Painting / Decorating in Strome Ferry

How To Prep Walls For Painting

This is exactly the part of a wall painting job that can make or mar the whole project. To ensure that your paint project doesn’t end up being disastrous, the most important place to start is from room preparation which includes cleaning, sanding as well as priming the walls before painting. Not every wall will require to go through all the preparation steps as all walls are unique and some are in better conditions than others. However, it’s advisable to thoroughly inspect the surfaces before you proceed to painting and take the necessary actions where required.

This is a very simple DIY job that should be completed in little time, however it’s also perhaps the most important step of the entire painting project. Hence, if you lack the confidence to pull this off, then we’d recommend employing a painting expert who can guarantee the best results for help. In this guide, we’ll should you how you can prepare your wall for painting.

✓ Cleaning. There is no single best way to properly clean a wall, but most walls will be just fine with a sponge and warm water. For walls that have been stained with oil or grime such as kitchen walls, you can apply grease cutting detergent and water mixture to wash and follow up with warm water to clean the residues and a damp cloth wiping to finish it off. Then leave to dry off properly.

✓ Remove mildrew. Wipe out mildrew using a sponge and solution that’s three to four parts water to one part bleach. Apply this solution and scrub the affected surface with a soft brush.

✓ Sanding. This step is only meant for walls with rough spots on its surface. Dull the uneven spots with a sandpaper, wipe away the dust and leave to dry. Use a fine grit sandpaper to sand the surfaces and let it dry properly.

✓ Priming. Prime the wall to get the most out of your paint. They work to disguise imperfections and create a smooth surface on which you can work on.

Can You Paint Over A Wallpaper?

According to some painting and decoration experts, painting over a wallpaper can never produce a result that’ll be as good as painting on a blank or naked wall. However in the event whereby there’s a pressing need to quickly beautify a room, it’ll be totally understandable if you don’t want to go through the hassle of the time consuming old wallpaper removal process.

Therefore, the short and simple answer to this question is yes, it’s absolutely possible to paint over a wallpaper and get a good outcome so far you don’t rush the process. To ensure your success if you want to paint over a wallpaper, there’s also the need to use the right tools and techniques. And just like any other DIY project, proper preparation before commencement is key.

If you’re going to paint over a wallpaper, many of the tools you’ll need to acquire are the standard painting and decorating products. This means that they can be easily procured at many DIY stores. To paint over a wallpaper, you’ll need a paint roller, top quality paint brushes, joint compound ( you’ll only need this in situations whereby your wallpaper is damaged or peeling), oil based primer, tape, sandpaper, paint ( can be water, solvent or oil based paints) as well as drop clothes ( for the protection of your furnitures).

As a rule of thumb, if you can easily remove the existing wallpaper, then you probably should before you start to paint the walls. However, if removing the wallpaper seems to be a pain or can significantly damage your wall, then it’ll be smart to simply paint over it. But before you proceed, you must also note that painting over the wallpaper will make it even harder to remove later in the future.

You should always wait until plaster is dry before painting. The time this will take varies depending on the room and property, but in general, it will take about a week. Your plasterer will tell you how long it is best to leave it before covering or painting their work.

How To Paint A Room

Painting is a joyful task and it’s quite obvious why it’s one of the most popular DIY projects. Whether you’re painting as an experienced DIYer or as a newbie, this step by step guide will put you in the right direction. However, if you lack the confidence to carry out this task, then we’d recommend you get in touch with a seasoned professional who can guarantee the best results for help. This way, you get to save some time and additional money that would have resulted from possible costly errors.

So just before you head right into the task, there’s the need to determine the type of pain finish you would love to use which is to choose a colour. Now let’s get started!

• Prepare the room

✓ Remove all objects as much as you can from the room and cover the remaining furniture or objects with a sheet.

✓ Fill all holes on the surface to make for an even finish.

✓ Wash the wall with the help of a damp sponge. A sugar soap or diluted washing up liquid will work just fine.

✓ Tape the edges of objects you do not wish to paint like light switches, plug sockets and the likes.

• This step can be skipped if painting on an existing paint, but it’ll advisable to dilute small quantity of your selected paint to patch prime the holes that you’ve filled. If you have a large number of holes that was filled, then priming them would be smart.

• Mix or stir the paint thoroughly in a paint kettle to ensure an even and perfect mix.

• Now you’re ready to start painting! Start from the edges to form like a frame to work within with your roller. Once done, leave for about 4 to 6 hours to dry.

• For the second coat, simply repeat the above step to complete your painting project.