Find a Landscaper you can trust in New Romney.

Whether you’re starting a garden from scratch or adding plants to a garden that needs a big of work, the biggest step in planting a garden is preparation. We’ll give you a few tips on how to plant a garden whatever your garden’s size. Check your soil The most important thing to do before you start to plant a garden is check your soil type. Different plants suit different soils, so you should choose ones that will like the soil in your garden. If your soil is sticky and muddy, it’s referred to as clay soil, but if it runs through your fingers when you pick it up it’s known as sandy. Ideally, you want something between the two to help your plants’ roots spread easily. If you have heavy clay soil, you’ll need to add well-rotted manure or compost to improve the structure, but if it’s sandy you’ll need to add organic matter to improve its fertility. Make a plan Don’t just start planting wherever – make sure you’ve got a plan of where you want everything to go. Do a simple drawing or cut out photos from magazines or the internet. How to plant bare root plants and trees When you’re planning what to plant in your garden, make sure you choose the correct amount and size of trees you’re going to plant. In a small to medium garden you only want one or two trees, and you don’t want anything too large that might spread too far. When you’re ready to plant, make sure there’s enough room for the roots to spread. Look for the soil ‘tide mark’ near the base which will show the depth that it was planted before, and use that as your guide. Dig your hole to the correct depth and width and fork the sides so it’s easier for roots to get in. Add some well-rotted manure and place the plant in the hole so the roots are spread out and fill the hole with soil. Planting potted plants Dig a hole deep enough for your plant – put the pot in the hole to check whether you’re there yet. You want around 2cm around the outside and don’t make the hole any deeper than the pot. If your plant has a tight root ball from outgrowing its pot, gently tease out the roots – it won’t harm the plant. How to plant plug plants in your garden Plug plants are usually mail-order plants that you get in spring and are a great way to start planting a garden. You must handle them carefully and water them before planting. Fill a small pot with compost and make a well in the centre, then drop the plug in. Gently pat the soil around it. You might need to pot them again to the next size up later on, and harden them off outside before planting them in the ground after there’s no risk of frost. With these few tips you can easily get started with planting your garden. But if you need some help and advice, get in touch with local gardeners who will be happy to give you a quote.

Yes, it is possible to insulate a shed. You might want to do this if you’re planning on working in it during the winter. A professional will be able to help you find an insulated shed or advise you on how to insulate a shed that you already have. Always seek professional advise first before attempting to do this yourself!

• Decking joists
• Coach screws
• Coach bolts
• Combi drill
• Socket set
• A saw suitable for your project and the thickness of the timber
• Pencil
• Decking preservative
• Sandpaper or sander

1. Measure your deck frame and cut to size if necessary.
2. Make 2 pencil marks on each end of the frame’s 2 outer joists to mark where the coach screws will go. They need to align with the centre of the adjoining outer joist. Then, use a flat wood drill bit to drill recesses into each mark. Make them the same depth of the screws that your using’s head and wide enough for a ratchet or socket to tighten them.
3. Using a thinner drill bit, line up the outer joists and drill a pilot hole through the middle of the recess. These pilot holes act as a guide for the screws and stops them from splitting the wood.
4. Fit the coach screws with either a drill driver or socket and ratchet.
5. Repeat the process for the inner joists once you’ve assembled the outer frame.

Is your driveway damaged or starting to show some signs of cracks and gaps? If yes, then you’d probably be thinking of repairing it before it gets even worse. Repairing a driveway is largely an unknown process but also a very tedious task as well. So if you’re looking to hire a professional for help, just how much is the repair going to cost? In this article, we’re going to look at the various factors that can determine the cost of a driveway repair.

In the UK, the average price of repairing a driveway is usually within the range of £1,400 to £1,800, where as the normal price of a driveway repair will range between £700 to £2,400. although some small repairs tasks can be as low as £250, while huge driveway repairs can skyrocket to about £4,200.

However, in general, the overall cost of repair a driveway can not be determined as each driveway is unique with their special repair needs. The factors that can influence the price of a driveway repair includes the material used, the perimeter of the driveway as well as the condition of the foundation. The only factor that’s not unique to any one driveway is the materials used, so let’s take a look at the differences in price using the based on the various types of materials available.

✓ Concrete. The average cost of repairing a concrete driveway is usually between £250 to £3,200. Have it in mind at most times the price of fixing an overly damaged driveway can be more than the cost of buying a new one.

✓ Asphalt. The average cost of repairing an asphalt driveway is usually between £750 to £2,800.

✓ Brick. The average cost of repairing a brick driveway is usually between £700 to £1,700.

✓ Cobblestone. The average cost of repairing a cobblestone driveway is usually between £500 to £1,600.

• Tongue and groove timber boards
• Boards for the ledges and braces, at least 20mm thick
• Nails
• Hammer
• Saws, including a circular saw
• Chisel
• Mallet

1. Cut your boards to size If you can’t buy boards at the right height and width for your door, cut the boards to length using a circular saw. Don’t forget to sand and treat any cut ends with timber preservative. Lay out the boards in the best arrangement for your shed door, with the inside of the door facing up.
2. Arrange the ledges and braces On most shed doors, you’ll probably need 3 boards across the back of the door to form the ledges. The ledges keep the door straight and keep the boards of the door together. The braces are the parts of the door that slope down to form a ‘Z’ shape between the ledges. Ensure that the braces are sloped up from the bottom and middle hinge to stop the door from sagging as the timber expands and contracts in the weather. Once you’re happy with the arrangement, mark the spots on the boards where they will meet and cut out of the housings using a chisel and mallet.
3. Put the door together Use clamps to pull the boards together and hold the ledges and braces in place. Nail from the front of the door through the boards and ledges to fix them. Secure the ledges and braces with screws; you may want to pre-drill and countersink holes to prevent the wood from splitting. Remember to treat them with preservative if you do.
4. Fix the shed door hinges Make sure you measure carefully before attaching the hinges, ensuring you know where the pin sits in relation to where the door opens.
5. Treat the door and add locks and handles Apply some wood oil, like linseed or teak oil, to help prevent water damage. Then add locks or handles to your shed to help keep it secure.
If you’d rather leave it to the professionals, there are plenty of specialists that will be able to make a shed door for you, or even put up an entire shed.

Most responsible contractors will dispose of the old fencing via an approved commercial waste site. Do check that the cost of taking rubbish away is included in the quotes you receive, otherwise you might find you get stung when it comes to paying for the work.

1. Remove any existing fascia boards Remove the fascia boards and the old felt if you’re re-felting.
2. Measure the shed roof Measure the roof, taking into account that you should leave around 50mm for overlaps at the eaves and 75mm at the gable ends. You’ll probably need 3 pieces of felt, but some smaller sheds only need 2.
3. Apply felt to the roof Once you’ve cut the felt to size, apply the each piece to the roof, pulling it tight. Then nail along the length of the roof at 100mm intervals. For nails at the bottom edge, they can be wider – around 300mm. If you’re adding a piece of felt in the middle of the shed along the apex, fix it using adhesive, then nail it at the lower edge at 50mm intervals.
4. Tidy up the overhangs Fold down the felt at each overhang and nail it securely. Cut a slit in the overhang at the apex using a pen knife, then fold that down and nail at 100mm intervals along the gable. If you like, you can add fascia boards to keep the shed looking neat. Use wood nails to secure them and then trim away any excess felt.