Painting / Decorating in County Fermanagh

How To Prep Walls For Painting

This is exactly the part of a wall painting job that can make or mar the whole project. To ensure that your paint project doesn’t end up being disastrous, the most important place to start is from room preparation which includes cleaning, sanding as well as priming the walls before painting. Not every wall will require to go through all the preparation steps as all walls are unique and some are in better conditions than others. However, it’s advisable to thoroughly inspect the surfaces before you proceed to painting and take the necessary actions where required.

This is a very simple DIY job that should be completed in little time, however it’s also perhaps the most important step of the entire painting project. Hence, if you lack the confidence to pull this off, then we’d recommend employing a painting expert who can guarantee the best results for help. In this guide, we’ll should you how you can prepare your wall for painting.

✓ Cleaning. There is no single best way to properly clean a wall, but most walls will be just fine with a sponge and warm water. For walls that have been stained with oil or grime such as kitchen walls, you can apply grease cutting detergent and water mixture to wash and follow up with warm water to clean the residues and a damp cloth wiping to finish it off. Then leave to dry off properly.

✓ Remove mildrew. Wipe out mildrew using a sponge and solution that’s three to four parts water to one part bleach. Apply this solution and scrub the affected surface with a soft brush.

✓ Sanding. This step is only meant for walls with rough spots on its surface. Dull the uneven spots with a sandpaper, wipe away the dust and leave to dry. Use a fine grit sandpaper to sand the surfaces and let it dry properly.

✓ Priming. Prime the wall to get the most out of your paint. They work to disguise imperfections and create a smooth surface on which you can work on.

Yes, painters and decorators can repair stained, damp or mouldy walls. Usually, this process will involve stripping away the damaged paint and treating the area with specialist paint. After this is done, the damaged sections can be repainted to match the room.

How To Paint A Ceiling

If you’re a bit hesitant to take on the seemingly awkward task of painting your ceiling, you’re definitely not alone. However, there are ways in which you can make ceiling painting tasks one of the less strenuous tasks you’ll find around the house as they’ll help you get rid of most drips and also assist you to easily determine whether or not you’re covering the whole ceiling. In several cases, painting a ceiling simply means painting it white again and most same colour painting jobs are way easier than painting with a new colour entirely. When you have the right size of nap controller as well as the appropriate length of an extension pole, painting over your head will be a lot easier. Here’s how to paint a ceiling.

✓ Prepare the room. This include removing as many furniture and objects from the room as possible while also laying down plastic sheets on the remaining ones. And also cover the floor with paper or canvas drop cloths.

✓ Remove obstructions. Detach or remove everything that can make your work harder like light fixtures or smoke detectors.

✓ Protect surfaces. This includes protecting vertical surfaces like the windows and doors from ceiling paint.

✓ Prepare the ceiling. This involves vacuuming the ceiling to get rid of any dust or dirt, sanding any rough spots on the ceiling with a sandpaper and filling any small holes or cracks in the ceiling (optional).

✓ Prime the ceiling. Use an angled brush or paint edging tool or primer to cut in edges of the ceiling.

✓ Paint the edges of the ceiling. When the primer has dried, simply paint the edges of the ceiling to create a frame in which you can easily work in.

✓ Paint the ceiling in grids.

How To Paint A Room

Painting is a joyful task and it’s quite obvious why it’s one of the most popular DIY projects. Whether you’re painting as an experienced DIYer or as a newbie, this step by step guide will put you in the right direction. However, if you lack the confidence to carry out this task, then we’d recommend you get in touch with a seasoned professional who can guarantee the best results for help. This way, you get to save some time and additional money that would have resulted from possible costly errors.

So just before you head right into the task, there’s the need to determine the type of pain finish you would love to use which is to choose a colour. Now let’s get started!

• Prepare the room

✓ Remove all objects as much as you can from the room and cover the remaining furniture or objects with a sheet.

✓ Fill all holes on the surface to make for an even finish.

✓ Wash the wall with the help of a damp sponge. A sugar soap or diluted washing up liquid will work just fine.

✓ Tape the edges of objects you do not wish to paint like light switches, plug sockets and the likes.

• This step can be skipped if painting on an existing paint, but it’ll advisable to dilute small quantity of your selected paint to patch prime the holes that you’ve filled. If you have a large number of holes that was filled, then priming them would be smart.

• Mix or stir the paint thoroughly in a paint kettle to ensure an even and perfect mix.

• Now you’re ready to start painting! Start from the edges to form like a frame to work within with your roller. Once done, leave for about 4 to 6 hours to dry.

• For the second coat, simply repeat the above step to complete your painting project.