Find a Heating Engineer you can trust in Northallerton.

If your boiler is leaking, there are some checks that you can do yourself. However, you should never attempt to repair your boiler yourself – only a Gas Safe-registered engineer should conduct repairs.

There are 3 main reasons why your boiler might be leaking: there’s a pressure valve fault, a temperature valve leak or corrosion in the system. An engineer will be able to spot the problem quickly, but in the meantime there are a few things you can do:

Check the pipe fittings

If your boiler is leaking water around the pipe fittings, it could be an installation fault and you should get in touch with the engineer that fitted it. You can check the pipe fittings by drying the area then waiting to see if the water appears again. If it does, you may be able to do a ¼ turn of the pipe to stop it. However, you should still call the engineer that installed it to ask them to check the PTFE tape on the inside.

Inspect the seals

Over time, the rubber seals on a boiler can start to perish, so if you have an old boiler this could be the source of your leak. If you have a new boiler, it could be caused by your boiler running over pressure.

Heat exchanger corrosion

Unfortunately, if a boiler engineer discovers that the boiler is leaking water from the heat exchanger, this is the end of the road for your system. The heat exchanger is the most expensive part of your boiler, so it makes more financial sense to replace your boiler with a newer, more efficient model rather than try to replace it.

No. You must never repair your own boiler – only a Gas Safe-registered engineer can do any work on your boiler. You can do simple DIY tasks to repressurise your boiler or stop a leak, but if you have to remove the outer casing of the boiler or touch the flue then you must get a qualified boiler engineer to take a look at your central heating system.

How Much Is A Boiler Service?

A broken boiler can be a huge pain and even more so if it occurs during the winter months. A cold house and cold shower is not a situation to be handled with levity especially when there are older people or more vulnerable members in the house. To ensure your boiler keeps functioning the way it should for a lengthy period of time, it’s crucial to ensure that you have your boiler serviced on a yearly basis. But while the summer or warmer months happen to be the most cost effective time to have the boiler servicing done, doing it during the depths of winter can go a long way to ensure that you and your loved ones get through the cold without any unwanted occurrence or boiler issues.

Generally, to have your boiler serviced will cost anything within the range of £80 to about £120, but at times, this can even be more depending on a plethora of factors. The servicing cost will be based on the particular company you choose, the type of boiler you possess, as well as your location in the UK. For instance, if you happen to live in London where demands are higher than the other regions, then you’ll most likely have to pay more money to have your boiler serviced than other homeowners facing similar issues but staying in the other lower demand regions.

Asides from hiring a professional to service your boiler on an annual basis, you should also try to help maintain its efficiency and health in between those services. This will not be a substitute to the regular servicing or even make the servicing a lot simpler, but will surely help keep it at a maximum efficiency while also keeping the cost of your heating bills down.

During a boiler service, your boiler engineer will perform a series of checks to ensure that your boiler is safe and efficient. First, they will conduct a visual inspection to check for any corrosion or leaks. They will also check the flame in your boiler. They’ll then remove the boiler casing and check all the components, including the heat exchanger, burner and spark probe, then clean the inside. After this, they’ll check the flue for obstructions and ensure that it’s safely fitted. They will then do a gas pressure check to ensure the boiler is working at the right pressure, before firing it up to check for any working faults.

How To Fix A Broken Boiler

To fix any problem when it comes to home appliances, the first step is always to identify the problem while also carrying out thorough checks - a broken boiler is not an exception. Putting enough time and effort in diagnosing a problem can go a lot way to save you both time and money. So here are some of the steps you can take to fix your broken boiler before you put a call out to a licensed engineer.

✓ Check to confirm if your pilot light is on. Whenever you’re facing some issues with your boiler, this should always be the first thing you do. The pilot light being on speak volumes, if the light is off then there’s absolutely no way the flame can start the appliance’s gas supply. You should try to put it back on, if off. To do this, you simply have to follow the detailed instructions on your boiler’s manual strictly. If after following these actions to the letter and the issue remains the same, then you’d probably need the services of an a qualified engineer. Never try to fix the issue on your own.

✓ Check the pressure. The solution to the headaches might sometimes be as simple as examining your appliance’s pressure gauge. Here, the good numbers are around 1.0 or1.5, if it happens to fall below this, then you should open the boiler’s instruction manual. You can also inspect your radiator valves for any leaks. You’d have to call in a specialist to solve the issue.

✓ Check the thermostat. Here, it’s important to note that a faulty thermostat doesn’t necessarily imply a broken boiler. It may just signify that you need to replace your thermostat. Simply check to ensure that your thermostat is turned on and temperature is at the appropriate degree.

Yes. Modern condensing oil boilers are ‘A’ rated and therefore as efficient as comparable gas boilers. They come with the same controls as gas central heating systems, so you can still use a thermostat to control your heating efficiently. Also, oil is more efficient as a fuel source than gas, so you will get more energy per unit of oil. Oil prices can fluctuate, however, so ensure that you find a good supplier.

The short answer to this is no! Smart thermostats can still be used without WiFi, however, they’ll be deprived of some certain capabilities and innovative features that comes mainly due to their ability to connect to the internet. As a result, the smart thermostat will only be functional for basic task such as heating and cooling control. In other words, making use of a WiFi connection will be in your best bet to enjoy the multiple juicy benefits that comes with a smart thermostats such as remote monitoring, ability to connect to other devices and display local weather conditions and much more. And what’s the use of purchasing a smart thermostat if you’d not be able to enjoy these remarkable features?

However, even when you have a WiFi, it’s expected for the connection to fail at times. When this happens, what will be the impact on your smart thermostat? Let’s have a closer look!

• As you would have expected, when your smart thermostat is disconnected from WiFi, features that are controlled with the mobile app would all be impacted. And this might be a big headache when you wish to access these features and control remotely when far away from home.

• When your smart thermostat connection to WiFi fails, all live updates and alerts would be affected. This implies that you’d stop seeing updates, reports and notifications on your mobile device. As a result, you’ll not be notified in case of an emergency like electricity cut-outs, water leaks, humidity and temperatures exceeding the set levels as well as thermostat’s low battery.

• The lack of a WiFi connection might have taken away all the juicy advantages of having a smart thermostat, but one function that remains unaffected is the basic one - the control of your home’s heating and cooling system. In other words, if your smart thermostat is offline, your home will still be heated and cooled to the thermostat’s set temperature.

If you’re building a connected home, a smart thermostat allows you to change the temperature in your home. And not only do several smart thermostats come with touch screens and a user friendly interface, but they’re also compatible with Amazon Alexa, Google Assistant and other voice controlled personal assistants. So how does a smart thermostat work? Let’s have a look!

Generally, smart thermostats are connected to the home’s Heating and/or Air Con system via C wire (common wire). Homes that lacks a C wire (especially older homes) will have to install one first before getting a smart thermostat. The C wire is a crucial element in the installation process as it works mainly to wire your smart thermostats into the Boiler system without tampering with the wiring for the other appliances in the house.

The smart thermostats comes with some special temperature setting which you can access by connecting them to your home’s WiFi. These include:

• Mobile Control

Most smart thermostats are specially designed to enable users to control the temperature of their home from the comfort of their couch or car via their unique mobile apps. This feature is just perfect if you particularly like getting the perfect temperature in your home without having to get out of bed.

• Humidity Controls

Although, the humidity of your home can not really be adjusted with a smart thermostat but you can always stay on top of it by monitoring it or setting an alarm on your phone to go off when the humidity changes.

• Geofencing Feature

With a smart thermostat, you can choose the particular times of the day you want it in action. This feature enables you to go on impromptu travels without having to worry about your energy bills - some smart thermostats come with the geotracking feature which determines when you’ve left the house and adjusts the temperature of the home accordingly with your energy usage in mind.