Find a Builder you can trust in Abbots Ripton.

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

How To Fit Plasterboard

If you’re planning to renovate your house, then here is a must-read guide! Fitting of plasterboard is a crucial step when it comes to renovation. If you’re bringing down an existing lath and plaster for an upgraded surface or adding a new wall, a plasterboard is required for your project to be a true success. If you’re a novice with no prior practice or experience, you can protect your investment by hiring the services of a professional plasterer to guarantee the best results, the first time. However, we’ve put together this guide to give you an insight on how the plasterboard fitting process is done.

To get started, you’ll need a power drill, hammer, plasterboard nails or screws, broad knife, utility knife, measurement tape, pencil, ladder as well as a joint tape.

Before proceeding, you need to identify the number of plasterboard sheets needed to commence the project by measuring the height and width of the wall as well as calculating the square footage. If you possess a stud timber wall, the steps below will get you the best results.

• Measure the walls and mark the plasterboard where you’ll make the cuts. Start with a full sheet and cut pieces down in such a way that would fit

• Score the front paper of the plasterboard with utility knife. Fold the sheet to get a clean cut through the board and make use of the knife to the remaining paper.

• Place the first sheet against the wall and use an offcut to prevent the plasterboard from touch the floor.

• Make the plasterboard rest snugly against the wall in position and screw it firmly on each stud. Once done, fasten it at all the sheets’ edges and in a line down the stud to make for a firm connection. Follow the same process for the remaining plasterboard sheet till the wall is fully covered.

Driveway surfacing materials like concrete, asphalt and clay brick usually crack because they’ve been exposed to extreme temperatures or put under high pressure. It’s important to repair driveway cracks before they get worse and cause damage to vehicles and perhaps others to trip on raised cracks.

Cutting a plasterboard is a relatively simple process requiring only some basic tools. Unfortunately, the lack of knowledge serves as big deterrent for many people who wishes to put it to good use. Plasterboard can actually be sawn using an ordinary timber saw that’s fine-toothed to get a cleaner edge. However, the basic tools you may also need includes a sharp knife (Stanley Knife), pencil, a fine sandpaper, a straight edge and measurement tape as well as a wall board saw. Let’s have a look at the cutting process!

• Firstly, you need to put the plasterboard sheet flat on a firm surface.

• Use the tape measurement to measure the cut you wish to make.

• With the help of a pencil, simply mark out the part you wish to cut on the plasterboard’s front side.

• Once marked, place a spirited level over the marked spot on the plasterboard sheet you want to cut.

• Cut a shallow mark into the plasterboard sheet using the Stanley Knife to cut along the edge.

• The cut should be slow and gradual to ensure you do not wander off the edge of the marked area.

• Once the shallow cut has been made, turn the plasterboard sheet on its edge and deliver a quick and sharp push towards the plasterboard’s back and on one side of the cut.

• Place the plasterboard sheet backing against a flat surface ensuring the line of the cut is over an edge. Once done, give a quick and sharp push towards the back of the plasterboard sheet and on the part of the board is reaches beyond the edge.

• Using a fine sandpaper, remove all forms of paper burrs.

The process of cutting plasterboard requires a lot of practice. If you lack the training and experience, the cutting process is best left to a proficient professional who can guarantee the best results the first time and save you some additional costs due to potential damages.

Yes. Most extensions will add substantial value to your home, and you may find that the extension adds more value than it cost. However, it’s important to be sure that the home remains balanced. Extending your garage and leaving your property with no parking spaces, for example, may impact your ability to sell.

Most companies will make the building control application on your behalf and ensure that all the work is completed to the right standards. When a building inspector has inspected it, you’ll get a certificate. It usually takes around 6-8 weeks after completion to come.

Do I Need Planning Permission For A Loft Room?

The answer to this question is maybe. Generally, loft rooms are covered under “Permitted Development which means you won’t need to apply for a planning permission to build a loft room. This is like an advance planning permission provided by local authorities to allow some particular building works to be done such as loft conversions, rear extensions and more. When you’re covered by a “Permitted Development, you’re given the free range to oversee your home’s development without much interference from the regulations or the council. However, for permitted development to apply, there are some specific criteria that must be met. Therefore, if your loft room does not meet the following requirements given below, then you must complete a planning application before proceeding.

• In a terraced house, the converted loft space must not be more than 40 cubic metres.

• In a detached building or semi detached house, the converted loft space must not be more than 50 cubic metres.

• The existing roof slope at the front of the house must cover the extension made.

• The extension should not increase the height of the roof in any way.

• Verandas, balconies and any other structures of this nature must not be included in the extension’s plan.

• The side facing window openings should be at a minimum of 1.7 metres above the ground. The windows must be obscured as well.

• The roof extension should be set back as far as practically possible. It should be at a minimum of 20cm from the current eaves.

• The roof extension should not overhang the house’s roof or it’s wall.

• The materials to be incorporated must be the same or at least similar to what you already have on the house’s exterior.

The holy grail of home extensions is basically the need for additional space for living as well as leisure. However, before commencing your home extension project, you’d probably want to know just how big your new building can be. In this article, you’ll find the answer to this question which is also frequently asked by many other home or property owners in the UK.

Besides your budget, there are two other major influencing factors that can determine just how much extra room that can be added. These factors include whether you wish to carry out the extension project under Permitted Development rights which is usually for a smaller project or you’d prefer to opt for a larger project which is covered by Planning Permission.

Apart from the limitations in the size of an extension under Permitted Development, the extensions are also a lot more affordable and consumes less time when compared to the extensions under planning permission. So what exactly is the size limit for an extension under Permitted Development and the ones under Planning Permission?

For a single storey extension, the maximum size that can be constructed without having to submit an application for Planning Permission includes:

• An extension should have a maximum length of 6m, if you reside in a terraced home or a semi-detached property.

• Extensions for detached properties can have a maximum length of 8m.

• The extension built must not go beyond half your garden’s area.

• The extension should have a maximum height of 4 metres, but in the event whereby the extension is situated within 2 metres of the boundary of your property, it should not exceed a height of 3 metres.

• The extension should not be higher than the highest part of the existing house’s roof.