Find a Heating Engineer you can trust in Attleborough.

Many domestic biomass boilers are no bigger than a standard gas boiler. However, they do require a flue, a feeder and a space to store the fuel. These can be designed to suit many different properties and will fit in lots of homes or a garage or outbuilding.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

As you would have guessed, the British Gas is one of the leading home assistant companies located in the United Kingdom which delivers a large variety of services to customers and boilers. Basically, they offer four (4) service packages. The first package is an annual boiler service and boiler as well as controls repair. Meanwhile the fourth package (also the largest) combines boiler services with central heating, plumbing, drains as well as home electrics.

Apart from the monthly payment package offerings, customers are allowed to pay on a yearly basis with a large lump sum. If you opt to pay annually, this will help you save some amount of money. There’s also the option of paying an extra £60 to further lower either monthly or annual costs. What’s more? Customers are also allowed to pay an extra of £99 to get either £2.50 for boiler repairs a month or £5.50 for both repairs on boiler and its controls as well as central heating system repairs.

After placing a claim, the repairs required by your boiler would be made within 24 hours. However, in certain cases, there may be some delays as British Gas tend to rate vulnerable customers ( such as elderly persons and families with little kids) higher than the usual ones. All products will include a 24/7 customer support, unlimited call outs as well as a 14 day cooling off period if you choose to remove any service.

In conclusion, British Gas is an affordable and hassle free company offering customers top notch services. Their gas boiler cover include so many juicy benefits you simply can’t afford to miss out on if you have a gas boiler in your home or property.

If you choose to install an LPG boiler, you’ll need to find an LPG supplier. They’ll deliver fuel to you every time your storage tank runs low. You can even rent a storage tank from them if you don’t want to buy one. Make sure you know who your local suppliers are and where they are based.

How To Install An Oil Boiler Heating System

Just like several other skills, the installation of an oil boiler heating system can be a challenge. It requires enough persistence to actually get right, so if you’re the type with little patience, we’d recommend you hire the services of a professional oil boiler heating system fitter who can guarantee the best results and save you time and extra money due to potential damages.

To install your boiler system yourself, it’s always advisable to start by getting the information on the best installation processes from the supplying company which will go a long way to save you from future headaches. However, we’ve put together this guide to give you a basic knowledge on how its done. Let’s have a look!

lRead Instruction Manual

• Carefully read and digest the instruction manual thoroughly.

• Make sure you understand the installation diagrams

• Spread out the materials and get familiar with them.

lFigure Out What Goes Where

• Take your time to determine where everything goes in relation to the others.

• Identify the new radiator’s position.

• Get sufficient sealants to prevent possible leakages inside the walls.

lIdentify The Pipe Routes

• Determine the pipe routes while fitting the new radiators

lInstall The Boiler

• Turn off water and all electrics

• Fit the boiler into the wall

• Make sure the fittings are secured.

lInstall The Radiator

• The effectiveness of your home’s heating system is as good as the radiators you incorporate and how good they’re installed.

• You may have to utilize extra radiators in large open plan kitchens and living rooms (for effective heating).

lOffer Ventilation

• Once you’ve successfully installed the new radiator, a small dose of air ventilation would be needed.

• Turn the key of each valve located at the bottom, do not stop until a little amount of water spills over the top of the unit.

When your boiler is being replaced you won’t have hot water or central heating. If you don’t mind this you can stay in your home, and use portable electric heaters if needed. Most installers undertake a power flush before installing a new boiler now and this can cause muck and debris from the pipework, so you may wish to get out of the way while this is happening!

Can You Replace A Gas Boiler With An Electric Boiler?

In the UK, there are about 22 million households that are heated with the use of a gas boiler. However, do not assume that they’re the best type of boiler to install. The fact is, if your house isn’t connected to the main gas supply, the best option is for you to install an electric boiler rather than a gas boiler. So is it possible to replace a gas boiler with an electric boiler? The simple answer is yes. Both heating system options work in varying ways and also with a different impact on the environment.

The gas boiler is able to generate heat with the help of a gas burner. A heat exchanger is linked to the burner and heats the water available in its chamber. The hot water is then supplied to the heating circuit.

However, the thing is that natural gas can actually be more affordable when compared to using electricity to operate your boiler, but they have a negative impact on the environment. This is because gas boilers make use of an odourless, colourless and poisonous gas - carbon monoxide.

Meanwhile electric boilers are powered by electrical energy, hence, no carbon monoxide leak risks. Instead of using gas to heat up water, electric boilers distribute energy to heating elements which, in turn, heats up the water. So thinking about what’s best for the environment, you’d go for electric boilers. However, they’re more costly and are not as efficient as oil boilers.

If you reside in a smaller house that’s not connected to the main gas supply, then you might want to consider installing an electric boiler. However, if you live in a larger house, an electric boiler may not be the best option as they’re mostly designed to generate little quantity of hot water.

To ensure that your boiler is safe and operating efficiently, it’s essential to have it serviced on a regular basis.

Generally, a boiler service will deliver a wide array of benefits which includes the opportunity to identify safety issues like a possible leak of carbon monoxide, efficient use of energy and reduction in energy bills, prevention of breakdowns, a valid warranty when the boiler is serviced regularly by a qualified engineer as well as an extended lifespan. So what exactly does a boiler service cover? This guide will give you a good insight as to what happens during that service.

Before we get started, it’s very important to note that the work done is always as good as the engineer you employ. Therefore, it’s advisable to make sure your preferred engineer is qualified before proceeding with the service. Below are some of the basic practices the engineer may perform during their visit.

• Thorough Inspection

During the visit, the engineer will carry out a detailed examination of your boiler to ensure it still meets the current standards while also making sure that there are no leaks or corrosion. What’s more? They’ll also examine the boiler’s flame for any faults.

• Boiler Casing Removal

The boiler casing will be detached to check all components and ensure they’re free from all forms of dirt and see to it that they’re all working just as they should. This will include examination of the heat exchanger, main injector, burner and spark probe.

• Flue Examination

The engineer will inspect the flue terminals to make sure there are no form of obstructions and it’s also safely installed.

• Gas Pressure Examination

This is done to make sure the heating system is operating at the right pressure.