External Insulation Installation

lRender Test

• This is done to ensure the existing render is good enough for insulation support.

• If positive, the insulation can be applied directly onto it.

• If negative, ensure removal of the old render before fitting the insulation.

lPipework Adjustment & Removal

• Remove all pipework prior to insulation fitting

• Install temporary downpipes to ensure water is not wasted and everything continue to function normally during the insulation fitting process.

lWindow Protection

• Protect the window with a protective layer or film.

lStarter Track Fitting

• Determine level you want the insulation to start (height).

• Fit the aluminium start track or carrier tray at the identified level.

lInsulation Boards Fitting

• Apply a layer of adhesive to the board and glue them to the wall in a staggered pattern.

• Cut to fit round all obstructions and windows.

• File off the edge of the board where necessary using a rasp upon successful fitting of the boards

lMechanical Fixing Inclusion

• Hammer around 10 fixings per square metre into the board.

• This is to secure the insulation boards.

lBeading Fitting

• Add corner beads and stop beads to ensure the insulation is secure and to prevent it from making contact with other materials.

lReinforcing Mesh & Render Addition

• Apply two layers of strengthening properties and between the two layers of render, include a fibre glass mesh.

lPrimer Application

• Paint on the primer

lFinal Render Application

• Choose your most preferred texture and colour as this will be the last coating of the installation process.

lPipework Re-installation

• Re-install all detached pipework at the start of the installation process.