Find an Electrician you can trust near you.

Also commonly referred to as a consumer unit in recent times, a fuse box is responsible for controlling and allocating of the electricity in your home. They hold the power any time there’s an overload in one of the circuits which in turn, prevents fire as well as electrical damage. Fuse boxes are often incorporated in homes but consumer units are very rapidly replacing them. Therefore, when your fuse box breaks down, it’s always a smart decision to replace them with consumer units due to the fact that they’re safer and also comply with building regulations while also being a lot easier to use. If you’re extending your home, upgrading to a larger capacity model enables you to make use of more power with the power overloading. In this post, we’re going to cover the amount you’re expected to pay to replace or install a new fuse box or consumer unit as well as the factors that may affect the cost.

For a 10 way dual RCD consumer unit, the typical cost range will be between £250 to £600, meanwhile 15 way dual RCD consumer unit should cost within the range of £300 to £700. Overall, the smaller the house, the fewer the circuits that’ll be needed, hence the difference in the aforementioned prices.

There a number of factors that can affect the cost of replacing a fuse box. These factors includes the the size of the house in question ( the bigger the house , the more the circuits there are and the bigger the fuse box needed), the location ( for instance, places like London where there are higher demands are likely to be more expensive than other regions ).

It might be possible to fit electrics in your shed, depending on where it is and what it’s made of. You should get in touch with a qualified electrician to find out whether it’s possible. Never attempt to run electrical cable from your house to an outbuilding!

Most domestic solar thermal panels do not need planning permission and are covered by permitted development rights. There are restrictions on the size and location of these systems. If you live in a conservation area or listed building, or want to install a very large solar thermal system, check with your local authority to see if you will need planning permission.

The importance of selecting the right size battery for your home simply cannot be overemphasized. A lot of home and property owners are facing this challenge and understandably so. Selecting the right battery size for your needs depend on a number of factors which includes your motive for adding a battery, your electricity usage, your budget as well as your panel array size, be it new or existing. In this post, we’re going to take you through some of these factors to help you determine the right battery size for your home or property. Let’s take a look!

• Your motive for getting a battery. While most people purchase a battery to wipe out their need to purchase electricity from the grid with the hope of making some savings, others add a battery so as to enjoy backup power. There are also some who just needs it to power their home with solar energy. It’ll not be economical to size a battery to effectively take you off the grid, but if your motive is to make savings, then you’ll should expect to purchase some electricity from the grid during the year.
• Electricity usage. The average household uses about 16kWh of electricity on a daily basis. During the daylight hours, most of these household will use a third of their electricity when the solar panels are still generating electricity, while the remaining two third are purchased from the grid. In other words, you’ll require a minimum of 10kWh battery capacity if you were to use a battery to power the electricity you purchase from the grid.

For a typical British household, you’ll most likely need a 5kWh solar power system which normally generates about 17 to 21 kWh on a daily basis depending on your location in the UK.

Can You Replace Storage Heaters With Electric Radiators?

The short answer to this question is yes. If your outdated storage heater is not heating your home the way it should, you’ll find a better replacement in electric radiators.

Being more modern and efficient, electric radiators offer a wide range of benefits which storage heaters can only dream of. Let’s have a look.

• Unlike storage heaters, electric radiators do not need to be charged up the night before which makes it totally controllable as you do not have to guess what your heating needs will turn out to be the next day.

• The above benefit leads to an even better one as the controllability quality of electric radiators makes them a lot more efficient than storage heaters. Electric radiators usually comes with programmable timers and thermostats which allows you to set various heating schedules for each of your rooms, meaning you’re only heating when and where its needed.

• Unlike some storage heaters, electric radiators do not cause wall blackening and also happen to more elegant and stylish.

• Electric radiators are not tough on allergies like storage heaters as they do not depend mainly on convection to heat

• Electric radiators also have an easy installation process with all you need to do to switch from storage heater to one being the removal of the former and inserting the radiators into the sockets.

However, if you want to make a switch to electric radiators, there’s the need to change to a standard electricity tariff from your economy tariff. And while the standard electricity tariff rates may be more expensive than the night time rate provided by Economy 7, the standard tariff rates are a bit cheaper than the daytime Economy rate. You’ll also get to use much less of electricity while also saving money on your heating bills and more.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.

Unlike in houses constructed in the 1960s, where you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type, majority of houses built in the 1970s would not need to be rewired. Most often than not, what they’ll need is just a consumer unit as well as an earthing upgrade. If you happen to have a consumer unit change, the electrical professional you hire would have to inspect the most parts of the property regardless. With that answered, you may also wish to know just how often a house would need to be rewired.

First and foremost, in order to make sure that your wiring is safe there’s a need to ensure that a periodic inspection is carried out by a fully licensed and qualified electrician every 10 years. Meanwhile for rental properties with tenants, the landlord is required to carry out a periodic inspection at least every 5 years. This will make sure that the electrical works in the property are safe, up to date and suitable for continued usage.

In order to determine whether your house needs to be rewired, there are some signs or indicators you’d have to watch out for. If you notice one or even a combination of the following , then you should get in touch with a registered electrician:

• Discoloured outlets and switches
• Persistent burning smell
• Outlets problems
• Flickering lights
• Tripping circuit breaker or blown fuses
• If you happen to possess aluminium wiring
• If you have continually experienced electrical shocks

It must, however, be said that rewiring a house is a messy and quite disruptive work. It’s also considered to be quite dangerous and recommended to be carried out only by a professional is well trained and experienced when it comes to tackling electrical works.