Find a Landscaper you can trust in Bognor Regis.

1. How to build a shed base out of paving slabs
   • Mix sand and cement together to make mortar or use a pre-mixed one
   • Use a trowel to lay mortar for 1 slab at a time on the sub-base and lift a damp-sided slab onto the mortar, using a piece of timber and club hammer to tap the slab into position carefully. Continue to lay the first row of slabs
   • Make equally-sized spacers in all the joints in the slabs to ensure they’re the same size, checking it’s level as you go along
   • Next lay slabs along the two adjacent outer edges, filling in the central area row by row
   • Leave the mortar to set according to the instructions or for at least 48 hours before filling in the joints with mortar or paving grout
2. Building a shed base from concrete
   • Create a wooden frame around your shed base area (also called formwork) to stop the concrete from spreading
   • Mix pre-mixed concrete with water or use 1 part cement to 5 parts ballast
   • Wet the sub-base using a watering can with a rose on the end
   • Pour the concrete onto the framed base starting in one corner
   • Push the blade of a shovel up and down in the edges of the concrete to get rid of air bubbles
   • Use a rake to spread the concrete, leaving it around 18mm higher than the top of the frame. Work in sections of around 1-1.m²
   • Compact the concrete using a straight piece of timber that’s longer than the width of the base. Move the timber along the site, hitting it along at about half of its thickness at a time until the surface is evenly ridged
   • Remove excess concrete and level the surface by sliding the timber back and forwards from the edge that you started. Fill in any depressions and repeat until even
   • Run an edging trowel along the frame to round off exposed edges of the concrete and prevent chipping
   • Cover the concrete with a plastic sheet raised on wooden supports to allow slow drying. Weigh it down with bricks
   • Once the concrete is set, you can install your shed and remove the wooden frame with a crowbar

With summer comes a lot of lawn challenges - from sod webworms, chinch bugs, nutsedge to drought stress, diseases and lots more. A lot of people find it hard to tell what’s happening to their lawn and probably assume it to be as a result of the summer stress and will definitely turn green again once the fall rolls in. This may be right in certain situations, but if you have fungi eating deep into your lawn, the green may not return. So, how exactly do you figure out if your lawn has diseases or pests? In this post, we’re going to provide you with a good insight into this to help you take the necessary treatment steps as soon as possible.

• Fungal structures. Fungi structures are not usually the easiest to spot as they vary in shape, colour and appearance. Fortunately, most fungi that appears on lawns will possess some type of structure which can be spotted when moisture is present. Once the night time dew sets in, you’ll be able to identify these strange growths in your lawn.
• Matted or Collapsed Areas. There is some sort of diseases that will make grass plant to wilt in little time. This, combined with fungi structures will make the grass look to have been matted in some areas.
• Discoloured or oily areas. Some areas are likely to show symptoms more than the others. While the unaffected turf may remain in its normal state, areas that are nearby may vary in colour due to the damage to the leaf tissue.
• Lesions or spots on leaves. Do you notice a certain damage pattern on the leaf blades of the grass plants? If yes, then your lawn is probably infected with a disease. Some of these spots may vary in size and colour.

If there’s a fence dividing yours and your neighbour’s properties that needs maintaining or replacing, you’ll want to know who owns it. Start by checking your deeds to see if there’s an existing boundary agreement. If there isn’t, have a chat with them to see if you can come to an arrangement yourselves.

How To Draw A Garden Landscaping Plan

Are you thinking about constructing a new garden landscape? Do you have an existing one but forgot where you planted those tulip bulbs the previous autumn? Or perhaps you’re just trying to identify the exact spot where you cut back that clump of wilted foxglove, without mistakenly digging it up. For everything to be much easier when it comes to a garden landscape, it’s always a wise decision to draw a garden landscaping plan.

To get started, let’s take a look at the materials you’ll need to acquire. These includes a piece of white paper on which the existing elements on your garden will be plotted, a piece of tracing paper and tape to give options for planned additions, a pencil, an eraser as well as a measuring tape.

For more accuracy while drawing your plan, you’ll need to measure the garden’s distances, perimeter, the existing garden beds size as well as the trees’ and shrubs’ shape and size.

• Write down the measurements taken on the scrap paper.

• Assuming it’s a medium sized backyard garden that’s 18 feet wide, we allocated a scale of 3 feet to equal an inch.

• Using a piece of white paper (could be graph if you wish) and a pencil, carefully outline the perimeter of the space. Once done, you can then sketch in the existing plants as well as other special features on the space (features that are of a permanent nature like trees, fences and paths).

• Hold a piece of tracing paper and tape in on top. Then you can sketch out the plants you wish to add to fill in the spaces in the garden on the tracing paper.

If your lawn edges are overgrown, it can make an otherwise well-cared for lawn look unsightly. Luckily, it’s easy to edge your lawn and make it look beautiful again. You should edge your lawn every spring and trim any overhanging grass you notice after mowing. How to edge a lawn There are different types of equipment you can use for different types of edging:

• Edging shears
• Half-moon edger
• Grass shears with a long handle
• Gardening knife
• Long rope or a plank of wood

Depending on how regularly you’ve maintained the edging of your lawn, you might want to do one of the following things:

• Annually in spring or if you’ve left the grass to get out of hand: Decide whether you want a straight or a curved edge along your lawn. If you want a straight edge, lay a plank of wood along the edge and use your half-moon edger to cut along. If you want a curve, lay a rope along the edge and cut along that. Or if you can still see the existing curve of the lawn, you can stick with that.
• After mowing: Use long-handled shears to trim the grass the mower couldn’t reach. If you want to make it look extra tidy, collect up the cuttings and put them on your compost heap or dispose of them.
• Overgrowing grass onto paths: Use a sharp gardening knife to cut the pieces of turf that are growing over the path and pull them away.
• When your lawn is flush with the path: Snip a clean edge along your path with your long-handled grass shears to make it look neat and tidy.
• If you’d rather a low-maintenance option: Spiked metal sheeting is a good material to use to keep your lawn’s edges at bay. Fix it in the ground along the edges to keep the outline of your lawn and stop it from growing into your borders.

The best way to keep your lawn edges looking fabulous is to keep them maintained. Remember to give them a little trim every time you mow your lawn to be the envy of all your neighbours.

1. Remove any existing fascia boards Remove the fascia boards and the old felt if you’re re-felting.
2. Measure the shed roof Measure the roof, taking into account that you should leave around 50mm for overlaps at the eaves and 75mm at the gable ends. You’ll probably need 3 pieces of felt, but some smaller sheds only need 2.
3. Apply felt to the roof Once you’ve cut the felt to size, apply the each piece to the roof, pulling it tight. Then nail along the length of the roof at 100mm intervals. For nails at the bottom edge, they can be wider – around 300mm. If you’re adding a piece of felt in the middle of the shed along the apex, fix it using adhesive, then nail it at the lower edge at 50mm intervals.
4. Tidy up the overhangs Fold down the felt at each overhang and nail it securely. Cut a slit in the overhang at the apex using a pen knife, then fold that down and nail at 100mm intervals along the gable. If you like, you can add fascia boards to keep the shed looking neat. Use wood nails to secure them and then trim away any excess felt.

There is a variety of methods available to ensure that your paving drains properly, for example draining into a lawn or soakaway. Correct drainage of paving is a requirement for planning permission. See our guide on planning permission for paving for more information.

There are several reasons why you may wish to plant a garden. To have a healthier environment, eat healthier, cook with fresh produce and lots more. Regardless of your purpose, one challenge faced by several home and property owners is exactly how to go about this and where to get started. If you’re having the same issues, then you’ve come to the right place. In this post, we’re going to take you through the process involved in planting a garden to ensure your project turns out a success. If you lack the confidence required to pull this off, we’d highly recommend you call in a professional who can guarantee the best results.

1. Start small. Being overly ambitious when planting a garden could be easiest way to a disastrous outcome. Give yourself a realistic goal and learn to plant healthy and productive plants by starting small.
2. Identify your site. To ensure a great garden, the plants need lots of sunlight. So, you can go for a space that gets about 6 to 8 hours of sunlight on a daily basis. Also, make sure that there’s a water source nearby to make it easy to give your plants water as required.
3. Choose you garden type. Decide how your garden will grow, be it in raised beds, in ground, in containers or a combination of styles. This will ensure that your garden is neat and orderly while also enhancing its curb appeal.
4. Make a list. Create a list of the plants you’d love to have in your garden.
5. Plan your planting. This involves spacing your plants as they’re going to grow bigger, deciding which plant goes where and identifying the best soil to grow them.
6. Get your plants.
7. Plant them.