Find a Heating Engineer you can trust in Chelmsford.

The Oil Firing Technical Association or OFTEC operate a competent persons scheme to certify installers. It’s always recommended to use an installer with this certification as it proves they have the training and expertise to properly install your boiler and give you realistic advice on the efficiency of your system. Also, OFTEC registered installers offer Workmanship Warranties to protect you if there are any problems after installation.

Modern oil boilers do not require a lot of maintenance. OFTEC recommends that oil boilers are serviced and inspected every year. This keeps them running as efficiently as possible and will ensure any issues with your boiler are identified before they cause bigger problems. This servicing is also vital because of the increased risk of carbon monoxide leaking from a poorly maintained boiler.

Do British Gas Service Oil Boilers?

Are you interested in finding out whether or not the British Gas service oil boilers? Well, you’ll find the answer in this article! The British Gas engineers are able to repair several types of boilers such as home based combi, conventional as well as system boilers. Unfortunately, they do not fix oil boilers, electric boilers or solid fuel boilers, but if you possess a gas boiler that’s more than 70kW which is mostly present in commercial premises or large buildings you can give them a call.

For a yearly boiler service British Gas engineers will provide the following solutions to ensure central heating and boiler are both in proper working condition and also absolutely safe.

• Inspection of your boiler for possible leaks and corrosion.

• Detach your boiler casing to ascertain the proper functioning of it’s main components.

• Clean up all parts as necessary

• Attach the casing back to the system and make sure its well sealed

• Inspect the level of the gas pressure to ensure that it’s at the right level.

• Perform a flue check to determine that the are no toxic gas emissions like carbon monoxide being discharged by your heating system.

Upon completion of the annual boiler service, the British Gas qualified engineers will then drop a checklist with you which is going to include all the relevant information you may want to know about your boiler system.

In some cases, British Gas engineers may be able to complete the entire boiler service in one visit. However, it all depends on the problem that’s discovered (if any). They may not possess the required part to fix the problem with them, so they’ll have to order it from the British Gas national distribution centre. Most times, this part will get to them the next day so they can finish their tasks as soon as possible.

Many domestic biomass boilers are no bigger than a standard gas boiler. However, they do require a flue, a feeder and a space to store the fuel. These can be designed to suit many different properties and will fit in lots of homes or a garage or outbuilding.

How Much Does It Cost To Move A Gas Meter?

When your gas meter is not in the right location while completing your renovation works or extending your property, it can be a worrying experience.

As a homeowner, you’re not allowed by the law to move your gas meter by yourself - it’s a very dangerous task that’s too risky to undertake just by watching a Youtube video or reading a blog post. Moving of a gas meter can and should only be carried out by a qualified and licensed gas supplier. And this, ultimately, gives rise to the question - how much does it cost to move a gas meter? Before we provide an answer for that, let’s look at what moving of a gas meter entails.

First and foremost, moving of a gas meter typically involves switching off the gas source to your home or property. The pipeline about 2 metres away from your property would be cut into for safety reasons and diverted into another position. Furthermore, you can as well apply that your meter should be re-fitted and re-linked to the inner copper pipeline, but that’s if the inner copper pipeline happens to be within two metres of the new location of your gas meter.

The time involved in the completion of a gas meter re-location project depends largely on the complexity of the job as each project is unique. Typically, the standard timescale from preparation to the final stage of moving a gas meter will take between 4 to 8 weeks. Finally, how much will it cost to relocate your gas meter?

As there are no government funds to subsidize gas meter relocation costs, this can be a very expensive work to carry out. Generally, the price to move a gas meter of about 5m will start within the range of £640 to £670.

Are Electric Radiators Expensive To Run?

Just like many home additions, the running costs of electric radiators varies largely on a number of factors. Great number of electric radiators typically comes with an in built thermostat which is designed to turn itself off automatically when not in use in order to save energy.

However the energy provider’s set electricity charge tariff will also have a great influence on an electric radiator’s running cost. Let’s take a look at the running costs of an electric radiator!

A 600 Watt electric radiator ( on a standard electricity tariff) will usually have a running cost ranging between 4 to 6 pence each hour. However you should also take note that this scenario might change in situations whereby the electric radiator is not calling for heat the full 60 minutes of each hour. And this is more likely to be the situation as the thermostat is programmed in such a way that enables it to turn itself off immediately there’s an achievement of your required room temperature level - usually within 10 minutes from the time it was switched on. As a result of this, the running cost per hour of electric radiators will be greatly reduced to just about 1 to 2 pence.

It’s also important to note that enhancing the insulation of your home can go a long way to add to the heat retention value of each room. Consequently, the duration at which the electric radiator calls more heating will be significantly reduced, which in turn, implies a lower electricity bill.

Another key factor that can play a huge role in saving on your heating bills is the programming as well as usage of your electric radiators. Every radiator comes with an independent digital thermostat with a number of 24/7 programming options to help achieve maximum efficiency. When the radiator is properly set according to your lifestyle, you can save as much as 50 percent on your heating bills.

What Size Of Electric Boiler Do I Need?

If you’re thinking about installing central heating in your home or property, you’ll be shocked by the plethora of options that’s currently available in the market as regards the boiler type that can be installed. Being a very good alternative to gas boilers or an oil or LPG boiler, electric boilers are here to stay. They usually feature different power outputs which tends to lead to one of the most frequently asked questions about electric heaters - what size of electric boiler do I need? Here, we’ll give you a good insight into sizes of electric boilers available to help you make the right decision.

The importance of getting the perfect size of electric boiler for your home can not be over-emphasized. If your electric boiler size is too small, it won’t be able to provide the level of heat and hot water required. And on the other hand, if it’s too big, it’ll definitely consume more electricity which would be a total waste of money.

To determine the correct size, if you have a wet central heating or water radiators in your home, you’ll need to calculate the boiler’s capacity required to operate them and allow 1.5kw per radiator. To be more accurate, it’s advisable to talk to a professional installer to avoid making a costly mistake. Every professional installer should have an idea of the appropriate size of electric boiler that’ll be needed given your special requirements and home size.

Generally, with a 12k kilowatt boiler, you should be able to operate up to 7 to 8 radiators which is good for smaller properties. For apartments and flats, getting a smaller electric boiler would be the best option.

Condensing boilers are the in-thing when it comes to modern heating systems in UK homes and across the globe for a good reason. This is primarily due to the fact that condensing boilers happens to be highly efficient as it enables the fuel you’re burning to heat up your home go a lot further. Having a new high efficiency condensing boiler rather than an old G-rated non condensing boiler will not only enhance your heating controls, but also save you a lot of money annually. In this article, we’re going to take you through the basics of a condensing boiler. Let’s take a closer look!

If you’re interested in getting a greener and more efficient boiler, you simply can’t afford to look beyond a high efficiency condensing boiler. This is purely due to the fact that these condensing boilers happens to make a better use of the heat they’re able to produce from burning fuels like oil or gas ( in other words, they require less heat from the burner, which makes them a lot more efficient).

So how does a condensing boiler work? Unlike a non-condensing heat-nly boiler, some heat will be wasted in form of hot gases which are released from the flue. Meanwhile a condensing boiler captures some of the heat from these gases and puts them to use for heating up water that’s coming back from your central heating system. As a result, it requires just a minimal heat from the burner which make the boiler more efficient.

You should take note that all new modern boilers are condensing boilers. Therefore if you’re planning to replace an old boiler with a new one, you’ll definitely be buying a new condensing boiler and benefit from all the efficiency and savings that comes with it.