Find a Builder you can trust in Hammersmith and Fulham.

How To Lay Loft Boards

Do you need more storage space in your home or property? If you live in a tiny space especially where extensions can’t be made sideways, why not look to the topmost area of your home and consider boarding out your loft to make it usable?

Boarding your loft can make for a fairly easy DIY project but like every other home improvement tasks, it requires some specific skill sets as well as knowledge for a successful construction. Therefore, we’d recommend you hire the services of a reliable professional in order to guarantee the best possible outcome, especially if you lack proper training or experience that’ll help you avoid some costly mistakes. Here, we’ll give you a good insight into the loft board laying procedures.

• Get The Right Tools & Equipment

The materials and supplies you’ll need to lay loft boards include loft boards, screws, tape measure and pencil, drill, hammer, saw, protective gear such as gloves and dust mask.

• Work Out The Area

Measure up the area you need the boards to cover. The standard loft features two different sizes (both are 18mm thick) which include 2400mm x 600mm and 1220mm x 320mm. You should ensure that the board you opt for fits through the loft hatch perfectly.

• Start Laying

Once you’re done working out the area, the next step is to put on your protective gear and start putting the boards in place. You should lay the boards in a staggered pattern so as to give a better strength. While doing this, watch out for any wire running through your loft so they don’t get trapped, you should also cut the boards for easy access to the light fittings’ top.

• Make It Permanent

Upon the successful placement of the boards in a way that offer a safe area to store things and stand on, you’ll have to screw them in place. Start by drilling 2 or 5 holes along the edge of individual boards in such a way that lines up with the centre of the joist below. Once done, then you can fix them in place with screws.

If you want to install an external wall, it is only wise to consider whether or not a planning permission is required in order to avoid a hefty fine. In a great kudos to the government and a welcome relief to home and property owners, the installation of external wall insulation is seen as an “improvement to the house and not an “extension or an “enlargement. Ultimately, this implies that external wall insulation fitting is to be done under permitted development and a planning application may not be required. However, like many other regulations, there are also exceptions to this rule and the main one is if the activity changes the appearance of your property. Properties such as a listed building having tighter regulations may pose some issues. As a result, we’d advise you to consult your local authority to ensure that there’s no fast rule to this topic before commencement of the external wall insulation project.

At the moment, according to the Government Building Regulations, the surface of the entire wall is to be improved to existing standards if the area to be insulated exceeds 25 percent of the wall. In normal situations this is usually the typical case, however to prevent avoidable fines and other possible punishments, it is always best to reach to your local authority and check out the rules guiding external wall insulation in your constituency. Furthermore, since external wall insulation is not a task that’s recommended to be done by yourself, you can also ask the professional external wall insulation fitting company for the applying rules before proceeding. As a good professional, the company should have a better knowledge of the rules and regulation guiding its activities.

Patios do not require lots of maintenance. They will only need occasional cleaning to make sure that the material keeps its original appearance. It's always best to clean your patio with a pressure washer and occasionally tap each slab or brick just to check the sand underneath hasn't washed away.

Pebble dash is an effective way to tune up your house or property as it can go a long way to enhance its curb appeal while also add to its resale value if you should decide to sell later on. Although, it’s highly recommended to leave this task for a reputable specialist, it’s also something that can be done as a DIY task. It must be states that this is a pretty difficult job and even more so if you haven’t attempted it before. In this post we’re going to take you through the processes involved in pebble dashing a wall. Let’s take a look!

• Mix up water with the lime strictly following the manufacturer’s instructions. Once done, leave it covered up to hydrate for at least 24 hours.
• Take one part of the slaked lime and mix it up with cement and six parts sand. This is to give the base mixture required to spread onto the surface.
• Use a trowel to apply the mixture onto the wall. Ensure that the trowel is level and use the edges to make a flat and smooth layer of the mixture on the surface as a base layer. Allow the base layer to dry for up to an hour. Then, rake the surface using a notched trowel and allow to dry for a minimum of 24 hours.
• Rinse and drain your pebbles. Then, set them under the wall you’re pebble dashing.
• Take the top coat of five parts sand and mix with one part cement and one part slaked lime. Use a trowel to apply this mixture over the base layer and smoothen it with the trowel to create a flat and even top layer.
• Spread a plastic sheet beneath the wall you’re pebble dashing to capture any loose pebbles as they fall.
• Grab the bucket of pebbles below the wall and scoop some of the pebbles up using a scoop or trowel. Some will stick and some will fall into the plastic sheet already placed below. Continue throwing the pebble dash until the surface is completely and evenly covered with pebbles.
• Lightly press and fit the pebbles on each section into the wall and leave for at least 24 hours to dry.

How To Plasterboard A Wall

If you’re looking to plasterboard your wall, one of the essential things to have in mind is that the plasterboard must be hung horizontally and not vertically. Due to the way they’re manufactured, plasterboard sheets normally possess a “grain along the length. This implies that, it’s only when they’re firmly placed perpendicular against the wall that they’re able to achieve their maximum strength. Materials you’ll need to complete this task includes: Tape measure, stanley knife, pencil, spirit level, drill driver or screw gun, surform, drywall screws and handsaw. Now let’s have a look at the wall plasterboarding steps!

• To plasterboard a wall the first step to take is to place each board in such a way to make the edges the centre of the noggins and upright. Also, the the adjoining walls and door openings should fit closely to the edges.

• Work from the door opening to the ending wall. From the the stud’s edge to the noggin’s centre, use your tape measure to measure a cut board and as a rule to mark up.

• Place your spirit level on the marks and use the Stanley knife to run a line along the intended cut. Once done, turn the board on its edge and give a sharp push on the back to split.

• Cut the paper left with the knife after folding the split edge back on itself. This way, you should get a nice and clean edge.

• In its right position, place the board up against the studwork. Install the screws on the board’s edges where a noggin or upright can be seen.

• Mark lines down across the board at the stud’s centre.

• Cut the end boards to length.

• Install the remaining boards as mentioned above. While doing this, make sure the factory edges are together.

• Cut any board extending into an opening and finish the edges using a surform.

We’d recommend you hire the professional services of a plasterer for the best results especially if you lack the necessary training or experience. Plasterboarding a wall can be a tricky challenge and you’d save yourself some time, money and effort by getting it right on the first trial.

Are you looking to pebble dash your house? This is a cool way to add a stunning new look to your home or property while also adding to its resale value should you wish to sell later on. The list of the benefits goes on, however one thing that most home and property owners would like to know before starting such a project is exactly how long it’ll take to complete it. If you’re also having similar thoughts, then you’ve come to the right place! In this post we’re going to give you an insight into the duration of pebble dashing a house. Let’s take a look!

First and foremost, just like any other home improvement project, the duration of a house pebble dashing project is affected by a number of variables. These variables include the size of your house, the company or contractor hired and lots more. In general, a house pebble dashing project should take within the range of 3 to 14 days depending on the size of your home. It should be noted that you’ll have to pay the workers on a daily basis. Most labourers will charge within the range of £140 to about £160 per labourer per day. And you should expect to have at least 2 labourers to work on your house’s pebble dashing project per day. On the other hand, the more labourer you have working on your project, the more you’re going to pay on a daily basis but this will also significantly reduce the time frame it’ll take to get the project over the line.

The answer is yes! Houses whose external walls have been insulated are more valuable than their uninsulated counterparts. And not only does it add to the value of a home, but also significantly reduces the amount of electricity consumption. This is a major turn on for potential investors which implies a greater demand and ultimately, a higher price. The real estate market is a very dynamic one which can be hard to predict at any particular time. The frequent changes in price are usually down to factors beyond the owners’ control, but if you’re looking to put up your house for sale in the near future, it would be a wise decision to consider ways in which you can increase its value. While renovating each room can be on the expensive side, a great solution would be insulate the external walls.

An insulated house is one that is well secured against the harmful impact of extremely high or low temperature, humidity and other atmospheric factors. Hence, the reason why a house with external wall insulation has a greater value which you would not want to miss out on. What’s more? You’ll get a great thermal insulation with the top notch materials like foamed polystyrene, high quality renders, mineral wool or polyurethane.

With an external wall insulation, you know the transaction will always be favourable on both ends. You get to smile to the bank, while the buyer also gets to enjoy great value for every penny spent. To employ the services of a reliable external wall insulation expert, simply conduct an in depth research from family and friends, online and other sources. Go through their online reviews and ask questions to become more familiar with the process and its value-adding potentials.

In the event whereby you’ve got big refurbishment ideas for your house but a small budget, then you know it’s time to be a bit more creative and apply some cheap and simple tricks. The best possible way to go about this is to invest time in acquiring new skills rather than trying to save up more money to pay a pro to deliver the results you want. After all, the most significant cost when it comes to house refurbishments is usually the labour cost.

The key to making cheap tricks a lot effective in the refurbishment process is by undertaking small tasks that’ll make a huge impact. A great way to start would be by taking it one task at a time rather than rushing to complete all at once. This way, you’ll have enough time to perfect your skills before moving on to the next.

✓ Paint the interior walls. Although this is a simple task but it’ll save you a lot of money if done as a DIY project. To get started, you’d have to text colour options by painting samplex on the wall first. Once done, you can go for the one that adds warmth, dynamism as well as energy to the room.

✓ Fix up your furniture. This involves re-upholstering and refinishing any piece of furniture that appears tired or overly worn (you can leave out the ones that you do not really like or unnecessary items).

✓ Spruce up small but important items used on a daily basis. This includes spray-painting inexpensive picture frames, recovering lampshades with a vibrant paper or patterned fabric, adding throw pillows to armchairs and couches and the likes.

✓ Fix all small things that are broken. This includes activities like patching the nail holes in the wall, repairing the latch on the kitchen cabinet, fixing the gutter, putting a new handle on the door and lots more.