Find a Builder you can trust in Buntingford.

Most companies will make the building control application on your behalf and ensure that all the work is completed to the right standards. When a building inspector has inspected it, you’ll get a certificate. It usually takes around 6-8 weeks after completion to come.

Driveways usually sink because they haven’t been laid properly. They may not have been dug deep enough, or the installer might not have used the right materials. This will need to be corrected at the earliest opportunity, although in extreme cases, the driveway may need to be completly be relaid.

Pebble dash is an effective way to tune up your house or property as it can go a long way to enhance its curb appeal while also add to its resale value if you should decide to sell later on. Although, it’s highly recommended to leave this task for a reputable specialist, it’s also something that can be done as a DIY task. It must be states that this is a pretty difficult job and even more so if you haven’t attempted it before. In this post we’re going to take you through the processes involved in pebble dashing a wall. Let’s take a look!

• Mix up water with the lime strictly following the manufacturer’s instructions. Once done, leave it covered up to hydrate for at least 24 hours.
• Take one part of the slaked lime and mix it up with cement and six parts sand. This is to give the base mixture required to spread onto the surface.
• Use a trowel to apply the mixture onto the wall. Ensure that the trowel is level and use the edges to make a flat and smooth layer of the mixture on the surface as a base layer. Allow the base layer to dry for up to an hour. Then, rake the surface using a notched trowel and allow to dry for a minimum of 24 hours.
• Rinse and drain your pebbles. Then, set them under the wall you’re pebble dashing.
• Take the top coat of five parts sand and mix with one part cement and one part slaked lime. Use a trowel to apply this mixture over the base layer and smoothen it with the trowel to create a flat and even top layer.
• Spread a plastic sheet beneath the wall you’re pebble dashing to capture any loose pebbles as they fall.
• Grab the bucket of pebbles below the wall and scoop some of the pebbles up using a scoop or trowel. Some will stick and some will fall into the plastic sheet already placed below. Continue throwing the pebble dash until the surface is completely and evenly covered with pebbles.
• Lightly press and fit the pebbles on each section into the wall and leave for at least 24 hours to dry.

Cavity wall insulation is basically the process of installing an insulating material between the two layers of brick making up a cavity wall, either as a retrofit measure or at the time of building. Obviously this is not a choice if you have solid wall, but for those who do possess a cavity wall, it represents an opportunity you may not want to let slide as it is a worthwhile and affordable wall insulation option. Clearly, cavity wall insulation will make your home or property feel warmer, but it also does come with a range of other benefits which is why we’d recommend installing it. In this post, we’re going to look at a number of reasons why having a cavity wall insulation done is a good idea.

• It’s one of the cheapest energy saving measures that’s available. Not only is cavity wall insulation really effective, but it can also deliver great saving. In other words, it possesses a bigger payback compared to other options. When compared to other types of insulation, you can’t install cavity walls insulation by yourself, however it’s not so expensive to have it installed. The cost of the insulation will be determined by a number of factors such as your location, the company hired and more.
• It reduces your energy bills. Cavity wall insulation can save you about £100 to £200 on a yearly basis on heating bills. In other words, this is usually able to pay for itself in as little as two years.
• It reduces your carbon carbon footprint. If your home is heated with gas or electricity like several other homes, producing that energy involves burning fossil fuels which is known to be hazardous for the environment. If the heat generated is now allowed to escape through the walls, that means you’d have to use more to keep up your required temperature. Installation of cavity wall insulation in homes will enable a more efficient usage of the energy which will ultimately cut UK’s carbon usage.

Being the most used room in a house, it’s little surprise kitchen extension are usually one of the most popular requests in the UK. They do not only open up a frequently used space in your home, but also goes a long way to add value to your property. However, to know the value that’ll added you must first determine the cost of building such an extension before moving forward. Generally, a typical kitchen extension will cost within the range of £20,000 to about £50,000 plus VAT, based on the size of your project as well as your location.

In reality, a single accurate cost of a kitchen extension will vary depending on a lot of influencing factors, one of which is the type of the extension. Let’s take a look!

✓ Rear extension. You may want to consider this type, if you do not have sufficient space for a side return. This will extend your kitchen into your garden which implies that you’re going to give up some green space to make this a reality. The average price to have this done in London will be about £30,000 or more including VAT, and about £20,000 plus VAT or more in other areas.

✓ Side return extension. This, normally, isn’t a huge add to your property, but will create a lot of space for your kitchen while also be a lot reasonable in terms of cost. This type will extend your home into an alleyway at the side of your property if any is available there. On average, the cost of the side return extension should be about £50,000 plus VAT in London and a lot less in the other regions.

If you’re considering converting a barn or buying one, you shouldn’t need to worry about it being cold. This is because building regulations dictate that when you convert a barn, you need to insulate it to meet specific standards. However, it’s worth considering its heating system and ceiling heights carefully – some barn conversions are likely to take longer and be more expensive to heat up than others.

Over the years, more and more home and property owners are beginning to realize the huge benefits that can be derived from loft insulation being a worthwhile investment. It’s quite worrisome the way in which energy bills have soared over the past 10 years and loft insulation is a considerable affordable energy efficiency measure that can go a long way to help increase your home’s energy savings.

As far back as the 1980’s, the standard when it comes to insulation thickness was 25 mm to 50 mm which was, at the time, considered to be sufficient. However, building regulations have changed the norm that now states that a new build needs to possess 270 mm of insulation in the loft in order to achieve the required u-value of less than 0.16/m2k based on the standard rock wool or sheep wool insulation.

Generally with loft insulation, there’s a law of depreciating returns which implies that the first couple of insulation centimetres will save you many times the cost of the installation, however an extra layer or centimetre is going to add less value to the point where it’ll no longer be wise or worthwhile to add any further centimetre. Therefore, with cheaper energy prices 30 years back, that additional couple of centimetres was not just worthwhile, but with the recent alarming rises in costs of fuel, that additional £10 savings per year has all of sudden changed to £30 which makes it become a lot more attractive.

If you already have 270 mm of loft insulation, regardless of the material you’re looking to add you’re most likely not going to benefit from a top up. The cost of the materials and installation will definitely be too high for the couple of pounds it’ll save you per year.

Cutting a plasterboard is a relatively simple process requiring only some basic tools. Unfortunately, the lack of knowledge serves as big deterrent for many people who wishes to put it to good use. Plasterboard can actually be sawn using an ordinary timber saw that’s fine-toothed to get a cleaner edge. However, the basic tools you may also need includes a sharp knife (Stanley Knife), pencil, a fine sandpaper, a straight edge and measurement tape as well as a wall board saw. Let’s have a look at the cutting process!

• Firstly, you need to put the plasterboard sheet flat on a firm surface.

• Use the tape measurement to measure the cut you wish to make.

• With the help of a pencil, simply mark out the part you wish to cut on the plasterboard’s front side.

• Once marked, place a spirited level over the marked spot on the plasterboard sheet you want to cut.

• Cut a shallow mark into the plasterboard sheet using the Stanley Knife to cut along the edge.

• The cut should be slow and gradual to ensure you do not wander off the edge of the marked area.

• Once the shallow cut has been made, turn the plasterboard sheet on its edge and deliver a quick and sharp push towards the plasterboard’s back and on one side of the cut.

• Place the plasterboard sheet backing against a flat surface ensuring the line of the cut is over an edge. Once done, give a quick and sharp push towards the back of the plasterboard sheet and on the part of the board is reaches beyond the edge.

• Using a fine sandpaper, remove all forms of paper burrs.

The process of cutting plasterboard requires a lot of practice. If you lack the training and experience, the cutting process is best left to a proficient professional who can guarantee the best results the first time and save you some additional costs due to potential damages.