Find a Landscaper you can trust in Stirlingshire.

Is there a hole in your asphalt driveway you feel you can repair yourself? If it’s something you know you can confidently do then this step by step guide is just for you. If otherwise, then we’d recommend you hire the services of a reliable professional who can guarantee the best results while also saving you some time and extra money that could result from possible errors. In this article, we’d go over the reparation process of an asphalt driveway with a hole in it.

✓ Get the necessary tools. You’re going to need a broom ( to clean the area), caulking gun ( to fill the hole), a hand tamp a plate compactor or a hammer ( to level the filled in hole) and a weeding glove (just in case there are weeds growing in the hole).

✓ Prepare the area. Do this by weeding the plants or weeds that might have grown inside the hole and identify your asphalt filler.

✓ Wet your soil, if necessary. It’s important to note that this is only necessary if your soil is dry to help the filler stick properly.

✓ Fill in deep holes. If the hole goes down about 3 to 4 inches or more, simply fill it with any material like rocks, clay etc.

✓ Apply the asphalt filler. Fill the hole with the asphalt filler to about half an inch higher than the surface of the driveway.

✓ Level the filler. For a large hole, make use of a plate compactor or a hand stamp, but a hammer will be sufficient for smaller holes.

✓ Cover the hole, if necessary. If your home isn’t level, covering your hole with a piece of plywood is advisable.

✓ Clean off the seal. After the asphalt looks done and in place, simply brush away the debris from the seal to finish off the project.

1. Calculate the surface area for your decking Multiply the length (L) of your decking area by the width (W): L x W = Decking Surface Area (DSA) in m² 10 x 6 = 60m²
2. Work out the coverage of your deck boards Add your deck board width (DBW) to the expansion gap length (EGL), then add the deck board length (DBL) to the expansion gap width (EGW). Then multiply these numbers. (DBW + EGL) x (DBL + EGW) = Single Board Coverage (SBC) 0.144m + 0.005m = 0.149m 2.4m + 0.003m = 2.403m 0.149 x 2.403 = 0.358m²
3. Calculate the number of deck boards you need Multiply the SBC by 1.1 to allow for 10% wastage. Then, divide the DSA by the SBC. DSA / SCB x 1.1 = Total number of boards required 60m² / 0.358m² x 1.1 = 184.36 boards – so round up to 185 so you’re not left short.

There are quite a few different types of garden fencing that are readily available, so you’ll have plenty to choose from. If you’ve got a strict budget, waney edge panel fencing is a good option. It’s made up of horizontal wood strips and is generally the cheapest type of fencing. Another good option is closed feather-edge panels. These are a really strong type of fence, made up of concrete posts and panels of vertical strips of wood.You can also get more decorative types of fencing with combinations of vertical and horizontal wood strips.

If your deck isn’t going to be flat to the ground, it’s a good idea to have some kind of balustrade to avoid any tripping. If the gap between the deck and the ground is less than 600mm, use a 900mm balustrade. If it’s higher than 600mm, the balustrade should be 1100mm tall.

It’s a good idea to talk to your neighbours before you start any work to avoid confusion along the way. But if the fence is definitely your responsibility and on your property, there’s no legal obligation to notify them. It’s also a myth that you need to erect a fence with the flush side without posts facing your neighbour’s property.

1. Unroll your two pieces of artificial grass, ensuring that the pile is running in the same direction. Fold over each piece by about 300m.
2. To get the perfect seam, cut at least 3 tufts back, ensuring that you don’t trim any grass blades.
3. Either remove the backing on your self-adhesive tape and unroll it down the centre of the join, or roll it out ensuring that the shiny side is down then fix at either end with adhesive.
4. Fold over the grass onto the tape and bring each piece together, ensuring there’s a 2-3mm gap at the seam.
5. Where the pile runs over the edge of the seam, fold over the artificial grass.
6. Apply a small amount of adhesive under the edge of the first section of grass with a mastic gun, then add some to the front edge to stick the second piece.
7. Bring the seam together, ensuring that you don’t get any grass blades stuck. Place a plank with some heavy objects on over the join to ensure that it dries securely.

Gardens need regular maintenance and without it they can get really out of hand. When you’re thinking about how much gardeners charge, you should bear in mind the state of your garden and whether you need a one-off tidy up or want a regular ‘manicure’ of your garden to keep it looking neat and tidy. Gardeners generally charge in two different ways for their work depending on the job: with an hourly rate or with a fixed price. Generally, gardeners will charge an hourly rate of between £20 - £40 depending on their experience, the job and where you are in the country. They may also charge a minimum call-out charge since a lot of their day will include unpaid travel from job to job. If you don’t need your gardener for a full day, for example if you just need your lawn mowed, then they will probably charge a fixed rate. It’s unlikely to have anything to do with their hourly rate. We’ve found that the average fixed cost of a gardener is around £250 - but this of course includes small jobs like weeding and mowing to larger jobs like pulling out shrubs and replanting, so you may find that your gardener charges more or less than this. Bear in mind that most gardeners will charge a price that doesn’t include waste removal, since lots of people have compost heaps or garden waste bins. So if you need them to take the garden waste away, expect another £100 - £200 on top of your quote.