Find a Heating Engineer you can trust in Billingham.

Your LPG storage tank will need to go outside your property, possibly underground if you have limited space. There are planning rules that restrict where you can put your tank, especially if your property is listed or on designated land. Take a look at our planning permission article to find out more.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

Breakdowns of boilers are quite common during the winter months and are usually very expensive to repair when this occurs. According to the research carried out recently by uSwitch, repairing a boiler can cost an average of about £314 with a figure over 20 percent of homes experiencing various heating system issues last year.

To answer the question of whether or not your existing home insurance will be enough to cover the boiler breakdown, the answer is probably not. This is due to the fact that heating system faults or breakdowns is a very common occurrence and as a result of poor maintenance practices as well as a high repair cost, several insurance companies often remove it from their home insurance policies.

Generally, you’d be given an option of what is termed as “emergency home cover which is an add on or extra to your home insurance policy. Luckily, this add on is quite inexpensive and may be as little as £4 or £5 per month. Depending on your need or budget, you can also purchase the add on as a “stand alone from your current insurer or another company. However, the stand alone option is usually more expensive.

The emergency home cover normally provides coverage for the boiler repair cost and few times, the rest of the central heating system as well. Being fully aware how important a boiler can be, insurance companies usually deliver a rapid response service as suggested in the name, “emergency home cover. However, the maximum pay out for call out charges is capped at a particular amount which usually ranges from £500 and £1,000. Apart from the call out fees, the emergency cover also includes a limit on the pay out amount for future required repairs of heating systems which includes both parts labour.

Biomass boilers will work with existing central heating systems, presuming this is not decades old, whether they use radiators or under floor heating. A surveyor will check the existing system you have in place before quoting for or recommending a biomass boiler to you.

When it comes to gas boilers, this is one of the most frequent questions that always pops up and for a good reason. When you invest a considerable amount of money to acquire and install a gas boiler in your home or property, it’s only reasonable not only to expect the boiler to warm up your home efficiently, but also to do so for a long period of time. If you’ve just bought or about to get a new gas boiler, it’s likely you won’t have to worry about getting a replacement for a lengthy period of time. Several gas boilers will last for anywhere between 10 to 15 years on the average. However in the event whereby you have an existing one that’s fast approaching the end of it’s useful life, then you should know the time go get a new gas boiler is just around the corner, and the earlier you make the purchase, the better (to avoid any surprise breakdowns that’ll leave your home super uncomfortable).

Just like any other home appliance, it’s a fact that an older gas boiler ( especially those that have been installed over a decade ago) are significantly less efficient that the new modern ones. When the older versions were manufactured is a completely different time to now as both technology and climate concerns are wide apart. So when your existing boiler is approaching the end of it’s useful life, it’ll be wise to start saving up to cover the cost of getting a new one. However, if it’s only about 5 years ago your boiler was installed, it’s highly likely to still be very efficient.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

1. Switch off your boiler and let it cool completely
2. Make sure both ends of your filling loop are attached
3. Open both valves to allow cold water into the system – you’ll hear it start to move
4. Look out for your pressure gauge to show 1.5 bar
5. Close both valves
6. Switch your boiler back on
7. Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

Does Home Insurance Cover Boiler Repairs?

When winter comes, your boiler is most likely to be one of the most used appliances in your home. It keeps operating for several hours to ensure your house remains warm and conducive and then during those cold evenings, it supplies the much needed hot water to guarantee a restive night. But with so much usage and many moving parts, you’d naturally expect your boiler to breakdown at some point especially if it’s 7 years old or above. So what’s the next line of action when it happens, leaving your radiators off and water cold? With the likely high boiler repair cost, it’s only logical to consider whether your boiler repairs is covered by your home insurance.

In almost all situations, the standard home insurance will not provide coverage for the cost of repairing or replacing a broken boiler. Being fully aware that boiler breakdowns are mostly caused by a lack or not so regular maintenance practices or servicing, most home insurance providers will exclude it from this from their offerings. In fact, a home insurance is more likely to provide coverage for the damage that has happened as a result of a broken appliance. For instance, the damage caused as a result of gas, oil or water leaking from a boiler are more likely to be paid for by the home insurance providers, but they’ll not pay for the repair or replacement of the broken boiler itself.

If you need our home insurance to cover your boiler repair, then you might just be able to get an extra insurance cover from your provider that includes a broken boiler repair. You can consult them to determine if this is possible as well as the cost to be paid per month. This will normally cost about £5 to £10 per month, but it gives you a peace of mind knowing you’re covered if your boiler happens to breakdown.

Do British Gas Service Oil Boilers?

Are you interested in finding out whether or not the British Gas service oil boilers? Well, you’ll find the answer in this article! The British Gas engineers are able to repair several types of boilers such as home based combi, conventional as well as system boilers. Unfortunately, they do not fix oil boilers, electric boilers or solid fuel boilers, but if you possess a gas boiler that’s more than 70kW which is mostly present in commercial premises or large buildings you can give them a call.

For a yearly boiler service British Gas engineers will provide the following solutions to ensure central heating and boiler are both in proper working condition and also absolutely safe.

• Inspection of your boiler for possible leaks and corrosion.

• Detach your boiler casing to ascertain the proper functioning of it’s main components.

• Clean up all parts as necessary

• Attach the casing back to the system and make sure its well sealed

• Inspect the level of the gas pressure to ensure that it’s at the right level.

• Perform a flue check to determine that the are no toxic gas emissions like carbon monoxide being discharged by your heating system.

Upon completion of the annual boiler service, the British Gas qualified engineers will then drop a checklist with you which is going to include all the relevant information you may want to know about your boiler system.

In some cases, British Gas engineers may be able to complete the entire boiler service in one visit. However, it all depends on the problem that’s discovered (if any). They may not possess the required part to fix the problem with them, so they’ll have to order it from the British Gas national distribution centre. Most times, this part will get to them the next day so they can finish their tasks as soon as possible.