Find a Landscaper you can trust in Tywyn.

Properly erected fences shouldn’t require a great deal of maintenance. Any rotting boards can usually be replaced without replacing the whole panel. Timber fencing should be stained every 2-3 years. General maintenance is something you can carry out yourself, however, larger works may need a qualified professional to come in.

The best way to build a fence depends on what style it is, as different types have different components. However, fencing made up of posts and panels is pretty common. To put this up, you’ll need to start by measuring out and digging holes for your fence posts. Then you’ll need to fit the panels between them and use concrete to secure the posts in the ground.

There is a variety of methods available to ensure that your paving drains properly, for example draining into a lawn or soakaway. Correct drainage of paving is a requirement for planning permission. See our guide on planning permission for paving for more information.

Garden slabs are a joy to behold but only when done the right way. Well, the installation of paving slabs shouldn’t be exceed digging a little here and there, buying a small amount of mortar and pressing down the garden slab, right? Absolutely not! But we must admit how great it would have been if only it were that easy in real life. Let’s be honest, in reality, laying garden slabs does not only require you to prepare your sub-base painstakingly and mix your mortar using the appropriate materials, but you’d also have to work with accurate and precise paver placements to guarantee the patio’s longevity. Consequently, this happens to be a stressful and quite tricky challenge. If you lack the required confidence to pull this off, we’d recommend you hire the services of a seasoned professional who can guarantee the best results and also save you time and extra cash that may result from possible costly errors. In this guide, you’d gain more insight into the garden slabs laying process.

To get started, you’ll need sharp sand, cement, shovel, wheelbarrow, pointing trowel, rubber mallet, spirit level, jointing compound, hard-bristled brush and tarpaulin.

1. Mix a layer of mortar for each paver.
2. Apply the mixed mortar onto the sub base by using the trowel.
3. Slot the first flag in place and ensure not to stain the paver’s surface with the mixed mortar.
4. Using a rubber mallet, carefully tap the paver to the mortar bed. Once done, ensure the surface is even with a spirit level.
5. Take a measurement of the gap between the pavers
6. Repeat the above steps until all pavers have been perfectly laid
7. Leave the pavers to dry for about 1 to 2 days. You can protect it using a tarpaulin if concerned about rain.
8. Use the jointing compound to fill up the paver gaps to bind together the pavers. Ensure to wipe off any excess compound using the hard-bristled brush.

Laying artificial grass on concrete needs a slightly different approach to if you’re installing it over soil. The good news is that it’s much less labour intensive, as you don’t need to do any digging or levelling.

Ideally, your concrete base should be in good condition, and have an adequate fall on it to provide efficient drainage. If it doesn’t, you might have to do some repair work or drill some drainage holes first.

When you’re ready to start, begin by cleaning your concrete base. Use a jet wash or a hose and brush to dislodge and disperse any dirt or plant growth. Once it’s clean, leave it to dry completely.

Then, you need to fit an underlay - usually it’s made of foam. This will provide padding to make your artificial grass softer and more comfortable to walk on. It will also help to level out any slopes on uneven parts on the concrete. Make sure it’s a good-quality underlay that’s permeable – if it’s not, you could end up with damp artificial grass and nasty smells as it will hold moisture. Roll out the underlay and cut it to shape, taping any separate sections together.

Next, use an adhesive to secure the underlay to your concrete. Make sure you leave gaps in the adhesive to allow water to drain off easily. Leave the glue to dry, then you can start laying your grass.

Roll out your grass like you did with your underlay, cutting it to shape and joining any separate sections together with artificial grass tape. Then glue the grass to the underlay. Leave it dry, give the grass a brush, and it’ll be ready to use!

1. Start in one corner of the sub-frame and position the first board across the inner joists. You want the deck board in the opposite direction to the inner joists, ensuring that it’s flush with the frame. Position any end-to-end joins between the deck boards halfway across an inner joist so you can screw both boards into the joist for stability. Make sure you keep a gap of between 5-8mm to allow for expansion of the wood.
2. Begin to screw your deck boards to the joists. You’ll need to secure the deck board to every joist is covers along your deck frame. Use two screws for every joist. Mark where you’re going to add your screws, ensuring that they are at least 15mm from the end of the board and 20mm from the outside edges. Drill pilot holes for the screws, being careful to only drill through the deck board and not the joist. Then screw the decking screws into the holes.
3. Continue to screw in the deck boards, ensuring you leave the correct expansion gap. You can stagger the deck board joins across the deck for more strength.
4. Sand down any cut ends if you need to before applying decking preserver to protect the timber from rotting.

Do I Need A Gardener Or Landscaper?

This is a question that’s often asked by most homeowners across the globe. While it’s true that both gardener and landscaper can make your garden a lot more beautiful and pleasing to the eye, it’s also crucial to know the significant difference between the two professions.

So who is a landscaper? We have two types of landscapers: the landscape architect whose job is to design a landscape and a landscape builder whose job is to do the physical requirements of creating a landscape. Both types are very interrelated such that landscape architects can also be landscape builders or have one or more of the other type in same team (as most landscaping building projects will be supervised by a landscape architect).

Now the main difference between a landscaper and a gardener is the type or scope of work they’re qualified to undertake. Generally, landscapers require just one or more types of trade licences to work, meanwhile a gardener may or may not need a trade licence. So who is a gardener?

It’s the job of a gardener to come in and maintain the landscape garden once the landscape has successfully built the outdoor area. In other words, it’s part of a gardener’s services to prune plants, mow the lawns, do the weeding, fertilize your soil and much more. It’s not their job to construct a large retaining wall or a gazebo. And you can also be sure they won’t appear with a backhoe ready to sculpt your landscape.

Overall, deciding who to choose between a gardener and a landscape depends on the type or scope of work that’s required. With the aforementioned differences, you should be able to easily determine who to call when in need of a landscaping or gardening service.

• Decking joists
• Coach screws
• Coach bolts
• Combi drill
• Socket set
• A saw suitable for your project and the thickness of the timber
• Pencil
• Decking preservative
• Sandpaper or sander

1. Measure your deck frame and cut to size if necessary.
2. Make 2 pencil marks on each end of the frame’s 2 outer joists to mark where the coach screws will go. They need to align with the centre of the adjoining outer joist. Then, use a flat wood drill bit to drill recesses into each mark. Make them the same depth of the screws that your using’s head and wide enough for a ratchet or socket to tighten them.
3. Using a thinner drill bit, line up the outer joists and drill a pilot hole through the middle of the recess. These pilot holes act as a guide for the screws and stops them from splitting the wood.
4. Fit the coach screws with either a drill driver or socket and ratchet.
5. Repeat the process for the inner joists once you’ve assembled the outer frame.