Find a Landscaper you can trust in Kirkcudbright.

Laying a lawn is a task that’s best left to the professionals especially if you don’t know what you’re doing. However, if you can follow a simple logical process, you’ll save yourself a lot of headache – simply start from the edge and work inwards. If you’re looking to lay your lawn by yourself, then you’ve come to the right place! In this post, we’re going to consider the processes involved in lawn installation in order to ensure your project turns out a success. Let’s take a look!

Firstly, the tools you’re going to need to lay your lawn includes the following – sturdy boots, gardening gloves (should be thick), wheel barrow, garden fork or rotovator, landscaping rake, laying boards, knife or edge trimmer, hosepipe and broom.

1. Start from the outside edge. Install the initial strips horizontally overlapping the boundary a bit (trim the back once done). Press down carefully to make sure there’s a good contact with the soil (make sure not to squash the lawn).
2. Proceed to lay the adjacent pieces till the first row of the lawn along the entire edge is completed.
3. Continue with the next row. If there’s a need to stand on the laid turf, simply make use of a plank so as to avoid squashing or denting the turf. It’s important to ensure the successive rows are staggered to prevent the short edges from lining up.
4. Proceed by butting and pushing the edges to create a tight joint (make sure the turf is not stretched).
5. Use a wood saw or sharp serrated knife to trim any untidy edges. Remember to make use of a plank to ensure you do not walk directly on the turf.
6. Water the newly installed turf adequately to ensure the water penetrates the soil. However, do not turn it into a mud bath.

This will depend on the size of the garden and the amount of plants within it. For small gardens, fortnightly or monthly visits by a professional gardener will generally be sufficient. For larger gardens or gardens with a lot of plants, weekly visits are best. Some larger projects such as hedge cutting or tree felling may need additional one off visits.

• Tongue and groove timber boards
• Boards for the ledges and braces, at least 20mm thick
• Nails
• Hammer
• Saws, including a circular saw
• Chisel
• Mallet

1. Cut your boards to size If you can’t buy boards at the right height and width for your door, cut the boards to length using a circular saw. Don’t forget to sand and treat any cut ends with timber preservative. Lay out the boards in the best arrangement for your shed door, with the inside of the door facing up.
2. Arrange the ledges and braces On most shed doors, you’ll probably need 3 boards across the back of the door to form the ledges. The ledges keep the door straight and keep the boards of the door together. The braces are the parts of the door that slope down to form a ‘Z’ shape between the ledges. Ensure that the braces are sloped up from the bottom and middle hinge to stop the door from sagging as the timber expands and contracts in the weather. Once you’re happy with the arrangement, mark the spots on the boards where they will meet and cut out of the housings using a chisel and mallet.
3. Put the door together Use clamps to pull the boards together and hold the ledges and braces in place. Nail from the front of the door through the boards and ledges to fix them. Secure the ledges and braces with screws; you may want to pre-drill and countersink holes to prevent the wood from splitting. Remember to treat them with preservative if you do.
4. Fix the shed door hinges Make sure you measure carefully before attaching the hinges, ensuring you know where the pin sits in relation to where the door opens.
5. Treat the door and add locks and handles Apply some wood oil, like linseed or teak oil, to help prevent water damage. Then add locks or handles to your shed to help keep it secure.
If you’d rather leave it to the professionals, there are plenty of specialists that will be able to make a shed door for you, or even put up an entire shed.

Usually, slipperiness is caused by algae or dirt on top of the deck or terrace. A full cleaning treatment should restore the natural grip of the wood or stone. If slipperiness is a persistent problem, consider installing grip mats in high traffic areas of the deck.

• Have a step tread width of 900mm – if you don’t want them that wide, they should be no less than 760mm
• Add a central step riser to stairs wider than 900mm to prevent them buckling
• Add a step depth (the vertical distance between each step) of between 150 and 180mm if building your own riser, so the steps are at a comfortable depth

• Step treads (the actual step themselves)
• Step risers
• Coach screws
• Deck screws
• Saw
• Drill

1. Make sure the ground where you want to put your steps is level and firm. If it’s not, consider laying concrete or paving slabs to provide a secure surface for your steps to sit so they don’t sink.
2. Grab some joist off-cuts and cut them to the same width as your step treads. Attach them to the step risers at the top and bottom using countersunk coach screws.
3. Place the steps against the sub-frame of the deck; if you’ve put slabs down for support, make sure the steps sit in the middle of them. The longest edge of the stair riser should be on the slabs, and the short edge against the deck. Drill pilot holes through the step and sub-frame joist, then screw the step to the sub-frame with more coach screws.
4. After drilling pilot holes, screw the treads into the risers at each end with deck screws.
5. If you don’t want gaps between each stair, you can add joist off-cuts or deck boards. Measure the height and depth of the gap, then screw the off-cut or board into the step riser with two screws at each end.

1. Remove fascias and trims Unscrew or prise off the screws and nails fixing the trims and fascias to your shed.
2. Take off doors and remove windows Unscrew hinges from doors and take them off. Remove all metalwork once the door is off. If you’ve got frames on your windows, unscrew these, and remove the panes. Be extra careful if your windows are made of glass.
3. Take off the roof Prise off the tacks from the roofing felt and take the felt off – you can’t reuse it, so you’ll need to throw it away. Unscrew the screws on the roof boards and slide them off the shed’s frame – you might need a friend to help you do this.
4. Take out the roof brace (optional) If your roof has a brace, unscrew the brackets that hold it to the side of the shed. Remember not to lean on anything once you’ve taken the brace off as the walls might be wobbly.
5. Unscrew the frame from the floor Remove all the screws that are holding the shed to the base, remembering not to lean on the walls.
6. Unscrew the frame corners Starting at the corner of the front gable, remove the screws where the panels meet. Once a panel is free, lift it carefully out of the way so you can carry on with the others.