Find a Builder you can trust near you.

Is there a hole in your asphalt driveway you feel you can repair yourself? If it’s something you know you can confidently do then this step by step guide is just for you. If otherwise, then we’d recommend you hire the services of a reliable professional who can guarantee the best results while also saving you some time and extra money that could result from possible errors. In this article, we’d go over the reparation process of an asphalt driveway with a hole in it.

✓ Get the necessary tools. You’re going to need a broom ( to clean the area), caulking gun ( to fill the hole), a hand tamp a plate compactor or a hammer ( to level the filled in hole) and a weeding glove (just in case there are weeds growing in the hole).

✓ Prepare the area. Do this by weeding the plants or weeds that might have grown inside the hole and identify your asphalt filler.

✓ Wet your soil, if necessary. It’s important to note that this is only necessary if your soil is dry to help the filler stick properly.

✓ Fill in deep holes. If the hole goes down about 3 to 4 inches or more, simply fill it with any material like rocks, clay etc.

✓ Apply the asphalt filler. Fill the hole with the asphalt filler to about half an inch higher than the surface of the driveway.

✓ Level the filler. For a large hole, make use of a plate compactor or a hand stamp, but a hammer will be sufficient for smaller holes.

✓ Cover the hole, if necessary. If your home isn’t level, covering your hole with a piece of plywood is advisable.

✓ Clean off the seal. After the asphalt looks done and in place, simply brush away the debris from the seal to finish off the project.

With the prices of buying a house skyrocketing, many of us are tempted to building our own house. This is sometimes an excellent choice, but you will first need to understand the costs of building a house from scratch. As per a general estimate, the cost of self-build ranges between £300 per m2 to £3,000 per m2.

As you can see, this is quite a variation in price from lowest to highest. Location is a prime factor in determining the costs. Building a house in London and the South is more expensive compared to other regions. Aside from location, several other factors make up the price.

Self-manage with subcontractors

You hire professionals directly like builders and carpenters. You also buy all the materials yourself allowing you to get the best prices.

Hiring a main contractor with other subcontractors

You will first need a main contractor who will help to create the watertight structure for your house. For the rest of the work, try hiring out subcontractors. Make sure that you buy all the materials yourself to get the best price.

External cladding materials

If you are looking to install other external material other than brick, you will also need to factor in the cost for the same.

Here are some example prices:

• Render on blockwork costs around £25 per m²

• Timber cladding is around £25 per m²

• Hand¬made all-weather tiling costs around £54 per m²

• Rubble walling or flint is around £90 per m²

• Reconstituted stone costs about £48 per m²

• Natural stone is about £75 per m²

Make sure to include these costs when coming up with the estimate.

Roofing materials

Non-standard roofing materials tend to add more to the cost and therefore you will also need to account in for this factor.

Here are some examples:

Welsh slate – £60 per m²

Second-hand slates – £35 per m²

Handmade clay tiles – £65 per m²

Reed thatch – £80/m²

If you choose to add any unique material to your roofing, be sure that you remember to factor in its cost.

For 2 metre solid fences it’s recommended to use concrete posts to support each panel. For smaller 1 metre fences or for picket fences with gaps between each timber piece you can use timber posts. A fencing contractor will be able to advise you on the best materials from the length and requirements of a new fence.

How To Plasterboard A Wall

If you’re looking to plasterboard your wall, one of the essential things to have in mind is that the plasterboard must be hung horizontally and not vertically. Due to the way they’re manufactured, plasterboard sheets normally possess a “grain along the length. This implies that, it’s only when they’re firmly placed perpendicular against the wall that they’re able to achieve their maximum strength. Materials you’ll need to complete this task includes: Tape measure, stanley knife, pencil, spirit level, drill driver or screw gun, surform, drywall screws and handsaw. Now let’s have a look at the wall plasterboarding steps!

• To plasterboard a wall the first step to take is to place each board in such a way to make the edges the centre of the noggins and upright. Also, the the adjoining walls and door openings should fit closely to the edges.

• Work from the door opening to the ending wall. From the the stud’s edge to the noggin’s centre, use your tape measure to measure a cut board and as a rule to mark up.

• Place your spirit level on the marks and use the Stanley knife to run a line along the intended cut. Once done, turn the board on its edge and give a sharp push on the back to split.

• Cut the paper left with the knife after folding the split edge back on itself. This way, you should get a nice and clean edge.

• In its right position, place the board up against the studwork. Install the screws on the board’s edges where a noggin or upright can be seen.

• Mark lines down across the board at the stud’s centre.

• Cut the end boards to length.

• Install the remaining boards as mentioned above. While doing this, make sure the factory edges are together.

• Cut any board extending into an opening and finish the edges using a surform.

We’d recommend you hire the professional services of a plasterer for the best results especially if you lack the necessary training or experience. Plasterboarding a wall can be a tricky challenge and you’d save yourself some time, money and effort by getting it right on the first trial.

If you want to install an external wall, it is only wise to consider whether or not a planning permission is required in order to avoid a hefty fine. In a great kudos to the government and a welcome relief to home and property owners, the installation of external wall insulation is seen as an “improvement to the house and not an “extension or an “enlargement. Ultimately, this implies that external wall insulation fitting is to be done under permitted development and a planning application may not be required. However, like many other regulations, there are also exceptions to this rule and the main one is if the activity changes the appearance of your property. Properties such as a listed building having tighter regulations may pose some issues. As a result, we’d advise you to consult your local authority to ensure that there’s no fast rule to this topic before commencement of the external wall insulation project.

At the moment, according to the Government Building Regulations, the surface of the entire wall is to be improved to existing standards if the area to be insulated exceeds 25 percent of the wall. In normal situations this is usually the typical case, however to prevent avoidable fines and other possible punishments, it is always best to reach to your local authority and check out the rules guiding external wall insulation in your constituency. Furthermore, since external wall insulation is not a task that’s recommended to be done by yourself, you can also ask the professional external wall insulation fitting company for the applying rules before proceeding. As a good professional, the company should have a better knowledge of the rules and regulation guiding its activities.

What is your garage being used for? If your answer is anything besides your vehicle, you’re in the majority in the UK. In the country, according to a research by Admiralty Loans, several home and property owners now use their garage as dumping ground for all sorts of stuffs asides a car. Ultimately, this gives rise to garage conversions as the more or less underutilized space can be converted into a living space which can be more beneficial while also adding more value to the property.

A garage conversion is a fast and relatively affordable route to adding more floor space within your home. It’s basically the act of changing your garage into something other than a storage or a place in which you can park your car. This can be anything from a bedroom to a playroom and anything in between. It’s a great way to provide extra space to allow your family to spread out and have more privacy while still within the walls of your home.

A garage conversion project is a huge one which mostly does not require a planning application so far the conversion is internal. However if you’re planning to increase the garage’s size or change the exterior of your home, or convert your garage into a separate room, then you may require a planning permission before getting started. It’s always wise to consult your local authority before carrying out any work to be on the safer side.

A project of garage conversion’s magnitude is better left to a reliable professional who have the experience when it comes to dealing with building regulations and more. This way, you’d also get to save yourself some headaches and some extra cash which may result from possible costly errors.

In some cases, it’s possible to convert a basement into an apartment. This can be a great way to incorporate an additional dwelling into your property and increase its value. However, converting a basement into an apartment can be quite expensive and time-consuming.

As with any type of dwelling, you’ll need to think about basic things like access, damp proofing, ventilation, insulation, heating, electrics, plumbing, lighting and décor. If you’re planning on extending your basement, then you’ll also need to ensure that your property is sufficiently supported.

It’s a good idea to consult a professional, like a basement conversion building specialist, to find out how feasible your project is before you go ahead with it.

Rendering is an external wall’s plastered finish which provides a smooth finish while also protecting the brickwork from the elements like rain, snow and the likes. The traditional rendering is normally applied in two or three coats which enables it to be more resistant to surface cracks. In modern times, the finishes are largely different from the grey pebble dash of post war housing. Today, we now have a plethora of specialist products to pick from such as through-coloured silicone renders as well as one coat renders. The types of renders include the following:

✓ Cement renders. These are the common option that are usually mixed on site and used in a number of applications, then painted when dried. There’s a need to paint this type of render regularly to keep them looking great.

✓ Polymer renders. These are pre mixed and mostly pre coloured (usually with through colouring).

✓ Through-coloured products. These rendered do not need to be painted as the pigment is already added in the manufacturing process to colour the whole render.

✓ Lime renders. These are superior to cement as they’re less likely to trap moisture in the brickwork and also more good looking. However, they’re generally more costly and more difficult to apply.

Overall, rendering on a house provides several benefits. Not only is it able to protect your brickwork against the elements like the rain and wind, but it can also make the building more efficient. Being fully aware that about 30 percent of the energy used in heating a home is lost via the external walls, making use of a product such as acrylic insulated render is a smart approach to improve your home’s energy efficiency without affecting your interior living space.