Find a Heating Engineer you can trust in Abbey Wood.

No. You must never repair your own boiler – only a Gas Safe-registered engineer can do any work on your boiler. You can do simple DIY tasks to repressurise your boiler or stop a leak, but if you have to remove the outer casing of the boiler or touch the flue then you must get a qualified boiler engineer to take a look at your central heating system.

How To Install An Oil Boiler Heating System

Just like several other skills, the installation of an oil boiler heating system can be a challenge. It requires enough persistence to actually get right, so if you’re the type with little patience, we’d recommend you hire the services of a professional oil boiler heating system fitter who can guarantee the best results and save you time and extra money due to potential damages.

To install your boiler system yourself, it’s always advisable to start by getting the information on the best installation processes from the supplying company which will go a long way to save you from future headaches. However, we’ve put together this guide to give you a basic knowledge on how its done. Let’s have a look!

lRead Instruction Manual

• Carefully read and digest the instruction manual thoroughly.

• Make sure you understand the installation diagrams

• Spread out the materials and get familiar with them.

lFigure Out What Goes Where

• Take your time to determine where everything goes in relation to the others.

• Identify the new radiator’s position.

• Get sufficient sealants to prevent possible leakages inside the walls.

lIdentify The Pipe Routes

• Determine the pipe routes while fitting the new radiators

lInstall The Boiler

• Turn off water and all electrics

• Fit the boiler into the wall

• Make sure the fittings are secured.

lInstall The Radiator

• The effectiveness of your home’s heating system is as good as the radiators you incorporate and how good they’re installed.

• You may have to utilize extra radiators in large open plan kitchens and living rooms (for effective heating).

lOffer Ventilation

• Once you’ve successfully installed the new radiator, a small dose of air ventilation would be needed.

• Turn the key of each valve located at the bottom, do not stop until a little amount of water spills over the top of the unit.

Ad hoc visits from your engineer to fix small issues with your heating system may actually seem cheaper and a lot more affordable, however when a boiler is ripe enough for a change these small issues are always never ending. Over some period of time, these small issues will inevitably get worse and the idea of “mend and make do will be an absolutely false economy. The best course of action in this sort of event is to find a replacement boiler to install as soon as possible. In this article, we’re going to give you some hints that’ll show you when your boiler needs to be replaced. Now let’s take a look!

✓ Insufficient hot water. Here, you’ll have to check the size of your hot water cylinder. It’s crucial to make sure that your boiler is rightly sized to power your heating as well as hot water circuit in line with your demands. You should always seek the advice of a heating expert who can recommend whether to fix or replace the boiler.

✓ Strange noises. It’s normal for components of the boiler to become worn or damaged over time. Replacing the particular component that’s causing the knocking or rattling may seem cost effective at first but more often than not, the noises usually signal a bigger issue which is likely to build up over time. Hence, it’ll be a lot more logical to replace the boiler itself.

✓ Regular repair of your boiler. It’s essential to have your heating system serviced by a Gas Safe engineer on an annual basis. However, when you have to call them more often than once a year for your yearly maintenance, it may be a wise decision to consider getting a replacement.

✓ Other events whereby you may need a new boiler includes when you can’t get the right temperature in your room, when the radiators don’t heat up as they should, when your boiler leaks and if your boiler still has a pilot light.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

If you’re looking to acquire smart thermostats in your home, but wondering about its money saving qualities, then this is for you! Not only do smart thermostats add new impressive features to your home, but it can also save you both energy and money. According to many reports using a programmable thermostat can save you between the range of £130 to £150 on an annual basis. Now think about using a smart thermostat that makes it a lot more easier for you.

Wondering how smart thermostat save money? Simply set your smart thermostat one or two degrees lower or higher than the usual number. Once done, you’re likely to notice 1% to 3% reduction in your energy bills. And if you want even more, you simply increase the percentage to about 10 degrees to 15 degrees to cover the period you spend at work and watch as you save up to 10 percent of your energy bills.

Generally, a smart thermostats will save you money in two major ways. These includes:

• They Do All The Thinking For You

The smart thermostat watches your behaviour and study the time you’re at home and when you’re not as well as your preferred temperature at particular times in a day, and that’s why they are termed as “smart. they’ll automatically adjust the settings to ensure you get home to a perfect temperature.

• They Keep Tabs On Your Usage

You can always count on a two way communicating smart thermostat to watch your usage while also collecting the data and sharing it with you. It informs you of your energy usage rate as well as the estimated amount. Once you’ve been notified, you can manual adjustment or leave it to the thermostat to help manage your energy.

Installing your Nest thermostat may not be as easy as screwing a light bulb, but we can also assure you that it isn’t very difficult either. However, if you lack the needed training or experience to pull it off, we’d recommend you hire the services of a professional in order to save yourself some time and money. This guide will give you some quick and easy steps to follow and ensure you make no errors during the installation process.

Once installed removing the Nest Thermostat can be done. To get started, you’ll need just a Philips head screwdriver which Nest has thoughtfully provided with the device.

• Turn off the Nest Thermostat by switching the circuit breaker to the off position.

• Label or mark your old thermostat’s wires. However, if you notice your thermostat is tagged 120v or 240v, or possesses thick wires, do not connect the wires to the Nest as you have a high voltage system.

• Uninstall the old thermostat by locating detaching the wires coming out from the wall into the thermostat. Once done, simply unscrew the device from the wall

• Mark the spot of your thermostat. Do this by threading wires through the Nest base plate’s centre incorporate the tiny bubble level. Once done, you can then use a pencil to mark te two screw holes.

• Attach the trim plate. If you wish to cover the screw holes, simply install the trim plate in the Nest box’s bottom to the base plate.

• Using the screws and screwdriver, attach the Nest base to the wall.

• Connect the wires to the Nest by putting the labelled wires in the Nest’s corresponding ports.

• Put the Nest display by lining up the connector on the display’s back.

• Turn on the power by switching the circuit breaker to the on position

• Connect your Nest thermostat to the WiFi network.

• Follow the on-screen guide and set the temperature.

• Use your smartphone or tablet to download the Nest thermostat’s mobile app to monitor and control your device remotely.

As you would have guessed, the British Gas is one of the leading home assistant companies located in the United Kingdom which delivers a large variety of services to customers and boilers. Basically, they offer four (4) service packages. The first package is an annual boiler service and boiler as well as controls repair. Meanwhile the fourth package (also the largest) combines boiler services with central heating, plumbing, drains as well as home electrics.

Apart from the monthly payment package offerings, customers are allowed to pay on a yearly basis with a large lump sum. If you opt to pay annually, this will help you save some amount of money. There’s also the option of paying an extra £60 to further lower either monthly or annual costs. What’s more? Customers are also allowed to pay an extra of £99 to get either £2.50 for boiler repairs a month or £5.50 for both repairs on boiler and its controls as well as central heating system repairs.

After placing a claim, the repairs required by your boiler would be made within 24 hours. However, in certain cases, there may be some delays as British Gas tend to rate vulnerable customers ( such as elderly persons and families with little kids) higher than the usual ones. All products will include a 24/7 customer support, unlimited call outs as well as a 14 day cooling off period if you choose to remove any service.

In conclusion, British Gas is an affordable and hassle free company offering customers top notch services. Their gas boiler cover include so many juicy benefits you simply can’t afford to miss out on if you have a gas boiler in your home or property.

If your boiler is leaking, there are some checks that you can do yourself. However, you should never attempt to repair your boiler yourself – only a Gas Safe-registered engineer should conduct repairs.

There are 3 main reasons why your boiler might be leaking: there’s a pressure valve fault, a temperature valve leak or corrosion in the system. An engineer will be able to spot the problem quickly, but in the meantime there are a few things you can do:

Check the pipe fittings

If your boiler is leaking water around the pipe fittings, it could be an installation fault and you should get in touch with the engineer that fitted it. You can check the pipe fittings by drying the area then waiting to see if the water appears again. If it does, you may be able to do a ¼ turn of the pipe to stop it. However, you should still call the engineer that installed it to ask them to check the PTFE tape on the inside.

Inspect the seals

Over time, the rubber seals on a boiler can start to perish, so if you have an old boiler this could be the source of your leak. If you have a new boiler, it could be caused by your boiler running over pressure.

Heat exchanger corrosion

Unfortunately, if a boiler engineer discovers that the boiler is leaking water from the heat exchanger, this is the end of the road for your system. The heat exchanger is the most expensive part of your boiler, so it makes more financial sense to replace your boiler with a newer, more efficient model rather than try to replace it.