New Flat Roof in Herefordshire

How To Replace Flat Roof Felt

Also referred to as tar paper, roofing felt is installed underneath the roof’s shingles to help deny water access to your home. Installing the roofing felt in overlapping layers builds a water barrier in situations whereby the weather damages or blows away the shingles. Although the application of a roofing felt on a flat roof is relatively easier and safer than working on a peaked roof, it’s advisable to take enough care and precautions. If you lack proper training and experience for this task, we’d recommend you employ a reliable professional to guarantee the best results and save you from further headaches especially in cases whereby unfortunate errors are made. This step by step guide will give you a good insight into the flat roof felt replacement process.

• Take a measurement of the width and length of the roof.

• Calculate the square footage by multiplying the numbers.

• Multiply the square footage gotten by three (it’s advisable to install three layers of roofing felt to create a really strong weather barrier).

• Use a claw hammer to remove the existing roofing felt.

• Use utility knife to cut the new felt to fit the length of the roof.

• Place the first piece along the roof’s edge and use a hammer tacker to tack the felt in place with staples or galvanized nails and hammer.

• Put the staples or nails at every 6 inches along the side touching the roof’s edge as well as down the short sides.

• Repeat the same process for the second piece, laying it out beside the first row of felt.

• Cut a piece of felt to the appropriate length using a utility knife to begin the second layer of roofing felt, and cutting it in half, lengthwise.

• Apply construction adhesive along the first row using a trowel.

• Press the first piece for the second layer onto the adhesive. Repeat this process until the roof is covered with a second layer

• Apply construction adhesive over the second layer to install the third layer. Begin with a full piece of felt without cutting it in half.

• Overlap each piece by 2 inches until you’ve completely installed the third layer.

How To Replace Flat Roof Fascia

Whatever makes you decide to install your flat roof fascia by yourself and not a professional company, then you must have a clear idea of what to do and do it appropriately. If you lack proper training and experience, we’d recommend you employ a reliable professional to help with the task for the best results and save you some time and money. This step-by-step guide will give a clear insight on how to go about the replacement of your flat roof fascia.

The tools to be incorporated includes the fascia boards, table saw, plane, crimper, clamps, power nailer, compound saw and chalkline.

• Prepare and get all the necessary tools to complete the task before commencing as this would save you time from stopping and going back and forth looking for the next tool needed,

• Install the sheathing and board.

• Fix white fascias with at least 600mm centres ( a foiled fascia needs just 40mm centre) using a marine grade stainless steel plastic headed nails.

• Make a space of up to 10mm between the joints for possible building expansion, using super glue to secure the joints to just a side of the fascia.

• Place this directly on the fascia board’s top (if you’ll be installing ventilation) to create an air pathway.

• Take note that the type of roof to be installed will determine how you’ll have to install the fascia board. For instance, a hip roof permits you to attach the fascia board onto the roof in a quick fashion, whereas a gabled roof may need you to make markings on the board to achieve the right fit.

• Consider the depth of the fascia board as it also play a huge role in the installation of the fascia board. For instance, there’ll be additional weights on tiled roofs that will push up against the board. Therefore, if you do not get the appropriate amount of depth, it could eventually collapse.

If your existing roof is still in good condition but the membrane is getting old, it’s often not worth exposing the structure to the weather whilst the contractor strips off the old membranes. The contractor will leave them in place to act as a base layer for a new roofing system. As long as there are no other problems with your roof, then overlaying is a good way to replace your flat roof.If you have any more questions about flat roofing that aren’t listed here, fill out our form to ask a contractor.

What Is The Average Cost To Replace A Flat Roof?

Are you interested in knowing how much it costs to replace a flat roof? Here, you’ll discover a price breakdown for replacing flat roof. This includes a number of price determining factors such as materials costs as well as cost of labour and cost per square metre. All these enables you to make easy calculations so that you can determine a flat roof replacement estimate for your own project.

The type of flat roof that is the most common type is the garage roof and for the replacement of a single garage roof, the cost will fall between the range of £700 to £1000. Meanwhile for a double garage, you should expect a price increase of about 40 percent to 50 percent. The main price determinant that’s affecting the price of a new flat roof is the material incorporated in making it. For instance, lead or fibreglass are much more expensive when compared to felt roofs.

Generally, the cost of a flat roof replacement will fall within the range of £700 to £1300 varying largely due to the type of materials to be used by the roofer, the roof’s size as well as whether or not scaffolding would be used. Multiple flat roof applications also comes with different costs which includes:

• Felt roof ( £40 to £60 per square metre).

• Fibreglass roof ( £70to £90 per square metre ).

• Rubber roof ( £80 to £85 per square metre ).

• Lead bay roof ( £90 to £105 per square metre ).

• Fibreglass bay roof ( £40 to £60 per square metre ).

Several professional roofers work in pairs and to hire them you’re likely to be charged between £200 to £300 per day. The project can be completed with just a day’s work, but the installer should be back to make sure there are no leaks.