Find a Landscaper you can trust in Brandon.

1. If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia.
2. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws.
3. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist.
4. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3.
5. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first.

Try to put your shed in open space, away from trees, bushes and other buildings. This will help to protect it from falling branches and sap. It will also mean that you can access all sides of the shed for repair and maintenance purposes. Make sure you take a look at garden shed planning rules before you pick a final spot for your shed.

There is a variety of methods available to ensure that your paving drains properly, for example draining into a lawn or soakaway. Correct drainage of paving is a requirement for planning permission. See our guide on planning permission for paving for more information.

As a home or property owner, you’re generally allowed to build next to your neighbour’s fence as long as it’s on your own side of the property. With that in mind, there are certain laws that regulate how close a fence can be built to buildings on the same lot or neighbouring lots. In addition, there are also local bylaws that provide limitations on the placements as well as height of fences so as to address safety hazards. In this post, we’re going to give you a good insight into how close you can build to your neighbour. Let’s take a look!

In general, if the fence is in your boundary then you’re allowed to build a 2-metre high brick or wooden fence or wall. However, this may differ depending on your location in the UK. As a result, you may want to reach out to your municipality’s building department in order to determine what these rules and limitations are in your area. In the events whereby there are no such restrictions but you’re still concerned, you can try informing your neighbour what your concerns are. However, if they’re not receptive there are some steps you can take to ensure your plans go as smoothly as possible. These steps include the following:

• Ensure to leave sufficient space for both the posts and footings
• Stagger your fence posts in order to make sure you’re not digging your neighbour’s
• Consider using concrete posts as they’re much stronger and will last a lot longer
• Use kickers or plinths for raised gardens and flower beds
• Make use of concrete plinths as they won’t rot over time like a wooden fence.

Being a strong and durable product requiring little maintenance and expected to last over 2 decades, it’s little wonder resin is now a popular material amongst homeowners in the UK to build their driveways. However, there’s always the issue of the driveway fading, cracking or even becoming worn and tired. So is it possible to repair resin driveways? The answer is yes, a resin driveway can be repaired, however the best approach to use largely depends on the issue being faced. As a confident DIYer it’ll be very easy to do, but if you lack the confidence then calling in a professional for help would be a better option. So let’s take a look at how you can repair your resin driveways.

For cracks, the best reparation approach would be to chisel it out. Once done, then you can proceed to breaking the stones to form a rough edge. It’s important to make sure that the matrix of the stone remains unaffected. Make a new mixture of resin bound stone and pack it in tightly to the gap. While doing this, we’ll recommend making use of a plastic trowel to avoid burnishing. This fresh mixture will then create a smooth and perfect surface by interlocking with the edges. You can follow similar procedure for patches but these are larger holes or damages than cracks and as the name suggests are mostly likely to remain noticeable but will prevent further crumbling of your resin driveway.

For homeowners, who aren’t so keen about the patch repairs, you can opt for an overlay especially in the event whereby the majority of the surface has failed. Although many usually shy away from this approach because of the perceived high expenses, but the fact is that the approach is actually cost effective as you won’t have the need to spend more money in the long run.

Garden slabs are a joy to behold but only when done the right way. Well, the installation of paving slabs shouldn’t be exceed digging a little here and there, buying a small amount of mortar and pressing down the garden slab, right? Absolutely not! But we must admit how great it would have been if only it were that easy in real life. Let’s be honest, in reality, laying garden slabs does not only require you to prepare your sub-base painstakingly and mix your mortar using the appropriate materials, but you’d also have to work with accurate and precise paver placements to guarantee the patio’s longevity. Consequently, this happens to be a stressful and quite tricky challenge. If you lack the required confidence to pull this off, we’d recommend you hire the services of a seasoned professional who can guarantee the best results and also save you time and extra cash that may result from possible costly errors. In this guide, you’d gain more insight into the garden slabs laying process.

To get started, you’ll need sharp sand, cement, shovel, wheelbarrow, pointing trowel, rubber mallet, spirit level, jointing compound, hard-bristled brush and tarpaulin.

1. Mix a layer of mortar for each paver.
2. Apply the mixed mortar onto the sub base by using the trowel.
3. Slot the first flag in place and ensure not to stain the paver’s surface with the mixed mortar.
4. Using a rubber mallet, carefully tap the paver to the mortar bed. Once done, ensure the surface is even with a spirit level.
5. Take a measurement of the gap between the pavers
6. Repeat the above steps until all pavers have been perfectly laid
7. Leave the pavers to dry for about 1 to 2 days. You can protect it using a tarpaulin if concerned about rain.
8. Use the jointing compound to fill up the paver gaps to bind together the pavers. Ensure to wipe off any excess compound using the hard-bristled brush.

Pitting, also referred to as spalling is the event whereby “pits” or small holes start showing on the surface of your concrete driveway which makes it appear both worn and uneven. Concrete driveway pitting is a common but highly frustrating problem for most homeowners. You’ll see some concrete driveways that’ll only start to pit after a couple of years, but this is not true for all concrete driveways as others will start to show signs only after a couple of months. So how do you tackle this issue? Well, it’s relatively simple to tackle, however if you’re not confident or lack the necessary skills, we’d recommend you get in touch with a reliable professional who can guarantee the best results for help. In this guide, we’ll take you through the concrete driveway pitting repair process.

✓ Prepare the pits by cleaning the area, clearing out all debris and more. The small pits can be cleaned with a stiff brush while a sturdy broom will do a good job for larger pits.

✓ Make use of a hose to spray the concrete pits and flush out all remaining bits of waste.

✓ If you’re tackling series of small pits, simply use a caulking gun filled with pre-mixed epoxy and specially formulated for concrete to fill the pits. Clear off the excess eproxy ensuring that its level with the concrete surface. Once done, simply leave for at least 24 hours before the application of a concrete sealant to prevent the wear and tear of the new concrete.

✓ Chisel out a little concrete and clean with a pressure washer. Once done, apply a concrete resurfacing compound mixture into the holes and use a trowel to level off.

✓ Ensure that the repaired concrete driveway is protected from rain and foot traffic for at least 6 hours (or 24 hours for vehicles).

1. Calculate the surface area for your decking Multiply the length (L) of your decking area by the width (W): L x W = Decking Surface Area (DSA) in m² 10 x 6 = 60m²
2. Work out the coverage of your deck boards Add your deck board width (DBW) to the expansion gap length (EGL), then add the deck board length (DBL) to the expansion gap width (EGW). Then multiply these numbers. (DBW + EGL) x (DBL + EGW) = Single Board Coverage (SBC) 0.144m + 0.005m = 0.149m 2.4m + 0.003m = 2.403m 0.149 x 2.403 = 0.358m²
3. Calculate the number of deck boards you need Multiply the SBC by 1.1 to allow for 10% wastage. Then, divide the DSA by the SBC. DSA / SCB x 1.1 = Total number of boards required 60m² / 0.358m² x 1.1 = 184.36 boards – so round up to 185 so you’re not left short.