Painting / Decorating in Tavistock

How To Prep Walls For Painting

This is exactly the part of a wall painting job that can make or mar the whole project. To ensure that your paint project doesn’t end up being disastrous, the most important place to start is from room preparation which includes cleaning, sanding as well as priming the walls before painting. Not every wall will require to go through all the preparation steps as all walls are unique and some are in better conditions than others. However, it’s advisable to thoroughly inspect the surfaces before you proceed to painting and take the necessary actions where required.

This is a very simple DIY job that should be completed in little time, however it’s also perhaps the most important step of the entire painting project. Hence, if you lack the confidence to pull this off, then we’d recommend employing a painting expert who can guarantee the best results for help. In this guide, we’ll should you how you can prepare your wall for painting.

✓ Cleaning. There is no single best way to properly clean a wall, but most walls will be just fine with a sponge and warm water. For walls that have been stained with oil or grime such as kitchen walls, you can apply grease cutting detergent and water mixture to wash and follow up with warm water to clean the residues and a damp cloth wiping to finish it off. Then leave to dry off properly.

✓ Remove mildrew. Wipe out mildrew using a sponge and solution that’s three to four parts water to one part bleach. Apply this solution and scrub the affected surface with a soft brush.

✓ Sanding. This step is only meant for walls with rough spots on its surface. Dull the uneven spots with a sandpaper, wipe away the dust and leave to dry. Use a fine grit sandpaper to sand the surfaces and let it dry properly.

✓ Priming. Prime the wall to get the most out of your paint. They work to disguise imperfections and create a smooth surface on which you can work on.

How To Paint Skirting Boards

In the exact same way a room isn’t complete unless it has all the right finishing touches here and there, your skirting boards also just wouldn’t be right leaving it without a paint. As you can imagine, skirting board can quickly gather dust, dirt and scuffed over time can affect the appearance of the entire room. But you don’t have to wait for this to happen before painting your skirting boards. Good news is, painting of skirting boards is relatively easy and straightforward especially when you follow the guide given in this article. It should, however, be said that if you’re not so confident about holding a brush and doing the task yourself, then getting a professional painter to complete the project will be a great option to achieve the best result while you can focus on other important things.

Painting your skirting board will help provide your room with the much needed perfect frame. Now let’s take a closer look!

✓ Prepare your skirting boards. Treat your wood skirting board with a knotting solution and wood primer. But if they’re already painted or varnished, simply wipe clean use a wet and dry paper with a mild detergent to abrade the surface. Once done, you can then run a strip of masking tape along the floor.

✓ Start Painting. For the decorative coat, you can use any paint designed for wood and metal like satin, gloss etc. Once selected, you can then start to paint across the top with the help of a 2 inch brush. Then move to the flat side. Work in easy to manage sections and when starting the next section, start at the far side and brush into the section you’ve just painted so as to make for an even finish. Finally, remove the masking tape used before the paint dries off.

How To Paint A Radiator

First thing you should know about painting a radiator is that normal paints can’t be used to do the job, however that doesn’t mean it’s not cheap, easy and fun - it definitely is and even more so, when you do it the right way. With a few radiator painting hints here, it’s only a matter of time before you start painting your radiators every colour of the rainbow delightfully.

Painting a radiator is not one of the most common tasks on most people’s to do list, so we’ve created this article as an encouraging nudge to allow more people let their creativity manifest through a brush. However, this is not to say that this is a task for everyone though as you won’t like to make a mess of your radiator. If you know you can’t pick up a brush or bend a knee or your back here and there, then you probably shouldn’t. In such cases, hiring a professional painter would be your best bet to get the best results while also saving yourself some time and money.

To paint a radiator, you’ll need a paint brush, suitable radiator paint, dust sheet and a radiator paint brush (optional).

✓ Turn off the radiator and leave it to cool off. Once it’s cold, simply wipe out all dust, dirt or grease from the radiator.

✓ Protect the flooring under the radiator from any paint splatter with a by spreading out a dust cloth.

✓ Use a suitable radiator paint to brush out well and lay off evenly in a direction. Leave it to dry overnight. Then apply paint on the radiator in direction of the grooves with the help of a top quality brush.

✓ Paint in sections and move across the radiator slightly overlapping until you get to the end. The move to paint the other areas.

✓ Leave the paint to dry as instructed in the manufacturer’s instructions, then apply a second coat if necessary.

You should always wait until plaster is dry before painting. The time this will take varies depending on the room and property, but in general, it will take about a week. Your plasterer will tell you how long it is best to leave it before covering or painting their work.