Find a Landscaper you can trust near you.

Do I Need A Gardener Or Landscaper?

This is a question that’s often asked by most homeowners across the globe. While it’s true that both gardener and landscaper can make your garden a lot more beautiful and pleasing to the eye, it’s also crucial to know the significant difference between the two professions.

So who is a landscaper? We have two types of landscapers: the landscape architect whose job is to design a landscape and a landscape builder whose job is to do the physical requirements of creating a landscape. Both types are very interrelated such that landscape architects can also be landscape builders or have one or more of the other type in same team (as most landscaping building projects will be supervised by a landscape architect).

Now the main difference between a landscaper and a gardener is the type or scope of work they’re qualified to undertake. Generally, landscapers require just one or more types of trade licences to work, meanwhile a gardener may or may not need a trade licence. So who is a gardener?

It’s the job of a gardener to come in and maintain the landscape garden once the landscape has successfully built the outdoor area. In other words, it’s part of a gardener’s services to prune plants, mow the lawns, do the weeding, fertilize your soil and much more. It’s not their job to construct a large retaining wall or a gazebo. And you can also be sure they won’t appear with a backhoe ready to sculpt your landscape.

Overall, deciding who to choose between a gardener and a landscape depends on the type or scope of work that’s required. With the aforementioned differences, you should be able to easily determine who to call when in need of a landscaping or gardening service.

1. Calculate the surface area for your decking Multiply the length (L) of your decking area by the width (W): L x W = Decking Surface Area (DSA) in m² 10 x 6 = 60m²
2. Work out the coverage of your deck boards Add your deck board width (DBW) to the expansion gap length (EGL), then add the deck board length (DBL) to the expansion gap width (EGW). Then multiply these numbers. (DBW + EGL) x (DBL + EGW) = Single Board Coverage (SBC) 0.144m + 0.005m = 0.149m 2.4m + 0.003m = 2.403m 0.149 x 2.403 = 0.358m²
3. Calculate the number of deck boards you need Multiply the SBC by 1.1 to allow for 10% wastage. Then, divide the DSA by the SBC. DSA / SCB x 1.1 = Total number of boards required 60m² / 0.358m² x 1.1 = 184.36 boards – so round up to 185 so you’re not left short.

When your driveway is suffering from depression, it becomes unsafe for driving (a danger zone) and ugly - no homeowner wants that! Unfortunately, most driveways won’t hold flat for long as they tend to develop cracks and potholes pretty quickly. Here, we are going to take you through how to fill asphalt driveways’ depression so as to ensure the sinkholes in your driveway poses no threat to you or your loved ones, while also beautifying your property. The approach to be used depends on the intensity of the depression. If its only a few cracks and holes, this can easily be repaired with some equipment. But if otherwise is the case, then calling a reliable professional will be your best bet. In this article, we’ll show you how to repair dips in your asphalt driveway relatively quickly.

✓ Pick a date with warm and sunny weather. This is because if you work in a cold weather, chances are the materials will freeze and hence, unusable. So find a day when the temperature will over 50 degrees Fahrenheit and below 80 degrees Celsius and when there would be no rain. We’ll advise a day between May to October.

✓ Prepare the area. Remove all loose stones, soil, dirt as well as vegetation from the holes. Once done, you can then proceed to washing the area with a pressure washer or sweep with a broom.

✓ Apply a thin mixture of asphalt to the area. Use a flat stirring stick to coat the low driveway area with a thin mixture of asphalt.

✓ Tamp the asphalt repair mix. Purchase the right kind of asphalt to repair the driveway. Fine aggregate asphalt mixture is more suited to filling small holes, whereas the coarse aggregate is more suited to filling larger holes. Apply layers ( about 2 inches each time) of the asphalt repair mix to the sunken area and use a shovel to give it a smooth finish. Once done, simply make the area smooth and protect it with a piece of plywood. Do not walk or drive on the area for a couple of days.

Laying artificial grass on concrete needs a slightly different approach to if you’re installing it over soil. The good news is that it’s much less labour intensive, as you don’t need to do any digging or levelling.

Ideally, your concrete base should be in good condition, and have an adequate fall on it to provide efficient drainage. If it doesn’t, you might have to do some repair work or drill some drainage holes first.

When you’re ready to start, begin by cleaning your concrete base. Use a jet wash or a hose and brush to dislodge and disperse any dirt or plant growth. Once it’s clean, leave it to dry completely.

Then, you need to fit an underlay - usually it’s made of foam. This will provide padding to make your artificial grass softer and more comfortable to walk on. It will also help to level out any slopes on uneven parts on the concrete. Make sure it’s a good-quality underlay that’s permeable – if it’s not, you could end up with damp artificial grass and nasty smells as it will hold moisture. Roll out the underlay and cut it to shape, taping any separate sections together.

Next, use an adhesive to secure the underlay to your concrete. Make sure you leave gaps in the adhesive to allow water to drain off easily. Leave the glue to dry, then you can start laying your grass.

Roll out your grass like you did with your underlay, cutting it to shape and joining any separate sections together with artificial grass tape. Then glue the grass to the underlay. Leave it dry, give the grass a brush, and it’ll be ready to use!

1. Place a post in the corner of the frame you created with the pegs and string. Measure and mark out 100mm from each side.
2. Dig out this soil to a depth of 700mm (watch out for cables or pipes). You should have a 300 x 300mm hole. Repeat for the other 3 corners.
3. Using a brick bolster, split a concrete block in two. Put a section of the block in each hole.
4. Get a length of post longer than you need and place one in each hole. You can cut it down later.
5. Create props on each post to hold them in place until you’re ready to add a cement mix. Check that they’re level. When you’re happy that they are, secure them in place with a concrete mix, making sure you create a slope in the concrete so that rainwater runs away from each post. When the concrete is set, remove the props.
6. Create a string line around each corner post and find the centre point between each. Place a timber batten at each point, ensuring that they’re not spaced any more than 1500mm apart.

1. Working from the corner where the deck will be at its highest above ground level, measure and mark on the post where the highest part of the frame will be.
2. Measure from the far side of one post to the opposite and cut sections of joist to size. Line up a piece of joist with the mark you made and temporarily secure it. Factor in a 2mm fall for every metre of decking so rainwater can run off.
3. Secure the frame to the other corner post, ensuring it’s at the right level. Do this for every side of the outer frame.
4. Using 100mm coach screws with washers hanging on the end, secure each end of the four sections of frame.
5. Mark out where the centre of the support posts will be and secure all of these posts to the frame, except the centre post.
6. Add your central support joists. These should run in the same direction as the deck boards will run. You’ll need to measure from the inside of the frame on one side to the inside of the frame on the opposite side. Attach the joist in the same way as you did for the other posts. Repeat so the centre post is in between two sections of frame and secure the posts with concrete.
7. Trim down all the posts to the correct height using a saw.
8. Add your weed-control fabric and weigh down with gravel across the entire area.

1. Measure 400mm from the centre of the outer frame and mark a line. This will be where the first joist is positioned. Repeat at 400mm intervals down the length of the frame – if the last one will be more than 400mm, add another joist to create enough support.
2. Attach a joist hanger to each end of the joist.
3. Place the joist in position so the centre lines up with the 400mm spacer mark.
4. Secure using external grade screws once you’re happy that the joist is flush with the frame.

1. Mark out the area and dig the top layer of soil, trying to get the ground as flat as possible.
2. Build a timber frame to size.
3. Measure out 4 rows of 3 blocks to create good weight distribution and lay in place.
4. Underneath each block, dig around 50mm wider than the blocks and about 150mm deep. Fill the hole with pea gravel until it’s flat.
5. Place timber planks along the rows of blocks and see how level it is. Add or remove blocks where necessary. If it’s only a small difference, use shingle underneath the timber until it’s level.
6. Nail your timber shed base to the timber planks to create a sturdy base for your shed.

How To Repair Sunken Concrete Driveway

If you have concrete driveway that’s cracked, uneven and mostly especially sunken, you’d know how distasteful it can be just viewing it on your property. A sunken concrete driveway is most likely caused by rainwater erosion removing the soil under it or a big root under it which as rotted over time. Another possible cause of the sunken concrete is an improperly prepared base which implies that the soil beneath wasn’t fully compact when the concrete was poured on it. Later on the soil beneath will eventually settle and shift below the concrete driveway which weakens the integrity of the entire driveway, making it more vulnerable to cracks, unevenness and sunken.

Two ways in which you can fix this problem includes either demolishing the whole driveway, re-compact the soil underneath and fill with new concrete or repair the entire driveway using an easy process called slabjacking. In this article, we’re going to look at the slabjacking repair process as it’s significantly less expensive than the demolishing approach and will also cause minimal disruption to your lifestyle.

Also referred to as mudjacking or concrete lifting, slabjacking is simply a process used to float your existing concrete back to its original position. If you are not a competent DIYer or lack confidence to pull this off, we’d recommend reach out to a professional for help. If otherwise, then you can practice the slabjacking process given below.

✓ Drill holes through the slab.

✓ Pump grout mixture through the holes. This mixture will spread out beneath he driveway and raise it up.

✓ Lastly, fill the holes and level the concrete driveway surface.in such a way to hide the signs of the repair made.

This is a process that works to efficiently get your driveway back in a top condition relatively quickly.

Properly erected fences shouldn’t require a great deal of maintenance. Any rotting boards can usually be replaced without replacing the whole panel. Timber fencing should be stained every 2-3 years. General maintenance is something you can carry out yourself, however, larger works may need a qualified professional to come in.