Find a Landscaper you can trust in Alva.

• Paving slabs – old or cheap ones are fine
• Timber for the frame and legs
• Type 1 MOT hardcore

1. Mark out the area as we explain in ‘How to lay decking’. Then, dig to 200mm below where you want to surface of the decking to be.
2. Add a 50mm layer of hardcore and make sure it’s compact.
3. Build the decking sub-frame as we describe in ‘How to build a deck frame’.
4. Lay out paving slabs along the edges and in the centre of the area. This will help to spread the weight of the decking.
5. Set the decking frame on the slabs, checking for high or low points and adding off-cuts of timber where needed. Don’t forget to sand and seal these off-cuts with decking preservative.
6. Add your joists and then the deck boards, leaving the recommended gaps of expansion of between 5-8mm.

The cheapest fence to install is, generally, a pressure-treated pine wooden fence at around £20 per linear foot. This includes the materials and labour costs. Wire fencing is technically cheaper at around £5 per foot, but it’s not a great material to use in homes as it looks unsightly and doesn’t provide any privacy.

Pitting, also referred to as spalling is the event whereby “pits” or small holes start showing on the surface of your concrete driveway which makes it appear both worn and uneven. Concrete driveway pitting is a common but highly frustrating problem for most homeowners. You’ll see some concrete driveways that’ll only start to pit after a couple of years, but this is not true for all concrete driveways as others will start to show signs only after a couple of months. So how do you tackle this issue? Well, it’s relatively simple to tackle, however if you’re not confident or lack the necessary skills, we’d recommend you get in touch with a reliable professional who can guarantee the best results for help. In this guide, we’ll take you through the concrete driveway pitting repair process.

✓ Prepare the pits by cleaning the area, clearing out all debris and more. The small pits can be cleaned with a stiff brush while a sturdy broom will do a good job for larger pits.

✓ Make use of a hose to spray the concrete pits and flush out all remaining bits of waste.

✓ If you’re tackling series of small pits, simply use a caulking gun filled with pre-mixed epoxy and specially formulated for concrete to fill the pits. Clear off the excess eproxy ensuring that its level with the concrete surface. Once done, simply leave for at least 24 hours before the application of a concrete sealant to prevent the wear and tear of the new concrete.

✓ Chisel out a little concrete and clean with a pressure washer. Once done, apply a concrete resurfacing compound mixture into the holes and use a trowel to level off.

✓ Ensure that the repaired concrete driveway is protected from rain and foot traffic for at least 6 hours (or 24 hours for vehicles).

Different types of gardening work will need to be carried out at different times of the year. Garden maintenance is a year round job, although the amount of work will usually decrease during the winter. For larger landscaping projects, aim to have these done through autumn, winter and early spring, to give plants time to get established before summer. Be aware that poor weather over winter can slow down the work.

There are a number of reasons why disputes can arise between neighbours – all of which can be quite frustrating and challenging. In some cases, this can even cause serious friction and lead to an all-out war. When it comes to the topic of fencing, one of the most common questions that arises is whether or not you can attach something to your neighbour’s fence. If you’re having the same concern, then you’ve come to the right place. In this post, we’re going to give you a good insight into this to help you make informed decisions moving forward. Let’s take a look!

The short and simple answer to this question is no, you can’t attach anything to your neighbour’s fence. If your neighbour owns the fence and you’ve not obtained any permission to do so, then you’re not allowed to attach anything to the fence. Otherwise, you can get into serious trouble with your neighbour as well as the law. If you want to attach something or have the wall on your side painted using another colour, then there’s the need to get a permission from the owner. And while doing so, make sure you’re provided with a written permission so as to avoid problems later in the future.

Another question that mostly arises is what if your neighbour declines your request, is there anything you can do about it? Well, the answer to this is no, there’s nothing you can do about it unless you’re able to convince your neighbour otherwise. And you should know starting a neighbour war or being spiteful can only make matters worse for you.

Whether you’re starting a garden from scratch or adding plants to a garden that needs a big of work, the biggest step in planting a garden is preparation. We’ll give you a few tips on how to plant a garden whatever your garden’s size. Check your soil The most important thing to do before you start to plant a garden is check your soil type. Different plants suit different soils, so you should choose ones that will like the soil in your garden. If your soil is sticky and muddy, it’s referred to as clay soil, but if it runs through your fingers when you pick it up it’s known as sandy. Ideally, you want something between the two to help your plants’ roots spread easily. If you have heavy clay soil, you’ll need to add well-rotted manure or compost to improve the structure, but if it’s sandy you’ll need to add organic matter to improve its fertility. Make a plan Don’t just start planting wherever – make sure you’ve got a plan of where you want everything to go. Do a simple drawing or cut out photos from magazines or the internet. How to plant bare root plants and trees When you’re planning what to plant in your garden, make sure you choose the correct amount and size of trees you’re going to plant. In a small to medium garden you only want one or two trees, and you don’t want anything too large that might spread too far. When you’re ready to plant, make sure there’s enough room for the roots to spread. Look for the soil ‘tide mark’ near the base which will show the depth that it was planted before, and use that as your guide. Dig your hole to the correct depth and width and fork the sides so it’s easier for roots to get in. Add some well-rotted manure and place the plant in the hole so the roots are spread out and fill the hole with soil. Planting potted plants Dig a hole deep enough for your plant – put the pot in the hole to check whether you’re there yet. You want around 2cm around the outside and don’t make the hole any deeper than the pot. If your plant has a tight root ball from outgrowing its pot, gently tease out the roots – it won’t harm the plant. How to plant plug plants in your garden Plug plants are usually mail-order plants that you get in spring and are a great way to start planting a garden. You must handle them carefully and water them before planting. Fill a small pot with compost and make a well in the centre, then drop the plug in. Gently pat the soil around it. You might need to pot them again to the next size up later on, and harden them off outside before planting them in the ground after there’s no risk of frost. With these few tips you can easily get started with planting your garden. But if you need some help and advice, get in touch with local gardeners who will be happy to give you a quote.

How To Repair Sunken Concrete Driveway

If you have concrete driveway that’s cracked, uneven and mostly especially sunken, you’d know how distasteful it can be just viewing it on your property. A sunken concrete driveway is most likely caused by rainwater erosion removing the soil under it or a big root under it which as rotted over time. Another possible cause of the sunken concrete is an improperly prepared base which implies that the soil beneath wasn’t fully compact when the concrete was poured on it. Later on the soil beneath will eventually settle and shift below the concrete driveway which weakens the integrity of the entire driveway, making it more vulnerable to cracks, unevenness and sunken.

Two ways in which you can fix this problem includes either demolishing the whole driveway, re-compact the soil underneath and fill with new concrete or repair the entire driveway using an easy process called slabjacking. In this article, we’re going to look at the slabjacking repair process as it’s significantly less expensive than the demolishing approach and will also cause minimal disruption to your lifestyle.

Also referred to as mudjacking or concrete lifting, slabjacking is simply a process used to float your existing concrete back to its original position. If you are not a competent DIYer or lack confidence to pull this off, we’d recommend reach out to a professional for help. If otherwise, then you can practice the slabjacking process given below.

✓ Drill holes through the slab.

✓ Pump grout mixture through the holes. This mixture will spread out beneath he driveway and raise it up.

✓ Lastly, fill the holes and level the concrete driveway surface.in such a way to hide the signs of the repair made.

This is a process that works to efficiently get your driveway back in a top condition relatively quickly.

With summer comes a lot of lawn challenges - from sod webworms, chinch bugs, nutsedge to drought stress, diseases and lots more. A lot of people find it hard to tell what’s happening to their lawn and probably assume it to be as a result of the summer stress and will definitely turn green again once the fall rolls in. This may be right in certain situations, but if you have fungi eating deep into your lawn, the green may not return. So, how exactly do you figure out if your lawn has diseases or pests? In this post, we’re going to provide you with a good insight into this to help you take the necessary treatment steps as soon as possible.

• Fungal structures. Fungi structures are not usually the easiest to spot as they vary in shape, colour and appearance. Fortunately, most fungi that appears on lawns will possess some type of structure which can be spotted when moisture is present. Once the night time dew sets in, you’ll be able to identify these strange growths in your lawn.
• Matted or Collapsed Areas. There is some sort of diseases that will make grass plant to wilt in little time. This, combined with fungi structures will make the grass look to have been matted in some areas.
• Discoloured or oily areas. Some areas are likely to show symptoms more than the others. While the unaffected turf may remain in its normal state, areas that are nearby may vary in colour due to the damage to the leaf tissue.
• Lesions or spots on leaves. Do you notice a certain damage pattern on the leaf blades of the grass plants? If yes, then your lawn is probably infected with a disease. Some of these spots may vary in size and colour.