Find a Heating Engineer you can trust in Fochabers.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

• Switch off your boiler and let it cool completely

• Make sure both ends of your filling loop are attached

• Open both valves to allow cold water into the system – you’ll hear it start to move

• Look out for your pressure gauge to show 1.5 bar

• Close both valves

• Switch your boiler back on

• Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

Many domestic biomass boilers are no bigger than a standard gas boiler. However, they do require a flue, a feeder and a space to store the fuel. These can be designed to suit many different properties and will fit in lots of homes or a garage or outbuilding.

The Hive thermostat stand is relatively easy to install, however if you lack the necessary training or experience, this is a task you might want to leave to a professional to guarantee the best result while also saving you money and time. This guide will give you a good insight into the Hive thermostat installation process.

The installation of a Hive thermostat does require it to be connected to your home boiler. For this reason we always recommend you get a professional to install it. However once install the Hive Smart Thermostat is very easy to operate and move the controller around your home. To get started, you can follow these steps:

• Press the lever at the lower side of the thermostat and pull away from the front to detach the back plate of your device.

• Once done, simply hang the thermostat on the stand back plate and ensure it holds firmly in place

When it comes to Hive thermostat installation, you might also want to consider the positioning of the device in such a way to heat your home even more efficiently as its designed to be very sensitive to temperature. To identify the best spot for your Hive thermostat, let’s take a look at some of the dos and don’ts.

A Few Dos:

• Do maintain the position of your Hive Thermostat to keep a stable connection with the receive and Hive Hub.

• Do ensure that the position chosen is the centre of your home or a frequently used room.

• Do place the thermostat about 1 to 1.5 metres from floor.

• Do ensure that your thermostat is in a close proximity with the hub and receiver for a better functionality.

A Few Don’ts:

• Don’t place your Hive thermostat stand close to radiators, direct sunlight or other heat sources,

• Don’t position your device near or at places that can expoerience a sudden change in temperature such as the front or back door.

• Don’t leave your thermostat too close to curtains or ornaments.

A combination boiler, also referred to as a “combi boiler, delivers both domestic hot water and space heating in a single package so as to save space, and in a lot of cases, money. These great features makes the appliance a very popular choice in UK homes and in fact, it represents more than 50 percent of all new boilers fitted in the UK on a yearly basis.

Most modern and high efficiency combi boilers are usually stainless steel condensing boilers which normally features an in-built secondary heat exchanger to deliver domestic hot water to a home or property. What’s more? When it comes to the heating season or the cold months, the combi boiler will operated as required to heat a structure and offer hot water for showers, sinks as well as other hot water appliances around the house. And when it gets to the warm season or summer months, the combi boiler will only work when there’s a need for domestic hot water which also helps you save more money.

Combi boilers are able to provide domestic hot water in such a way that’s energy efficient due to two primary reasons - the combi units possess a very high operating efficiency and also have a low internal water volume. As a result, in during the hot summer when space heating is not required, you’ll only have to pay to heat up the hot water that you really need and not an entire tank.

Combi boilers also have the following benefits:

✓ Lower costs. Due to the combined nature of the boiler and the lack of tank in the roof space, the installation time and costs are at a minimum.

✓ Saves space in your home as it effectively combines a central heating boiler with a water heater into one unit.

The Oil Firing Technical Association or OFTEC operate a competent persons scheme to certify installers. It’s always recommended to use an installer with this certification as it proves they have the training and expertise to properly install your boiler and give you realistic advice on the efficiency of your system. Also, OFTEC registered installers offer Workmanship Warranties to protect you if there are any problems after installation.

If your boiler is making strange noises or smells, or doesn’t seem to be working properly, it may need replacing. Boilers usually last about 10-15 years. Even if your boiler is working normally, it’s worth replacing when it gets this old. An annual check will establish if there are terminal problems with a boiler that cannot be fixed.

How Can I Get My Oil Boiler Repaired?

Did your oil boiler just broke down and you’re considering your repair options? Well, you’ve come to the right place! Whenever your oil boiler breaks down, you have two options - repair it yourself or get in touch with a reliable professional. If you lack proper training or experience when it comes to fixing of oil boilers, we’d recommend that you rather hire the services of a trustworthy oil boiler engineer who can guarantee the best results while also saving you time and money that could result from possible costly errors.

However the issue is, not all oil boiler repair services are created equal. The words “expert and “professional are now so cheap that almost, if not all oil boiler repair companies online today make use of those words to qualify themselves. However, when several of them are done delivering their oil boiler repair services you’ll have no other choice than to start questioning their claimed status. In order to separate the boys from the men very early on, a little caution and some research is all that’s needed to know the most reliable company to approach.

To get a good repair company, the first step would be to make sure the company is fully accredited with a professional certification scheme so as to be sure that they’re actually qualified to deliver the service.

Another step you can take is by requesting personal recommendations from family and friends. For a company to be referred by several homeowners in the local area then it must be doing something that’s worth the money invested.

You can as well make use of the internet to get a reliable oil boiler repair company. You can start by visiting the website of the company that manufactured you appliance to identify any recommended repair companies. Go through the companies’ testimonials but do not rely too much on them because in several cases they may not be authentic.

Ad hoc visits from your engineer to fix small issues with your heating system may actually seem cheaper and a lot more affordable, however when a boiler is ripe enough for a change these small issues are always never ending. Over some period of time, these small issues will inevitably get worse and the idea of “mend and make do will be an absolutely false economy. The best course of action in this sort of event is to find a replacement boiler to install as soon as possible. In this article, we’re going to give you some hints that’ll show you when your boiler needs to be replaced. Now let’s take a look!

✓ Insufficient hot water. Here, you’ll have to check the size of your hot water cylinder. It’s crucial to make sure that your boiler is rightly sized to power your heating as well as hot water circuit in line with your demands. You should always seek the advice of a heating expert who can recommend whether to fix or replace the boiler.

✓ Strange noises. It’s normal for components of the boiler to become worn or damaged over time. Replacing the particular component that’s causing the knocking or rattling may seem cost effective at first but more often than not, the noises usually signal a bigger issue which is likely to build up over time. Hence, it’ll be a lot more logical to replace the boiler itself.

✓ Regular repair of your boiler. It’s essential to have your heating system serviced by a Gas Safe engineer on an annual basis. However, when you have to call them more often than once a year for your yearly maintenance, it may be a wise decision to consider getting a replacement.

✓ Other events whereby you may need a new boiler includes when you can’t get the right temperature in your room, when the radiators don’t heat up as they should, when your boiler leaks and if your boiler still has a pilot light.