Find a Builder you can trust in Elland.

In general, you won’t need planning permission to install soundproofing. If you are installing soundproofing against a shared wall, you will usually need to follow the rules and restrictions set out in the Party Wall Act. In listed buildings and conservation areas, there may be extra restrictions on soundproofing.

How To Dot And Dab A Plasterboard

If you want a fast and simple way to achieve a smooth and sturdy wall which is decoration-ready, then dot and dab plasterboard is the way to go! It’s a relative simple process but can also be a bit challenging. Therefore, if you lack the necessary training or experience, hiring a professional would be a great step to protect your investment and guarantee the best results. Here, we’ll provide you with a deep insight into the plasterboard’s dot and dab procedures. Let’s have a look!

• At the thickness of the board with the adhesive, mark the ceiling and floor as well as the wall to indicate the centre of each board.

• Ensure the wall’s height is 15mm more than the plasterboard

• Make a mixture of the adhesive and achieve a thick consistency. Apply a consistent layer of the mixture around the wall’s perimeter, edge of the ceiling and any other openings with the use of a trowel.

• Select dabs that are about 250mm long and 50mm to 75mm wide and apply the adhesive in them. Make use of 3 vertical rows for individual boards. Also ensure to apply, at skirting level, a band of adhesive.

• Position the board’s reverse side against the dabs, and laying against the packers. Then make the board align with the ceiling and floor marks with the help of a straight edge.

• Raise the board till its tight against the ceiling with a board lifter. Once done, use the plasterboard to wedge the board into place before you remove the board lifter.

• Repeat the same process for the remaining parts of the room. Once completed, make sure the adhesive is set before you remove the boards.

It’s often said that a garage conversion can take anywhere between 1 week to 1 month, depending on the size and scope. But many standard conversions without any plumbing can take as little as 5 days. Your contractor will be able to tell you exactly how long your garage conversion will take.

In some cases, it’s possible to convert a basement into an apartment. This can be a great way to incorporate an additional dwelling into your property and increase its value. However, converting a basement into an apartment can be quite expensive and time-consuming.

As with any type of dwelling, you’ll need to think about basic things like access, damp proofing, ventilation, insulation, heating, electrics, plumbing, lighting and décor. If you’re planning on extending your basement, then you’ll also need to ensure that your property is sufficiently supported.

It’s a good idea to consult a professional, like a basement conversion building specialist, to find out how feasible your project is before you go ahead with it.

A double house extension is basically a construction to any aspect of your house that elevates up to offer two floors of space. It can be structured to suit your existing home in two storeys or as a side wing on a taller property. If you’re considering building a double house extension, then estimating the cost is a very important task to do before commencing the project. In this article, we’ll give you an idea of the cost of a double house extension so you can estimate yours accordingly.

The double house extension cost depends on several factors that’s specific to your home as well as your design choice. These includes:

• Location of your property. Places like London and the southeast will generally cost more than the other regions due to higher demands.

• Accessibility of the site. The ease of your site’s accessibility also plays a key role in the price.

• Size of the extension. The more the extension’s size in footprint and square metres, the higher the possible costs.

• Materials used in making the roof as well as the complexity of the roof design.

• Your choice of finishing. These includes flooring window and door frames, glazing, underfloor heating and roof lights.

• Your property’s soil type. Different types of soil requires varying treatments as well as materials to develop solid foundations.

Constructing a double house extension is a quite simple build in terms of technicality when its to the side or rear of your house as this can also help you save some money. Generally, considerably expanding your home’s space by building a double house extension will cost within the range of £1,500 per m2 to about £2,800 per m2.

Aside from the cold weather not being the most pleasant condition to work in, the winter weather can also cause a lot of problems for construction workers and even more so when you’re working with render. Poor weather conditions can generally cause a lot of harms on the final finish of a render. Below are some of the reasons why you should not consider rendering in a bad weather.

✓ Lime bloom. Render can be impacted by lime bloom as they are subjected to damp conditions and low temperatures while curing. This is due to the fact that cement are intolerant to slower drying conditions especially immediately affect its application.

✓ Top coats can be compromised. Coating are likely to get washed off before they’re even afforded the chance to set if drying conditions are low.

However, because its cold out there doesn’t necessarily imply that work must stop. It’s very possible to render during the winter months but to avoid potential pitfalls, we’ve got some tip that can be of great help. Let’s have a look!

✓ Check the weather forecast. Determine the drying and curing time and watch the forecast for the temperature dropping at night.

✓ Select the most suitable render. There are renders that are suitable for application in low temperatures to about 5℃ or even as low as 1℃. These types of render are fast setting which makes them perfect for the cold condition.

✓ Watch out for frost. Frost and render are enemies. Therefore, it won’t be wise to work with frosted materials, on frosted subtrates or apply below the recommended temperature that’s written on the product’s datasheet.

✓ Protect the finish. Make use of artificial enclosures around the scaffolding to battle adverse weather conditions.

There are many different types of extension. For example, you could install an orangery, flat or pitched roof extension, over-structure extension, single or double storey extension or a glass box extension. Which one of these is most suitable will depend on your existing property.

In recent times, more and more home and property owners are starting to come to terms with the large returns and little investment in cavity wall insulation provides. For a relatively little amount you can achieve a lot, from an increase in your home’s energy efficiency and reduction in heating bills to a huge boost in your property’s resale value and lots more. This makes you wonder how an ordinary insulation can help you achieve so much, right? Well, you’re definitely not alone! Several other potential investors are also eager to know exactly how the cavity wall insulation works to deliver all these juicy benefits. In this post, we’re going to go provide you with a detailed insight on how cavity wall insulation works. Let’s take a look!

Typically, cavity wall insulation works as acting as a shield which prevents the escape of heat from your home. It features a reflective surface which serves as a barrier to reflect heat from one side of the panel, effectively minimizing the amount of heat conduction that escapes through. This protection of your home from heat penetration comes with a couple of benefits with the obvious one being an incredible thermal efficiency. An insulated home or property is able to maintain a much more balanced temperature throughout the year – staying a lot cooler during the summer months and retain the heat generated during the winter months. However, a less talked about benefit is the fact that when an insulation is done during the construction of a house, the whole development phase can be completed a lot quicker. This is mainly because insulation offers total protection against weather conditions which enables internal trades to continue without the need to wait for brickwork or cladding to be completed.