Find a Builder you can trust in Lambeth.

A barn conversion is where an agricultural building is altered to serve a different purpose. Lots of barns conversion projects involve converting an old barn into one or more homes. However, barns can also be converted into other types of commercial building, like offices.

How To Fit Plasterboard

If you’re planning to renovate your house, then here is a must-read guide! Fitting of plasterboard is a crucial step when it comes to renovation. If you’re bringing down an existing lath and plaster for an upgraded surface or adding a new wall, a plasterboard is required for your project to be a true success. If you’re a novice with no prior practice or experience, you can protect your investment by hiring the services of a professional plasterer to guarantee the best results, the first time. However, we’ve put together this guide to give you an insight on how the plasterboard fitting process is done.

To get started, you’ll need a power drill, hammer, plasterboard nails or screws, broad knife, utility knife, measurement tape, pencil, ladder as well as a joint tape.

Before proceeding, you need to identify the number of plasterboard sheets needed to commence the project by measuring the height and width of the wall as well as calculating the square footage. If you possess a stud timber wall, the steps below will get you the best results.

• Measure the walls and mark the plasterboard where you’ll make the cuts. Start with a full sheet and cut pieces down in such a way that would fit

• Score the front paper of the plasterboard with utility knife. Fold the sheet to get a clean cut through the board and make use of the knife to the remaining paper.

• Place the first sheet against the wall and use an offcut to prevent the plasterboard from touch the floor.

• Make the plasterboard rest snugly against the wall in position and screw it firmly on each stud. Once done, fasten it at all the sheets’ edges and in a line down the stud to make for a firm connection. Follow the same process for the remaining plasterboard sheet till the wall is fully covered.

Many types of loft are suitable for a loft conversion. In general, you will need at least 2.3 metres of headroom in your existing loft. This is to make sure there is enough headroom after the conversion. Speak to a conversion specialist about the probability and possibility of doing this in your house.

Wall rendering is basically a process which involves the application of sand, cement or polymer covering to a home’s exterior in such a way that enhances its look while also offering an improved stability. The process is a perfect solution for several exterior concerns mainly due to the support its able to provide. It’s highly beneficial for older homes whose walls may suffer from poor quality because of wear over time, while it’s also greatly advantageous for newer homes as it increases their stability while also enhancing their visual appeal.

Knowing how to apply render is a great skill to have with your home’s upkeep in mind. The project can be done quite easily by any competent and confident DIYer. However if you lack any of those attributes, then we’d recommend you get in touch with a reliable professional for help. In this article, we’ll take you through the wall rendering process.

✓ Prepare the walls. This involves examining the wall, repairing any structural defects as well as stabilizing any movements to prevent the render finish from failing.

✓ External details. This includes the removal of bargeboards, rainwater, soil pipes, alarm boxes and all other external details.

✓ Insulation. In the event whereby external wall insulation is to be fitted, this is the stage to do so.

✓ Developing a foundation for the render to fix to. Apply a render mesh over the insulation, bedded into the first base coat layer of render.

✓ Building up the render.

✓ Render finishes. There are a wide range of colour options as well as various finishes available from very smooth to textured. However, you should note that thin coat render systems are usually designed to be self coloured.

✓ Final finishes. This involves the re-application of the external rainwater, soil pipes and the other external details.

If you’re planning to construct a kitchen extension on your property, one of the first things that comes to mind is whether or not you’ll require a planning permission before you proceed. Generally, kitchen extensions are normally classified as permitted development which allows you to carry out your project without any interruptions from the law or your local authority. In other words, if your extension is meets up with the guidelines of the permitted development rights, you won’t have to apply for a planning permission. However if otherwise, you’ll have to apply for a planning permission to your local council and may require additional reports. And regardless of your position, you’ll always need building regulations approval before you can carry out any kitchen extension project. It may also be required that you’ll have to issue a part wall notice if you’re to build on or close to the boundary with a neighbour.

If you don’t want to go through the hassle and stress involved in applying for a planning permission with your local council, then you must ensure the following:

✓ Your kitchen extension must not be over half of the area of land around your main house.

✓ The kitchen extension must not be side elevation onto a highway or forward of the principal elevation.

✓ The extension must not be taller than the highest part of the roof.

✓ The height of your kitchen extension must not go beyond four metres.

✓ Kitchen extension that’s more than one storey must not go exceed the rear wall of the main house by more than three metres.

✓ Two storey kitchen extensions must not be closer to rear boundary by anything less than seven metres.

✓ The kitchen extension must not include balconies, verandas or any raised platforms.

Finding a builder nearby can have enormous assistance when it comes to your build. Period on site, their familiarity of local planning permission, constructors’ dealers and other local trades are all vital bits of knowledge that you’ll welcome on site.

It is always wise to walk around in your local area or drive to a site where any construction work is going on. It’ll give you a proper impression of the constructors who are active nearby. You don’t have to like their style of work or the project they are currently carrying out – after all, a builder can only produce what’s on the plans in front of them.

Find a Builder Other Tradesmen Recommend

If you’ve had to call an electrician before or a local plumber and liked their work, you can always ask them if they have any builders whom they would recommend. Maximum tradesmen get used to seeing the similar acquainted names from one place to another in the sites they are working on and every so often has favourites for who they like to work with — and who they see as a good source of work.

Always Talk to Previous Customers

Once you’ve found a builder you would like to work with, ask them for a list of previous customers they have worked with; they ought to be glad to offer particulars if they’re self-assured they’ve done an effective job.

Look for a builder online

A decent place to start looking for builders online is on sites like the Federation of Master Builders. They have a search tool where you can find precise crafts in your area and look at their situations. All FMB members are assessed and individualistically examined and are checked to ensure that they have the correct insurances in place.

If you’re planning to build a single story house extension, this is one of the first questions that usually comes to mind to help you set a budget and start to make plans. But as simple as it seems, a single accurate answer can not be provided due to the fact that there are several variables that can play a key role in influencing the price of a single story house extension. These variables includes the size, location, design or specification as well as the build route. In this guide, we’ll provide you with a rough estimate that you can work with to put you on the right path.

The main determinant of the cost of a single storey extension is the size of the build, while the next most relevant factor is the quality of the finish you opt for. For a small extension, you can expect to spend a sum within the range of £14,000 to £17,000. Meanwhile for a larger single storey extension, if you opt for a large wrap around the extension with a great amount of glass to be incorporated in both the walls and roof, you can expect to pay a sum within the range of £80,000 to £120,000.

Overall, the average cost of a single story house extension is usually within the range of £34,000 to £37,000. For this price, you should get a standard sized rear or side extension which also includes the cost of a kitchen - it’s the most commonly use for a single story extension especially in the UK.

There are some additional costs you may also need to factor in to your extension budget. These includes surveys, architect fees, planning application fee (if needed), insurance and Party Wall Agreement (if needed).

When thinking about the right insulation material for your loft, some of the first few things that comes to mind is the various properties of that material as well as how good they fit with your home’s needs.naturally, you’d like to ensure that the insulation will be efficient enough to add to the overall energy efficiency of your home, however there are also other features that may not get as much attention but also happens to be equally important. As the primary function of an insulation is to blanket your house to offer a barrier against heat loss, going for an insulation material that’s also fireproof is crucial as loft insulation can burn. Although most insulation materials are fireproof, a myriad of problems can actually make your insulation burn.

For instance, fibreglass insulation is produced using glass combined with plastic polymers and is naturally resistant to fire. However, even at that you’d have to be careful with batts that are supported with foil or paper due to the fact that these materials can burn pretty quickly. Cellulose, on the other hand, is not fireproof and is required to be treated by other flame retardants in order to help reduce combustion. Some of the best insulation materials that are resistant to fire includes the following:

• Fibre glass. This is made of glass that’s spun into fibres, then combined using plastic polymers. As a result, fiberglass insulation is naturally resistant to fire.
• Mineral wool. Having a high melting temperature, this insulation material happens to be a great fit for thermal applications due to its superior fire resistant properties. In fact, mineral wool is still naturally non-combustible even if composed of recycled iron and steel by-products, or from actual mineral rock itself.