Find a Heating Engineer you can trust in Abbots Langley.

The Hive thermostat stand is relatively easy to install, however if you lack the necessary training or experience, this is a task you might want to leave to a professional to guarantee the best result while also saving you money and time. This guide will give you a good insight into the Hive thermostat installation process.

The installation of a Hive thermostat does require it to be connected to your home boiler. For this reason we always recommend you get a professional to install it. However once install the Hive Smart Thermostat is very easy to operate and move the controller around your home. To get started, you can follow these steps:

• Press the lever at the lower side of the thermostat and pull away from the front to detach the back plate of your device.

• Once done, simply hang the thermostat on the stand back plate and ensure it holds firmly in place

When it comes to Hive thermostat installation, you might also want to consider the positioning of the device in such a way to heat your home even more efficiently as its designed to be very sensitive to temperature. To identify the best spot for your Hive thermostat, let’s take a look at some of the dos and don’ts.

A Few Dos:

• Do maintain the position of your Hive Thermostat to keep a stable connection with the receive and Hive Hub.

• Do ensure that the position chosen is the centre of your home or a frequently used room.

• Do place the thermostat about 1 to 1.5 metres from floor.

• Do ensure that your thermostat is in a close proximity with the hub and receiver for a better functionality.

A Few Don’ts:

• Don’t place your Hive thermostat stand close to radiators, direct sunlight or other heat sources,

• Don’t position your device near or at places that can expoerience a sudden change in temperature such as the front or back door.

• Don’t leave your thermostat too close to curtains or ornaments.

In recent times, home and property owners are constantly looking for ways in which to enhance both energy efficiency and sustainability especially as the world draws closer and closer to energy-efficient technology. The Nest thermostat is a great example of this fact as its designed in such a way to save energy while also cutting heating and cooling costs. And an interesting fact is, you’re not limited to using just a single Nest thermostat in your home as multiple of the device can successfully run together to maintain a consistent level of temperature monitoring as well as energy efficiency. What’s more? You can add up to 20 Nest thermostat and 18 temperature sensors in a home.

It’s very unlikely that you’re going to need this many thermostats in your home, but if you’d like to add a second the process is quite straightforward. However, we’d recommend you employ the services of a seasoned professional especially if you lack the required training or experience to pull this off to save yourself some time and money.

To get started, simply download the associated Nest app to add Nest devices. Now let’s have a look at the processes involved in adding a second Nest thermostat to your home.

• Open the app.

• Go to the top left corner of the main screen and click on the menu button.

• Pick the location or home you’re adding the device to.

• Go to the top right corner and select the “settings.

• Once done, then click on the Add Product “Plus button.

Upon a successful addition of the second thermostat, the app will guide you through the initial set up steps. Google also offers a very helpful guide if you’re unfamiliar with the initial configuration.

How To Fix A Boiler

A boiler is subjected to regular usage, working for a several hours a day and providing hot water for shower on a daily basis and even more so during winter. With it’s power and efficiency, we tend to postpone or even totally overlook its maintenance. However, no matter how good your boiler is, it consists of many moving components and it’ll certainly develop some faults some day. When the inevitable occurs, you might want to save some money and get it fixed all by yourself.

When it comes to fixing boilers, seeking help from a licensed heating engineer is usually the best solution, however at times you might be just lucky to be faced with minor issues which you should be able to handle yourself. In this article, we’ll look at some of the most common causes of a broken boiler and how you can get your heating system up and running again. Let’s have a look!

✓ Low system pressure. In the event whereby your boiler display a low system pressure, it could mean that the system is about to breakdown. You’ll have to carry out regular inspections on the pressure gauge to see if there’s any noticeable changes and call in a heating engineer immediately to prevent a system breakdown from happening.

✓ Poor heat production. Although this is unlikely to lead to any great issues, but it’ll reduce the effective functioning of your heating system. To prevent a debris build, it’s important to have your boiler cleaned regularly.

✓ Strange noises. Boilers often make noises, so there’s nothing to worry about unless it’s a banging or whistling noise that’s very odd , then there may be a serious issue. You’ll have to check the air intake, pressure, exhaust and piping to ensure they’re working just fine, if not there may be a need for replacement.

Who Fixes Boilers?

With boiler running for several hours in a day and working hard to ensure that our home stays warm, even when we tend to take it for granted it’s always there give us the heat we need whenever we need it. So in the event whereby the inevitable happens and your boiler breakdown, which professional is the most suitable to call for help? When the pressure is on to stop a boiler leak or bring back warmth to your home, knowing who to call can make all the difference.

When you need a professional to fix your boiler, the right professional to call is a heating engineer. Heating engineers work mainly on heating I both homes and businesses, so you’d be right to call them specialists in all heating matters. As a result of this, you may want to give them a call when experiencing some issues with your boiler as they’d be in the best position than any other professional to give you a proper solution.

Generally, heating engineers are experts when it comes to fixing boilers and can help with various tasks such as installing a new boiler, boiler repairs, installing new gas pipes, repairing gas leaks, changing radiators, fixing leaks, installing heating controls and many more. What’s more? A boiler repair has to do with working with gas and before you can do that you must be a Gas Safe registered engineer as required by the legislations in the UK. In other words, any gas boiler related issue must be tackled by a Gas Safe registered engineer as this is a very dangerous fuel in which the services must be provided to highest standards of safety. Only heating engineers can be a Gas Safe registered engineer to work on gas boilers.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

If you’re thinking about getting a new gas boiler for your home or property, then you might also be wondering how much it’ll cost you so you can set a budget and start planning. As simple as this question sounds, it’s actually very tricky to provide a simple and short answer as the costs of installing a new gas boiler alone varies greatly based on the parts needed, the amount of work required, your location, their availability as well as the company you hire for the project.

When it comes to purchasing a new gas boiler the price you’re expected to pay also depends on multiple influencing factors such as the type, brand as well as your most preferred gas boiler model. However, one thing you should have in mind is the fact that your gas boiler is right at the heart of your home or property and can be a complicated piece of machinery. As a result, you wouldn’t expect gas boilers to come cheap. Generally, it’s going to cost within the range of £500 to about £2,500 to get a new gas boiler. Therefore, it’s always advisable to obtain all necessary details and facts before you decide to purchase a replacement gas boiler.

This price range may seem too high as it’s usually a turn off for most homeowners. However, it’s worth noting that gas boiler replacement costs and gas boiler installation costs are, more often than not, compensated by the saving you’ll make off your utility bills - all thanks to the new and more energy efficient boiler you just installed in your home. And even more importantly, when it has been estimated that roughly half of the amount spent on energy on an annual basis depends on your boiler.

During the cold months ( winter), there’s a high chance for a more frequent occurrence of faults and breakdowns of your boiler as this is the time in which more strain is being placed on the device. Unfortunately, this is exactly the time in which you’d wish to derive maximum benefits from your boiler to keep you warm all through the winter. As a result, home owners are given no other option than to pay the mega boiler repair bills to keep themselves warm and cosy all winter long. There is, however, an option which can greatly soften the blow and that’s having a boiler breakdown cover.

Boiler breakdown cover provides coverage for cost of hiring an engineer to get your boiler back to a top condition while also paying for the parts as well as labour needed to resolve the boiler’s fault. To select a boiler breakdown cover, you should take into account factors like whether or not the policy provides coverage for limited or unlimited call-outs within the coverage period. You should also ensure to go through the terms and conditions of the cover if you can stake a claim if your boiler were to be damaged by a different thing in your central heating configuration or a persistent fault.

There are an array of boiler breakdown package types with little differences which relates to one or more of the following:

• The package monthly cost

• The call outs excess to be paid

• The nature of the helpline. It may be a 24/7 service or just a few selected hours of the day.

Therefore, to answer the question of which boiler breakdown cover, you’d have to compare the different packages to determine the most suitable one for both your needs as well as pocket.

How Long Does A Gas Safety Certificate Last?

As a result of faulty installation and irregular maintenance of gas appliances and chimneys, a lot of people have been met with an untimely death caused by the toxic gas - carbon monoxide. This is a gas that’s completely odourless, colourless and tasteless - meaning you can’t identify one of its in the environment. But what you should know is, if you stay in an environment filled with carbon monoxide, you’d probably be dead within a couple of hours. Consequently as a landlord, you must do what’s best to ensure the safety of all your tenants by making sure that all your gas appliances and chimneys are subjected to annual check by an approved Gas Safe engineer as required by the law.

Wondering how long a Gas Safety Check will take? The safety of your gas is guaranteed by carrying out regular examinations. Whether or not you possess a gas alarm, it’s still vital to conduct regular gas safe checks to make sure your home is safe. A typical gas safe check would last between 30 to 60 minutes for a normal domestic property. However, in the situations whereby a need for repair arises, it may take longer time to complete. Other factors that can also affect the timing includes includes both the size and location of your property.

So how long does a gas safety certificate last? The simple answer to this question is 12 months. If you own a rental property in the UK, it’s up to you to ensure all your gas appliances and chimney is check after every 12 months to obtain a Gas Safety Certificate which you should hand out a copy to all tenants living in your property. However, if you don’t own the property, you can inform your landlord to get one as soon as possible while also providing a carbon monoxide alarm.